Panasonic TY-ST42PT3K, TY-WK42PV1 Adjusting the angle of the display fitting, Tilt No tilt Stay

Page 40

3	Use a level gauge to correct the alignment of the wall-hanging bracket,
	and screw bolts into the remaining five holes.

4 Provisionally tighten the fixing screws.

After determining the positions and checking them against the bracket, embed M6 bolts or nuts. Furthermore, when embedding the bolts, ensure that the bolts protrude from the wall by 10 to 15 mm.

Adjusting the angle of the display fitting

The angle of the display fitting can be adjusted to one of the five positions ranging from vertical to 20 tilt in 5 steps.

At the time of shipment, the angle of tilt is set to 5 from vertical. To change this angle, adjust the position of the stay.

5 tilt

15 tilt

No tilt

stay

If the screws protrude more than 5 mm, it will not be possible to install the Wide Plasma Display in the correct position.

The stay is not needed if the display unit is to be fixed vertically.

Angle adjustment positions

5tilt 5

10tilt 10

15tilt 15

20tilt 20

No tilt 0

5-4

Image 40

Contents Pedestal Some notes on how to read this manual How to use this manualOther notes Before installing Optional parts list Tools listAccessory list SpeakersPedestal Parts listWall stand Wall-hanging bracket vertical Mobile standWall-hanging bracket angled Ceiling unit Points to note during installationSpeakers Dimensions of the display unit Units mmPage Pedestal TY-ST42PT3S TY-ST42PT3KInstruction of the installation Assembling the pedestalAttaching the pedestal to the display unit ScrewsFront Fixing the display unit Fixing the display unit to a deskRear Fixing the display unit to the wall Wall stand TY-ST42PW1Installation diagram DescriptionAssembling the wall stand Fixing the insulating spacers to the display unit Provisionally tighten the fixing screwsDisplay unit face down Remove the screws and coversRemove the four screws Screw through and , then screw the four to the display unitAttaching the wall stand to the display unit Base of the display unit as shown in the illustrationHolding bracket Fixing screws left and right Lower the display into placeRemoving the display unit Mobile stand TY-ST42PF31020 40 5/32 610 24 820 89 3 33/64 400 15 3/4Then fix them from below using the four bolts Assembling the mobile standFixing the display unit to the stand Display unit as shown in the illustration belowFixing the wiring Mounting holes in the rear of the supportRemoving the display unit Wall-hanging bracket vertical TY-WK42PV1930 100 660 490 450 320 610 69.5 450 900 1020Installation diagram For Multi Screen 120Fixing the wall-hanging bracket to the wall 930 450 490Remove the four screws from the display UnitInto the holes Attaching the display unit to the wall- hanging bracket Notches Insultating spacerFixing screwsleft and right Bracket, and then lower the display unit into placeSpacers Fixing srews Lower insulating Left and right SpacerLift the display away from the wall-hanging bracket If UN Official Bracket is Used Wall-hanging bracket angled TY-WK42PR1930 100 660 490 450 310450 900 1020 Insert and fasten a M6 screw bolt into the center-top hole Adjusting the angle of the display fitting Tilt No tilt Stay5tilt 10tilt 15tilt 20tilt No tilt Screw bolts into the remaining five holesFixing the insulating spacers to the display Attaching the display unit to the wall- hangingbracket Fixing screws Insulating spacerWall-hanging bracket Fixing screws mountsFoxing screws Insulating spacer Left and right Lift the display unit slightlyCeling unit TY-CE42PS1431 Fixing bolt M8-12 Ceiling unit Lower section Upper section Assembling the ceiling unitPrepare the ceiling unit Installing to a wooden structureexample Installation the ceiling unitCeiling board White line Hidden Side Prepare the display Install the insulating spacers in the display unitQuite los cuatro pernos Mount the display in the ceiling unit Insulating spacer NotchFixing screw M5 1 each Left and right sides DownwardConnecting pipe Angle Adjustment Hole positions Vertical Adjust the ceiling units directionAdjust the ceiling units angle Fixing bolt M8-20Cable tie Gather the cablesInsulating Fixing screw M5 SpacerSpeakers TY-SP42PM3W TY-SP42PWD3W10089 610 Left Speaker 89100 Right Speaker Safety PrecautionsDo not suspend the speakers Attach the sponges to the speakers Sponges For right For leftAttach the speakers to the Wide Plasma Display Secure the speakers in placeHook Slot Rear of Wide Plasma Display Bracket mounting screw Rear of Wide Plasma DisplayConnect the speaker cables Preparing the ends of the speaker cablesCentral P.O. Box 288, Osaka 530-8692, Japan

Related manuals

Manual 1 pages 52.7 Kb