Panasonic WJ-ND400 manual Connectivity for Control Output, Signal ground Time adjustment input

Page 34

ND400_Basic.book 34 ページ 2008年4月8日 火曜日 午後3時59分

About Connectors

Auto Adjustment Time Function Connection 2

When settings menu - [Basic] - [Time & date] - [Auto adjustment time] is set to [Slave]

[Time Adjust Input] is available and the time on the recorder is synchronized with the other devices.

15 minutes before or after the set [Activation time] if a signal output from another device is input to the Adjustment Time I/O, the time on the recorder is set to the [Activation time].

Example:

When the [Activation time] is set to 15:00

A signal is received at 2:50:00 pm Set to 3:00:00 pm

A signal is received at 3:14:45 pm Set to 3:00:00 pm

A signal is received at 3:20:00 pm Time is not adjusted.

Terminal for other devices

(Signal ground)

(Time adjustment input)

13 20

Signal ground

Sensor input

Alarm Input

Alarm reset input

Series recording input

Time adjustment input

Signal ground

Alarm output

Alarm restore output

Front panel LED monitor output

Alarm recording

Recording

Disk

 

 

 

Buzzer output

System error output

Temperature warning output

Time adjustment output

Series recording output

ALARM/CONTROL

Important:

When [Auto adjustment time] is set to [Slave], time adjustment is not performed during emergency recording and event recording.

Connectivity for Control Output

Connecting alarm equipment like the buzzer and indicator to pins 15 to 18 sounds the buzzer, lights the indicator and indicates operating status when a signal is output.

An example of HDD error output (pin 16) is shown below.

(Signal ground)

 

(HDD error output)

13

16

Alarm equipment

 

 

 

Relays etc.*

ALARM/CONTROL

*Attached when necessary.

 

34

Image 34
Contents Network Disk Recorder Installation Guide Model No. WJ-ND400For Your Safety Please Read the Following Text CARE- Fully This Class a digital apparatus complies with Canadian Ices ND400Basic.book 4 ページ 2008年4月8日 火曜日 午後3時59分 Contents Contents AttachmentsPreface About these Operating InstructionsTrademarks and Registered Trademarks System Requirements for a PCNetwork Security Precautions Place the unit horizontally on a level surface Indication labelHandle the unit with care MPEG-4 Visual patent portfolio license GPL/LGPLMajor Operating Controls and Their Functions Front ViewMajor Operating Controls and Their Functions Inside the Front Cover HDD access indicator A/FHDD status indicator STS USE button USEHDD bay slots RAID mode switch RAIDRemoval knob Using the Brace Rear ViewHDD Space Management Outline of FunctionsMega Pixel Camera Compatibility and Capacity Replace HDDsOutline of Functions HDD Fault Tolerance SystemEncrypting Data Recorded on the HDDs Stable recording and playback of images Setting SchedulesRecording and Playing Images Event FunctionsEvent operations include the following Setup Menu ListList of Functions Live MonitoringRemote Operation NetworkNetwork Security Function SD Memory Recording Maintenance Version UpgradeRecording Rate Setting Acquiring images stored on the SD memory cardSetup Procedure Getting StartedRack Mounting Setting up the RackInstall the recorder in the rack Remove the 5 rubber feet from the underside of the recorderSetting up the Rack Rack mounting positionsConnections Connecting the PC and the CameraUsing a HUB for Direct Connection Port OperationND400Basic.book 26 ページ 2008年4月8日 火曜日 午後3時59分 Connecting to a PC over Adsl Example of Connectivity with 1 Port OperationConnecting multiple units to the recorder HubhubExample of Connectivity with 2 Port Operation HUB WANND400Basic.book 30 ページ 2008年4月8日 火曜日 午後3時59分 Connecting the Extension Unit Secure connection cablePin Assignments About ConnectorsUsing the Alarm/Control connector Pin Name Description of Operation Remarks NumberAuto Adjustment Time Function Connection About ConnectorsConnectivity for Switching to External Recording Connectivity for Emergency RecordingSignal ground Time adjustment input Connectivity for Control OutputUninterruptible Power Supply UPS Connectivity Using the Alarm Connector Alarm Connectivity Connectors Active Time Remarks Turning Off the Power Power SupplyTurning On the Power During RecordingUsing the Front Panel for Operations Basic OperationsUsing the Front Panel for Operations Checking System InformationCamera port Client PC port Maintenance port Checking the IP AddressConfiguring the Settings for Each Item Setting the IP AddressSetting and Canceling Key Lock Click the SET button when the cursor isHDD Unit Use the two screws to fasten the bottom of the HDDHandling the HDD ReferenceHDD is automatically recognized Installing HDDsPress the USE button for over 2 seconds Install the HDD units in the extension unit Installing HDDs by unitCheck the available disk space Removing HDDs Remove the HDD unit Check the disk informationPress the knob on the HDD unit Removing HDDs by unitOpen the lever Remove the HDD unit Hold down the USE button and turn on the power to boot up Setting the HDDs Operation ModeTurn off the recorder HDD Error Recovery During RAID Operation Data source During HDD error malfunction During recoveryReplacing Faulty HDD during RAID Operation Rebooting Problems TroubleshootingProblem Check item/remedy Troubleshooting WJ-ND400 SpecificationsGeneral Specifications Input/outputAccessories Standard AccessoriesIndex AdslPanasonic Canada Inc For European and other fields Panasonic Sales Company
Related manuals
Manual 233 pages 11.08 Kb

WJ-ND400 specifications

The Panasonic WJ-ND400 is a robust network video recorder (NVR) designed for reliable and scalable surveillance solutions. It serves as a central component in a modern security system, enabling the management and storage of video data from IP cameras. This device is particularly well-suited for a variety of applications, ranging from small retail setups to large enterprise installations.

One of the key features of the WJ-ND400 is its impressive storage capacity, supporting up to 16 terabytes of internal storage. This allows for extended recording times and the ability to retain high-resolution video footage without sacrificing quality. It supports various video compression formats, such as H.264 and H.265, which optimize file sizes and bandwidth use while maintaining clarity.

The WJ-ND400 boasts an intuitive user interface that facilitates seamless configuration and management of the recording settings. Users can access the device through a web browser, providing a convenient way to monitor live feeds, playback recorded footage, and manage camera settings from anywhere with an internet connection. This remote access feature is critical for businesses that require flexible surveillance management.

In terms of connectivity, the NVR supports Power over Ethernet (PoE), allowing for simplified installations by reducing the need for additional power supplies for IP cameras. The WJ-ND400 also utilizes a 10/100/1000 BASE-T Ethernet interface that ensures high-speed data transfer, optimizing the performance of connected devices.

Moreover, the WJ-ND400 is compatible with a wide range of Panasonic IP cameras, enhancing its versatility within a surveillance setup. It supports up to 64 channels of video input, enabling integration of multiple cameras for comprehensive coverage of surveillance areas.

Advanced features include motion detection and scheduled recording, allowing users to customize recording parameters based on specific needs. The NVR can also provide event alerts and notifications, enhancing its capability to respond to security incidents in real time.

In conclusion, the Panasonic WJ-ND400 stands out for its powerful storage capabilities, user-friendly interface, and extensive compatibility with various cameras. Its efficient use of high-quality video compression, combined with robust networking features, makes it an optimal choice for organizations looking to enhance their security infrastructure.