Panasonic TY-ST42PT3K, TY-WK42PV1, TY-WK42PR1, TY-ST42PT3S, TY-ST42PW1 Removing the display unit

Page 22

Removing the display unit

1

2

Remove the two fixing screws from the sides of the holding bracket.

1)Lift the display slightly;

2)Pull the bottom half way to detach the lower insulating spacers;

3)Lift the display away from the holding bracket.

Fixing screws (left and right)

3)

2)

1)

Insulating spacer

Holding bracket

2-8

Image 22

Contents Pedestal Some notes on how to read this manual How to use this manualOther notes Before installing Optional parts list Tools listAccessory list SpeakersPedestal Parts listWall stand Wall-hanging bracket vertical Mobile standWall-hanging bracket angled Ceiling unit Points to note during installationSpeakers Dimensions of the display unit Units mmPage Pedestal TY-ST42PT3S TY-ST42PT3KAttaching the pedestal to the display unit Instruction of the installationAssembling the pedestal ScrewsFront Fixing the display unit Fixing the display unit to a deskRear Fixing the display unit to the wall Wall stand TY-ST42PW1Installation diagram DescriptionAssembling the wall stand Display unit face down Fixing the insulating spacers to the display unitProvisionally tighten the fixing screws Remove the screws and coversRemove the four screws Screw through and , then screw the four to the display unitAttaching the wall stand to the display unit Base of the display unit as shown in the illustrationHolding bracket Fixing screws left and right Lower the display into placeRemoving the display unit Mobile stand TY-ST42PF31020 40 5/32 610 24 820 89 3 33/64 400 15 3/4Then fix them from below using the four bolts Assembling the mobile standFixing the display unit to the stand Display unit as shown in the illustration belowFixing the wiring Mounting holes in the rear of the supportRemoving the display unit Wall-hanging bracket vertical TY-WK42PV1930 100 660 490 450 320 610 69.5 450 900 1020Installation diagram For Multi Screen 120Fixing the wall-hanging bracket to the wall 930 450 490Remove the four screws from the display UnitInto the holes Fixing screwsleft and right Attaching the display unit to the wall- hanging bracketNotches Insultating spacer Bracket, and then lower the display unit into placeSpacers Fixing srews Lower insulating Left and right SpacerLift the display away from the wall-hanging bracket If UN Official Bracket is Used Wall-hanging bracket angled TY-WK42PR1930 100 660 490 450 310450 900 1020 Insert and fasten a M6 screw bolt into the center-top hole 5tilt 10tilt 15tilt 20tilt No tilt Adjusting the angle of the display fittingTilt No tilt Stay Screw bolts into the remaining five holesFixing the insulating spacers to the display Wall-hanging bracket Attaching the display unit to the wall- hangingbracketFixing screws Insulating spacer Fixing screws mountsFoxing screws Insulating spacer Left and right Lift the display unit slightlyCeling unit TY-CE42PS1431 Fixing bolt M8-12 Ceiling unit Lower section Upper section Assembling the ceiling unitPrepare the ceiling unit Installing to a wooden structureexample Installation the ceiling unitCeiling board White line Hidden Side Prepare the display Install the insulating spacers in the display unitQuite los cuatro pernos Fixing screw M5 1 each Left and right sides Mount the display in the ceiling unitInsulating spacer Notch DownwardAdjust the ceiling units angle Connecting pipe Angle Adjustment Hole positions VerticalAdjust the ceiling units direction Fixing bolt M8-20Cable tie Gather the cablesInsulating Fixing screw M5 SpacerSpeakers TY-SP42PM3W TY-SP42PWD3W10089 610 Left Speaker 89100 Right Speaker Safety PrecautionsDo not suspend the speakers Attach the sponges to the speakers Sponges For right For leftHook Slot Rear of Wide Plasma Display Attach the speakers to the Wide Plasma DisplaySecure the speakers in place Bracket mounting screw Rear of Wide Plasma DisplayConnect the speaker cables Preparing the ends of the speaker cablesCentral P.O. Box 288, Osaka 530-8692, Japan

Related manuals

Manual 1 pages 52.7 Kb