Pioneer PDP 433CMX, PDP 503CMX specifications Supplement Explanation of Terms, Pin No Input Output

Page 43

		Additional Information


Supplement 2		Explanation of Terms
Signal assignment of INPUT 1 (Mini D-sub 15 pin		Aspect ratio
socket connector)		The TV screen’s width to height ratio is referred to as its aspect
		ratio. The aspect ratio on standard TVs is 4:3 and on wide TVs or
		High Definition TVs it is 16:9.

English

	5	1
	10	6
	15	11
Pin No.	Input	Output
1	R or CR/PR	+
2	G or Y	+
3	B or CB/PB	+
4	NC (No connection)	+
5	GND	+
6	GND	+
7	GND	+
8	GND	+
9	DDC + 5V	NC (No connection)
10	GND	+
11	NC (No connection)	+
12	DDC SDA	NC (No connection)
13	HD or H/V SYNC	+
14	VD	+
15	DDC SCL	NC (No connection)

Apple and Macintosh are registered trademarks of Apple Computer, Inc.

Microsoft is a registered trademark of Microsoft Corporation. NEC and PC-9800 are trademarks of NEC Corporation.

VESA and DDC are registered trademarks of Video Electronics Standards Association.

Power Management and Sun Microsystems are registered trademarks of Sun Microsystems, Inc.

VGA and XGA are registered trademarks of International Business Machines Co., Inc.

ENERGY STAR is a U.S. registered mark.

G ON SYNC

This indicates a video signal in the form of a synchronization signal added to the G (GREEN) signal of the R.G.B signal.

VGA

VGA is short for “Video Graphics Array”.

Generally this indicates a 640 dot x 480 line resolution.

XGA

General term for “eXtended Graphics Array”.

Generally this indicates a 1024 dot x 768 line resolution.

Additional Information

37

En

Image 43

Contents PDP-503CMXPDP-433CMX English Operating Instructions Safety Precautions Safety PrecautionsImportant Safety Instructions Iii Contents Features Example of PDP-503CMX Screen Display How to Use This ManualBefore Proceeding Screen DisplaysBefore Proceeding Press Menu to display the menu screen Press 5/∞/2/3 to adjust the valuePress 5/∞ to select the item to be adjusted About operations in this manualChecking Supplied Accessories Operation panel on the main unit Part Names and FunctionsMain Unit Main unitInserting the batteries Remote control unit Remote Control UnitWhen handling the remote control unit Connection Panel Operating range of the remote control unitAudio Output Stereo mini jack Illustration depicts PDP-503CMX model~ Speaker L terminal Audio Input Stereo mini jackInstallation and Connections Installation and ConnectionsInstallation of the Unit Installation using the supplied display standSide view diagram Wall-mount installation of the unitRear view diagram PDP-503CMX Rear view diagram PDP-433CMXConnection of separate Sync analog RGB Source When connecting to INPUT2Connection to INPUT1 and INPUT2 Connection to a personal computerWhen connecting to INPUT2 When connecting to Output INPUT1 When connecting to INPUT1Connection of G on Sync analog RGB source Making connections to the audio inputs on this unit Connecting the speakersAudio Connections Connection of composite Sync analog RGB SourceControl Cord Connection Power Cord ConnectionTo attach the speed clamps to the main unit How to Route CablesTo remove speed clamps Press 2/3 to select SET UP Setting Up the SystemSetup after Connection Screen Mode setupPress SET to select Locked Clamp Position setupSetup of Clamp Position Setting Up the SystemBefore you begin, make sure you have Press STANDBY/ON to put this unit in the operation modeOperations Selecting an Input SourcePress Display on the remote control unit To adjust the volumePress Volume on the remote control unit Press Muting on the remote control unitPress Screen Size to select the size During personal computer signal inputScreen Size Selection Changing the screen sizeSupported only on PDP-503CMX Moving the screen position upward or downwardPartial Image Enlargement When using Input Automatic Power OFFPress 5/∞ to select either the Power Management or Auto Power OFF modeAdjusting the Picture Quality Display Panel AdjustmentsTo reset Picture mode settings to the default Display Panel Adjustments Adjusting the Image Position and Clock Automatic AdjustmentTo reset Screen mode settings to the default Press SET to select Input Label Other OperationsRewriting the Input Display Other OperationsPress Menu Power Control FunctionPress SET to select Power Control Press 2/3 to select OptionOther Operations Press SET to select Input Audio Output Audio OUTPress 5/∞ to select Audio OUT Additional Information CleaningTroubleshooting About the self diagnosis modeProblems commonly mistaken as breakdown General problemsPanel sticking and after-image lag STANDBY/ON indicatorAdditional cautions Input/output AccessoriesGeneral PDP-503CMX General PDP-433CMXAdditional PC signal compatibilty table INPUT1, INPUT2Supplement 1 -1/2 PDP-503CMX InformationSupplement 1 -2/2 PDP-433CMX Pin No Input Output Supplement Explanation of Terms