Panasonic PT-L780E, PT-L780NTE manual Lamp unit replacement procedure, Turn off the power

Page 33

 

On-screen display

Lamp indicator warning

 

 

light

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Displayed for 30

 

 

 

More than 1 300 hours

seconds. Pressing any

 

 

 

button will clear the

The projector will enter

 

display.

 

Standby Mode and the

 

 

 

This display cannot be

red indicator lamp will

More than 1 500 hours

cleared at all, no matter

illuminate.

which button is pressed.

 

 

 

 

 

 

 

 

Lamp unit replacement procedure

NOTE:

BIf the lamp usage time has passed 1 500 hours (when LAMP POWER has been set to “HIGH”), the projector will switch to standby mode after approximately 10 minutes of operation. The steps ) to . on the next page should thus be completed within 10 minutes.

'Close the air outlet port, and then use a Phillips screwdriver to securely tighten the air outlet port fixing screws.

NOTE:

BBe sure to install the lamp unit and the air outlet port securely. If they are not securely installed, it may cause the protection circuit to operate so that the power cannot be turned on.

(Insert the mains plug into the mains socket and then press the MAIN POWER switch.

NOTE:

BIf the POWER indicator on the

projector does not illuminate red

when the MAIN POWER switch is

turned on, turn the MAIN POWER

switch off again and check that

the lamp unit and the air outlet

+Press the ENTER button and select the “LAMP RUN TIME” by pressing the F or G buttons.

OPTION

SHUTTER

 

 

OSD

OFF

ON

AUTO KEYSTONE

OFF

ON

RGB/YPbPr

RGB

YPbPr

RGB2 SELECT

INPUT

OUTPUT

BACK COLOR

BLUE

BLACK

FRONT/REAR

FRONT

REAR

DESK/CEILING

DESK

CEILING

LAMP POWER

LOW

HIGH

 

 

 

LAMP RUN TIME

 

1820 H

NEXT PAGE @

 

 

SELECT:[^][@]

ENTER:[ENTER]

ADJUST:[{][}]

ESC:[MENU]

,Press and hold the ENTER button for approximately 3 seconds.

Lamp Time Reset

Power OFF

OK

CANCEL

#Turn off the MAIN POWER switch according to the procedure given in “Turning off the power” on page 29, and then disconnect the mains plug from the mains socket and check that the area around the lamp unit has cooled down.

$Use a Phillips screwdriver to turn the air outlet port fixing screws at the back of the projector, and then open the air outlet port.

Air outlet port

Air outlet port fixing screws

%Use a Phillips screwdriver to loosen the two lamp unit fixing screws until the screws turn freely. Then hold the handle of the lamp unit and gently pull it out from the projector.

Lamp unit fixing screws

Handle

&Insert the new lamp unit while making sure that the direction of insertion is correct, and then use a Phillips screwdriver to securely tighten the lamp unit fixing screws.

port are securely installed. Then

turn the MAIN POWER switch

back on.

)Press the POWER button so that a picture is projected onto the screen.

*Press the MENU button to display the MENU screen, and select “OPTION” by pressing the I or H buttons.

OPTION

SHUTTER

 

 

OSD

OFF

ON

AUTO KEYSTONE

OFF

ON

RGB/YPbPr

RGB

YPbPr

RGB2 SELECT

INPUT

OUTPUT

BACK COLOR

BLUE

BLACK

FRONT/REAR

FRONT

REAR

DESK/CEILING

DESK

CEILING

LAMP POWER

LOW

HIGH

LAMP RUN TIME

 

1820 H

NEXT PAGE @

 

 

SELECT:[{][}]

ENTER:[ENTER]

ADJUST:[{][}]

ESC:[MENU]

The “Lamp Time Reset” will be displayed.

-Select “OK” by pressing the I or H buttons and press the

ENTER button.

NOTE:

BIf “CANCEL” is selected in step -, the operation for resetting the lamp time will be cancelled.

.Turn off the power.

 

This will reset the cumulative

 

usage time for the lamp unit to

 

zero.

 

Refer to steps % and & on page

 

29 for details on how to turn off

 

the power.

Others

 

64-ENGLISH

ENGLISH-65

Image 33
Contents Model No. PT-L780NTE LCD Projector Commercial UseDear Panasonic Customer Model number PT-L780NTE/PT-L780EImportant the Moulded Plug U.K. only Precautions with regard to safety ContentsInsert the mains plug securely into the mains socket Do not handle the mains plug with wet handsDo not place the projector into water or let it become wet Do not place liquid containers on top of the projectorDo not put your weight on this projector AccessoriesUse only the specified batteries Do not mix old and new batteriesPrecautions on handling Projector Back and bottom Location and function of each partProjector control panel Remote control unitPT-L780NTE only Connector panelUsing the remote control unit Wireless mouseLaser beam pointer Operating range Inserting the batteriesPin No Signal SignalConnections External viewComputer for Control use Sub 9-pin DVD player Male MonitorProjection methods Setting-upProjector position Projection distancesTurning on the power Turning off the powerStarting to use Menu screens On-screen menusMenu operation guide Using the freeze function Using the D.ZOOM digital zoomReturning a setting to the factory default FunctionAdjusting the picture White Balance R/G/B Adjusting the positionThen use the I or H button to Select StandardPosition Clock PhaseDOT Clock KeystoneChanging the display language Audio adjustmentOption settings Auto Power OFF WEB PasswordStatus Control KEYInstalling the lens Lens SelectRemoving the lens ET-LE20 for medium-distance projection ET-LE10 for short-distance projectionET-LE30 for long-distance projection Screen size Projection distance L Diagonal Height SH WidthLens Using the cable cover Short pin 1 and pin 9 when controllingPin assignment and control Using the Serial connector Remedy IndicatorsList of compatible signals About the automatic setup functionCleaning procedure Lamp unit replacement periodLamp unit replacement procedure Turn off the powerPress and hold the Enter button for approximately 3 seconds Before calling for service Before calling for service, check the following pointsProblem Possible cause Sync HD/SYNC SpecificationsTrademark acknowledgements Dimensions