Panasonic TY-ST42PT3S, TY-WK42PV1 Attach the sponges to the speakers, Sponges For right For left

Page 56

Instruction of the installation

Attach the sponges to the speakers.

•Attach the sponges to the surfaces which are in contact with the Display.

•Clean the surfaces before attaching the sponges.

Sponges

For right

For left

Attach the mounting brackets to the speakers.

Mounting brackets (right)

Mounting brackets (left)

Bracket mounting screws	Bracket mounting screws
Speaker (right)	Speaker (Ieft)

Sponge x 2

Mounting bracket (right) x 2

Mounting bracket (left) x 2

Bracket mounting Assembly screw (M4-10) x 8

7-3

Image 56

Contents Pedestal Other notes How to use this manualSome notes on how to read this manual Before installing Optional parts list Tools listAccessory list SpeakersWall stand Parts listPedestal Wall-hanging bracket angled Mobile standWall-hanging bracket vertical Speakers Points to note during installationCeiling unit Dimensions of the display unit Units mmPage Pedestal TY-ST42PT3S TY-ST42PT3KInstruction of the installation Assembling the pedestalAttaching the pedestal to the display unit ScrewsRear Fixing the display unit Fixing the display unit to a deskFront Fixing the display unit to the wall Wall stand TY-ST42PW1Installation diagram DescriptionAssembling the wall stand Fixing the insulating spacers to the display unit Provisionally tighten the fixing screwsDisplay unit face down Remove the screws and coversRemove the four screws Screw through and , then screw the four to the display unitAttaching the wall stand to the display unit Base of the display unit as shown in the illustrationHolding bracket Fixing screws left and right Lower the display into placeRemoving the display unit Mobile stand TY-ST42PF31020 40 5/32 610 24 820 89 3 33/64 400 15 3/4Then fix them from below using the four bolts Assembling the mobile standFixing the display unit to the stand Display unit as shown in the illustration belowFixing the wiring Mounting holes in the rear of the supportRemoving the display unit Wall-hanging bracket vertical TY-WK42PV1930 100 660 490 450 320 610 69.5 450 900 1020Installation diagram For Multi Screen 120Fixing the wall-hanging bracket to the wall 930 450 490Into the holes UnitRemove the four screws from the display Attaching the display unit to the wall- hanging bracket Notches Insultating spacerFixing screwsleft and right Bracket, and then lower the display unit into placeLift the display away from the wall-hanging bracket Fixing srews Lower insulating Left and right SpacerSpacers If UN Official Bracket is Used Wall-hanging bracket angled TY-WK42PR1450 900 1020 310930 100 660 490 450 Insert and fasten a M6 screw bolt into the center-top hole Adjusting the angle of the display fitting Tilt No tilt Stay5tilt 10tilt 15tilt 20tilt No tilt Screw bolts into the remaining five holesFixing the insulating spacers to the display Attaching the display unit to the wall- hangingbracket Fixing screws Insulating spacerWall-hanging bracket Fixing screws mountsFoxing screws Insulating spacer Left and right Lift the display unit slightlyCeling unit TY-CE42PS1431 Prepare the ceiling unit Assembling the ceiling unitFixing bolt M8-12 Ceiling unit Lower section Upper section Ceiling board Installation the ceiling unitInstalling to a wooden structureexample White line Hidden Side Quite los cuatro pernos Install the insulating spacers in the display unitPrepare the display Mount the display in the ceiling unit Insulating spacer NotchFixing screw M5 1 each Left and right sides DownwardConnecting pipe Angle Adjustment Hole positions Vertical Adjust the ceiling units directionAdjust the ceiling units angle Fixing bolt M8-20Cable tie Gather the cablesInsulating Fixing screw M5 SpacerSpeakers TY-SP42PM3W TY-SP42PWD3WDo not suspend the speakers Safety Precautions10089 610 Left Speaker 89100 Right Speaker Attach the sponges to the speakers Sponges For right For leftAttach the speakers to the Wide Plasma Display Secure the speakers in placeHook Slot Rear of Wide Plasma Display Bracket mounting screw Rear of Wide Plasma DisplayConnect the speaker cables Preparing the ends of the speaker cablesCentral P.O. Box 288, Osaka 530-8692, Japan

Related manuals

Manual 1 pages 52.7 Kb