Pioneer PDP 433CMX, PDP 503CMX specifications Additional Information, Cleaning, Troubleshooting

Page 37

Additional Information

Cleaning

Regular cleaning will extend the life and performance of this unit. The recommended way to clean the display and related parts is described below.

Before cleaning, be sure to unplug the power cord from the power outlet.

Cleaning the display panel body and remote control

Do not under any circumstances use solvents such as benzine or thinner for cleaner. Use of such liquids may cause deterioration or peeling of paint from the display or remote control unit.

Wipe the display and remote control gently with a soft cloth. In the case of excessive dirt buildup, dampen a soft cloth with a diluted neutral cleaning detergent and after wringing the cloth thoroughly, wipe the component and then dry it with a dry soft cloth.

Cleaning the screen

After dusting, wipe the screen gently using the supplied cleaning cloth or a soft cloth. Do not use tissue or a rough cloth. As the surface of the screen is easily scratched, do not rub it or hit it with a hard object.

Cleaning the vents

As a general rule, use a vacuum cleaner about once a month to clean the vents on the rear panel of the display of dust buildup (set the vacuum cleaner to its weakest setting when doing this).

Using the unit without cleaning it of dust will cause the internal temperature to increase, resulting in possible breakdown or fire.

Vents

Vents

Vents

Vents

 

Vents

Illustration depicts PDP-503CMX model.

Troubleshooting

What may at first seem to be an malfunction, may be remedied with a quick check.

Please check to see if a warning is displayed on the screen. If displayed, refer to the table below and check the mode. If there is no display check to see if the problem is listed on page 32. The problem may also be caused by something other than this unit so please also check the other components being used such as a video deck. If the problem can still not be solved please consult the dealer where this unit was purchased.

About the self diagnosis mode

Messages appear on the bottom of this unit’s screen to indicate operation or connection faults. After message confirmation, check the condition of the unit.

ERROR MESSAGE

REMEDY

 

 

CAUTION

The current input signal is

OUT OF RANGE or

not supported by the unit.

CAUTION

Consult the table of

UNSUPPORTED SIGNAL

supported computer input

 

signals on pages 35 – 36

 

and set the computer's

 

output signal appropriately.

 

 

WARNING THERMAL ALERT

Turn off main power (page

 

9).

 

Is ambient temperature

 

too high?

 

Remove any objects

 

blocking the cooling vents

 

on the plasma display.

 

 

WARNING FAN FAILURE

Cooling fan has

 

malfunctioned.

 

Immediately turn off

 

power, remove power plug

 

from its outlet, and consult

 

a Pioneer service center or

 

your dealer.

 

 

ERROR INVALID KEY ENTRY

An invalid operation has

 

been attempted. Check

 

input signals, connections

 

and other settings.

 

 

SHUT DOWN

Turn off main power, wait

 

for 1-2 minutes, then try

 

turning power on again. If

 

problem persists, remove

 

power plug from its outlet

 

and consult a Pioneer

 

service center or your

 

dealer.

 

 

English

Additional Information

31

En

Image 37
Contents PDP-503CMXPDP-433CMX English Operating Instructions Safety Precautions Safety PrecautionsImportant Safety Instructions Iii Contents Features Before Proceeding How to Use This ManualScreen Displays Example of PDP-503CMX Screen DisplayPress 5/∞ to select the item to be adjusted Press 5/∞/2/3 to adjust the valueAbout operations in this manual Before Proceeding Press Menu to display the menu screenChecking Supplied Accessories Main Unit Part Names and FunctionsMain unit Operation panel on the main unitInserting the batteries Remote control unit Remote Control UnitWhen handling the remote control unit Connection Panel Operating range of the remote control unit~ Speaker L terminal Illustration depicts PDP-503CMX modelAudio Input Stereo mini jack Audio Output Stereo mini jackInstallation of the Unit Installation and ConnectionsInstallation using the supplied display stand Installation and ConnectionsRear view diagram PDP-503CMX Wall-mount installation of the unitRear view diagram PDP-433CMX Side view diagramConnection to INPUT1 and INPUT2 When connecting to INPUT2Connection to a personal computer Connection of separate Sync analog RGB SourceWhen connecting to INPUT2 When connecting to Output INPUT1 When connecting to INPUT1Connection of G on Sync analog RGB source Audio Connections Connecting the speakersConnection of composite Sync analog RGB Source Making connections to the audio inputs on this unitControl Cord Connection Power Cord ConnectionTo attach the speed clamps to the main unit How to Route CablesTo remove speed clamps Setup after Connection Setting Up the SystemScreen Mode setup Press 2/3 to select SET UPSetup of Clamp Position Clamp Position setupSetting Up the System Press SET to select LockedOperations Press STANDBY/ON to put this unit in the operation modeSelecting an Input Source Before you begin, make sure you havePress Volume on the remote control unit To adjust the volumePress Muting on the remote control unit Press Display on the remote control unitScreen Size Selection During personal computer signal inputChanging the screen size Press Screen Size to select the sizeSupported only on PDP-503CMX Moving the screen position upward or downwardPartial Image Enlargement Press 5/∞ to select either the Power Automatic Power OFFManagement or Auto Power OFF mode When using InputAdjusting the Picture Quality Display Panel AdjustmentsTo reset Picture mode settings to the default Display Panel Adjustments Adjusting the Image Position and Clock Automatic AdjustmentTo reset Screen mode settings to the default Rewriting the Input Display Other OperationsOther Operations Press SET to select Input LabelPress SET to select Power Control Power Control FunctionPress 2/3 to select Option Press MenuOther Operations Press SET to select Input Audio Output Audio OUTPress 5/∞ to select Audio OUT Troubleshooting CleaningAbout the self diagnosis mode Additional InformationProblems commonly mistaken as breakdown General problemsPanel sticking and after-image lag STANDBY/ON indicatorAdditional cautions General PDP-503CMX AccessoriesGeneral PDP-433CMX Input/outputSupplement 1 -1/2 PDP-503CMX PC signal compatibilty table INPUT1, INPUT2Information AdditionalSupplement 1 -2/2 PDP-433CMX Pin No Input Output Supplement Explanation of Terms