Panasonic WJ-ND400 manual Troubleshooting

Page 56

ND400_Basic.book 56 ページ 2008年4月8日 火曜日 午後3時59分

Troubleshooting

Problem

Check item/remedy

Page

 

 

 

 

Make sure the HDD unit is firmly inserted into the disk slot.

page 53

 

 

 

 

The HDD you are trying to recover data from has errors.

-

Cannot recover data after replacing

 

 

Make sure that the capacity of the replaced HDD is not smaller than the

 

HDDs

 

original HDD.

 

(In RAID5/RAID6 mode)

 

Even if the capacity is the same, the space may be smaller by a few percent

 

 

page 45

 

if the HDD models are different. All the HDDs must be the same model.

 

 

 

Also, use a replacement HDD that has equal or greater capacity than the

 

 

original.

 

 

 

 

HDD indicator lights orange and red

 

 

alternately even though recording or

Make sure that data is not recovered in RAID5/RAID6 mode.

page 52

playback is not done.

 

 

 

 

 

The power cord insulation is damaged.

 

-

 

The power cord, AC inlet or the power plug is damaged.

 

The power cord, AC inlet or the power

 

If you continue to use it, a fire or an electric shock may occur.

-

plug are hot during use.

Unplug the power cord immediately, and refer servicing to qualified service

 

 

 

The power cord gets warm or hot if bent

personnel.

-

 

or pulled during use.

 

 

 

 

 

 

[EXTu ERR INITIAL ERR] is displayed

 

Installation

 

Guide for

on the LCD.

After the extension unit is initialized, reconnect the extension unit.

expansion

u: Unit number

 

 

units

 

 

 

 

 

56

Image 56
Contents Network Disk Recorder Installation Guide Model No. WJ-ND400For Your Safety Please Read the Following Text CARE- Fully This Class a digital apparatus complies with Canadian Ices ND400Basic.book 4 ページ 2008年4月8日 火曜日 午後3時59分 Contents Contents AttachmentsPreface About these Operating InstructionsNetwork Security System Requirements for a PCTrademarks and Registered Trademarks Precautions Indication label Handle the unit with carePlace the unit horizontally on a level surface MPEG-4 Visual patent portfolio license GPL/LGPLMajor Operating Controls and Their Functions Front ViewMajor Operating Controls and Their Functions HDD access indicator A/F HDD status indicator STSInside the Front Cover USE button USERemoval knob RAID mode switch RAIDHDD bay slots Using the Brace Rear ViewOutline of Functions Mega Pixel Camera Compatibility and CapacityHDD Space Management Replace HDDsEncrypting Data Recorded on the HDDs HDD Fault Tolerance SystemOutline of Functions Setting Schedules Recording and Playing ImagesStable recording and playback of images Event FunctionsSetup Menu List List of FunctionsEvent operations include the following Live MonitoringNetwork Security Function NetworkRemote Operation Maintenance Version Upgrade Recording Rate SettingSD Memory Recording Acquiring images stored on the SD memory cardSetup Procedure Getting StartedSetting up the Rack Install the recorder in the rackRack Mounting Remove the 5 rubber feet from the underside of the recorderSetting up the Rack Rack mounting positionsConnecting the PC and the Camera Using a HUB for Direct ConnectionConnections Port OperationND400Basic.book 26 ページ 2008年4月8日 火曜日 午後3時59分 Connecting to a PC over Adsl Example of Connectivity with 1 Port OperationConnecting multiple units to the recorder HubhubExample of Connectivity with 2 Port Operation HUB WANND400Basic.book 30 ページ 2008年4月8日 火曜日 午後3時59分 Connecting the Extension Unit Secure connection cableAbout Connectors Using the Alarm/Control connectorPin Assignments Pin Name Description of Operation Remarks NumberAbout Connectors Connectivity for Switching to External RecordingAuto Adjustment Time Function Connection Connectivity for Emergency RecordingSignal ground Time adjustment input Connectivity for Control OutputUninterruptible Power Supply UPS Connectivity Using the Alarm Connector Alarm Connectivity Connectors Active Time Remarks Power Supply Turning On the PowerTurning Off the Power During RecordingUsing the Front Panel for Operations Basic OperationsUsing the Front Panel for Operations Checking System InformationCamera port Client PC port Maintenance port Checking the IP AddressSetting the IP Address Setting and Canceling Key LockConfiguring the Settings for Each Item Click the SET button when the cursor isHDD Unit Use the two screws to fasten the bottom of the HDDHandling the HDD ReferencePress the USE button for over 2 seconds Installing HDDsHDD is automatically recognized Check the available disk space Installing HDDs by unitInstall the HDD units in the extension unit Removing HDDs Remove the HDD unit Check the disk informationOpen the lever Remove the HDD unit Removing HDDs by unitPress the knob on the HDD unit Turn off the recorder Setting the HDDs Operation ModeHold down the USE button and turn on the power to boot up HDD Error Recovery During RAID Operation Data source During HDD error malfunction During recoveryReplacing Faulty HDD during RAID Operation Rebooting Problem Check item/remedy TroubleshootingProblems Troubleshooting Specifications General SpecificationsWJ-ND400 Input/outputAccessories Standard AccessoriesIndex AdslPanasonic Canada Inc For European and other fields Panasonic Sales Company
Related manuals
Manual 233 pages 11.08 Kb

WJ-ND400 specifications

The Panasonic WJ-ND400 is a robust network video recorder (NVR) designed for reliable and scalable surveillance solutions. It serves as a central component in a modern security system, enabling the management and storage of video data from IP cameras. This device is particularly well-suited for a variety of applications, ranging from small retail setups to large enterprise installations.

One of the key features of the WJ-ND400 is its impressive storage capacity, supporting up to 16 terabytes of internal storage. This allows for extended recording times and the ability to retain high-resolution video footage without sacrificing quality. It supports various video compression formats, such as H.264 and H.265, which optimize file sizes and bandwidth use while maintaining clarity.

The WJ-ND400 boasts an intuitive user interface that facilitates seamless configuration and management of the recording settings. Users can access the device through a web browser, providing a convenient way to monitor live feeds, playback recorded footage, and manage camera settings from anywhere with an internet connection. This remote access feature is critical for businesses that require flexible surveillance management.

In terms of connectivity, the NVR supports Power over Ethernet (PoE), allowing for simplified installations by reducing the need for additional power supplies for IP cameras. The WJ-ND400 also utilizes a 10/100/1000 BASE-T Ethernet interface that ensures high-speed data transfer, optimizing the performance of connected devices.

Moreover, the WJ-ND400 is compatible with a wide range of Panasonic IP cameras, enhancing its versatility within a surveillance setup. It supports up to 64 channels of video input, enabling integration of multiple cameras for comprehensive coverage of surveillance areas.

Advanced features include motion detection and scheduled recording, allowing users to customize recording parameters based on specific needs. The NVR can also provide event alerts and notifications, enhancing its capability to respond to security incidents in real time.

In conclusion, the Panasonic WJ-ND400 stands out for its powerful storage capabilities, user-friendly interface, and extensive compatibility with various cameras. Its efficient use of high-quality video compression, combined with robust networking features, makes it an optimal choice for organizations looking to enhance their security infrastructure.