Pioneer PDP 503CMX, PDP 433CMX Audio Connections, Connection of composite Sync analog RGB Source

Page 20

Installation and Connections

English

Connection of composite SYNC analog RGB

source

Make composite SYNC connections for a personal computer with output that has the vertical synchronization signal layered on top of the horizontal synchronization signal.

When connecting to INPUT1

 

 

 

 

INPUT1

OUTPUT

 

ANALOG RGB

 

 

(ANALOG RGB)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Audio Connections

Before making connections, be sure to check that the audio component’s power and the unit’s main power is off.

Connecting the speakers

This unit is equipped with speaker output jacks for connection to the speaker system (not supplied) specially designed for use with this unit. Refer to the illustrations below when making connections to the speaker terminals on this unit.

Twist exposed wire strands together.

Push tab to the open position, and insert the wire. Then, close tab firmly to secure the wire in place.

Installation and Connections

On-screen setup is necessary after connection. Please see pages 17 and 18.

When connecting to INPUT2

(ON SYNC)

 

INPUT2

(H/V SYNC)

 

G

B

R

HD

VD

75Ô2.2k

When using INPUT2, set the impedance selector switch to match the output impedance of the connected computer’s synchronization signal.

When the output impedance of the computer’s synchronization signal is below 75 , set this switch to the 75 position.

On-screen setup is necessary after connection. Please see pages 17 and 18.

Notes

÷When making composite SYNC connections, do not connect anything to the VD jack. If connected, the picture may not be displayed properly.

÷On some types of Macintosh® components, G ON SYNC and composite SYNC are both output. With this type of component, please connect using the G ON SYNC connection (see page 13).

Note

When making speaker connections, be sure to match the polarities (+ and –) of the speaker terminals on this unit and the corresponding terminals on the speakers. If the polarity is reversed, the sound will be unnatural and lack bass.

Making connections to the audio inputs on this unit

This unit features two audio inputs and one audio output. The following chart shows the video inputs and the corresponding audio input jacks.

Video

Audio input jacks

Sound output

input

 

 

 

 

 

INPUT1

 

Sound of the selected video

Stereo mini jack

input is output from the

 

INPUT2

(L/R)

• SPEAKER terminals

 

• Stereo mini jacks (L/R).

 

 

 

 

 

Audio connections for component (computer) connected to INPUT 1 or INPUT 2

 

 

AUDIO

VD

 

INPUT OUTPUT

 

75Ô2k.2

(INPUT1/2)

 

 

Audio input to the AUDIO INPUT jacks (stereo mini jack) is possible for a

component connected to either INPUT1 or INPUT2. Sound is output from both the AUDIO OUTPUT jacks (stereo mini jack) and the SPEAKER terminals according to the video input selection.

14

En

Image 20
Contents PDP-503CMXPDP-433CMX English Operating Instructions Safety Precautions Safety PrecautionsImportant Safety Instructions Iii Contents Features How to Use This Manual Before ProceedingScreen Displays Example of PDP-503CMX Screen DisplayPress 5/∞/2/3 to adjust the value Press 5/∞ to select the item to be adjustedAbout operations in this manual Before Proceeding Press Menu to display the menu screenChecking Supplied Accessories Part Names and Functions Main UnitMain unit Operation panel on the main unitWhen handling the remote control unit Remote Control UnitInserting the batteries Remote control unit Operating range of the remote control unit Connection PanelIllustration depicts PDP-503CMX model ~ Speaker L terminalAudio Input Stereo mini jack Audio Output Stereo mini jackInstallation and Connections Installation of the UnitInstallation using the supplied display stand Installation and ConnectionsWall-mount installation of the unit Rear view diagram PDP-503CMXRear view diagram PDP-433CMX Side view diagramWhen connecting to INPUT2 Connection to INPUT1 and INPUT2Connection to a personal computer Connection of separate Sync analog RGB SourceConnection of G on Sync analog RGB source When connecting to INPUT1When connecting to INPUT2 When connecting to Output INPUT1 Connecting the speakers Audio ConnectionsConnection of composite Sync analog RGB Source Making connections to the audio inputs on this unitPower Cord Connection Control Cord ConnectionTo remove speed clamps How to Route CablesTo attach the speed clamps to the main unit Setting Up the System Setup after ConnectionScreen Mode setup Press 2/3 to select SET UPClamp Position setup Setup of Clamp PositionSetting Up the System Press SET to select LockedPress STANDBY/ON to put this unit in the operation mode OperationsSelecting an Input Source Before you begin, make sure you haveTo adjust the volume Press Volume on the remote control unitPress Muting on the remote control unit Press Display on the remote control unitDuring personal computer signal input Screen Size SelectionChanging the screen size Press Screen Size to select the sizeMoving the screen position upward or downward Supported only on PDP-503CMXPartial Image Enlargement Automatic Power OFF Press 5/∞ to select either the PowerManagement or Auto Power OFF mode When using InputTo reset Picture mode settings to the default Display Panel AdjustmentsAdjusting the Picture Quality Adjusting the Image Position and Clock Automatic Adjustment Display Panel AdjustmentsTo reset Screen mode settings to the default Other Operations Rewriting the Input DisplayOther Operations Press SET to select Input LabelPower Control Function Press SET to select Power ControlPress 2/3 to select Option Press MenuPress 5/∞ to select Audio OUT Audio Output Audio OUTOther Operations Press SET to select Input Cleaning TroubleshootingAbout the self diagnosis mode Additional InformationGeneral problems Problems commonly mistaken as breakdownAdditional cautions STANDBY/ON indicatorPanel sticking and after-image lag Accessories General PDP-503CMXGeneral PDP-433CMX Input/outputPC signal compatibilty table INPUT1, INPUT2 Supplement 1 -1/2 PDP-503CMXInformation AdditionalSupplement 1 -2/2 PDP-433CMX Supplement Explanation of Terms Pin No Input Output