Pioneer PDP 433CMX, PDP 503CMX specifications Screen Size Selection, Changing the screen size

Page 27

Operations

Screen Size Selection

This unit incorporates screen modes of various height and width ratios. For optimal viewing, we recommend that you select the screen mode that best matches the video source that you are viewing. Although these modes are designed for full display of a picture on a wide screen, it is our hope that you make use of them with a full understanding of the manufacturer’s intentions.

Changing the screen size

The size of the image displayed on the screen, and the range of the image shown can be set in one of four modes on the PDP-503CMX, and in three modes on the PDP-433CMX.

Press SCREEN SIZE to select the size.

The screen size changes each time SCREEN SIZE is pressed as follows.

[PDP-503CMX]

	3 DOT BY DOT			3 4:3
	3 DOT BY DOT			3 4:3
		PARTIAL 2
					FULL 2
					FULL 2

[PDP-433CMX]

	3 DOT BY DOT	3 4:3
	3 DOT BY DOT	3 4:3

			FULL 2
			FULL 2

Consult the table Computer Signal Formats Supported (pages 35 and 36) for information regarding screen sizes supported by each signal format.

Notes

÷When the PARTIAL or FULL setting is used to display a non- wide screen 4:3 picture fully on a wide screen, a portion of the picture may be cut off or appear deformed.

÷Be aware that when the display is used for commercial or public viewing purposes, selecting the PARTIAL or FULL mode settings may violate the rights of authors protected under copyright law.

÷When DOT BY DOT or 4:3 screen sizes are selected, the display position is moved slightly each time the power is turned on, in order to prevent image burning.

During personal computer signal input

1DOT BY DOT

The input signal and the screen maintain a dot to line ratio of 1:1 and is thus highly faithful to the source.

[PDP-503CMX]


	A
	A		480 lines
			480 lines


							768 lines

640 dots

1280 dots

(Illustration shows 640 x 480 input.)

[PDP-433CMX]

*The PDP-433CMX is designed with horizontally oblong elements, with the result that the image displayed will appear more oblong than the original input signal.


	A
			480 lines


						768 lines

640 dots

1024 dots

(Illustration shows 640 x 480 input.)

24:3

The display fills the screen as much as possible without altering the aspect ratio of the input signal.

A

3FULL

The display is presented with a widescreen aspect ratio of 16:9 and fills the entire screen.

A

21

English

Operations

En

Image 27

Contents PDP-503CMXPDP-433CMX English Operating Instructions Safety Precautions Safety PrecautionsImportant Safety Instructions Iii Contents Features Example of PDP-503CMX Screen Display How to Use This ManualBefore Proceeding Screen DisplaysBefore Proceeding Press Menu to display the menu screen Press 5/∞/2/3 to adjust the valuePress 5/∞ to select the item to be adjusted About operations in this manualChecking Supplied Accessories Operation panel on the main unit Part Names and FunctionsMain Unit Main unitRemote Control Unit Inserting the batteries Remote control unitWhen handling the remote control unit Connection Panel Operating range of the remote control unitAudio Output Stereo mini jack Illustration depicts PDP-503CMX model~ Speaker L terminal Audio Input Stereo mini jackInstallation and Connections Installation and ConnectionsInstallation of the Unit Installation using the supplied display standSide view diagram Wall-mount installation of the unitRear view diagram PDP-503CMX Rear view diagram PDP-433CMXConnection of separate Sync analog RGB Source When connecting to INPUT2Connection to INPUT1 and INPUT2 Connection to a personal computerWhen connecting to INPUT1 When connecting to INPUT2 When connecting to Output INPUT1Connection of G on Sync analog RGB source Making connections to the audio inputs on this unit Connecting the speakersAudio Connections Connection of composite Sync analog RGB SourceControl Cord Connection Power Cord ConnectionHow to Route Cables To attach the speed clamps to the main unitTo remove speed clamps Press 2/3 to select SET UP Setting Up the SystemSetup after Connection Screen Mode setupPress SET to select Locked Clamp Position setupSetup of Clamp Position Setting Up the SystemBefore you begin, make sure you have Press STANDBY/ON to put this unit in the operation modeOperations Selecting an Input SourcePress Display on the remote control unit To adjust the volumePress Volume on the remote control unit Press Muting on the remote control unitPress Screen Size to select the size During personal computer signal inputScreen Size Selection Changing the screen sizeSupported only on PDP-503CMX Moving the screen position upward or downwardPartial Image Enlargement When using Input Automatic Power OFFPress 5/∞ to select either the Power Management or Auto Power OFF modeDisplay Panel Adjustments Adjusting the Picture QualityTo reset Picture mode settings to the default Display Panel Adjustments Adjusting the Image Position and Clock Automatic AdjustmentTo reset Screen mode settings to the default Press SET to select Input Label Other OperationsRewriting the Input Display Other OperationsPress Menu Power Control FunctionPress SET to select Power Control Press 2/3 to select OptionAudio Output Audio OUT Other Operations Press SET to select InputPress 5/∞ to select Audio OUT Additional Information CleaningTroubleshooting About the self diagnosis modeProblems commonly mistaken as breakdown General problemsSTANDBY/ON indicator Panel sticking and after-image lagAdditional cautions Input/output AccessoriesGeneral PDP-503CMX General PDP-433CMXAdditional PC signal compatibilty table INPUT1, INPUT2Supplement 1 -1/2 PDP-503CMX InformationSupplement 1 -2/2 PDP-433CMX Pin No Input Output Supplement Explanation of Terms