Symphonic WF803 owner manual Hookups, Connecting to a TV Without A/V Terminals

Page 13

HOOKUPS

CAUTION:

¡Be sure to turn off the DVD/VCR COMBINATION UNIT and equipment to be connected. ¡Read through the operation manual for the equipment to be connected.

¡Be sure that the colors of the jacks and plugs match up when using VIDEO/AUDIO cables.

¡Be sure to keep the DVD/VCR COMBINATION UNIT connection cables separate from the TV antenna cable when you install the DVD/VCR COMBINATION UNIT, because it may cause electrical interference when you are watching television programs.

CONNECTING TO A TV WITHOUT A/V TERMINALS

1.Disconnect the AC power cord of the TV from the AC outlet.

2.Disconnect the antenna or cable from the TV.

3.Connect the antenna or cable to the ANT-IN jack of the DVD/VCR COMBINATION UNIT.

4.Connect the DVD/VCR COMBINATION UNIT to the TV using the RF cable.

5.Plug the AC power cords of the DVD/VCR COM- BINATION UNIT and TV into the AC outlets.

[VHF/UHF

[Indoor antenna]

[Back of the DVD/VCR]

combination antenna]

 

 

[Back of the

 

 

 

UHF/VHF combination TV]

 

OR

DVD/VCR

VCR RF cable

 

 

ANT-IN

(supplied)

 

 

AUDIO OUT

 

[Cable

box or satellite box] OR

L

UHF/VHF

R

AUDIO IN

From Cable or

ANT-OUTVIDEO OUT

VIDEO IN

Satellite Company

 

RF OUTPUT CHANNEL for DVD/VCR

1.Connect the DVD/VCR COMBINATION UNIT to a TV using RF cable (see above steps).

2.Select channel 3 on your TV.

3.Press PLAY.

¡If noise appears, change the RF output channel of the DVD/VCR COMBINATION UNIT to channel 4 by pressing PLAY on the VCR for 3 seconds during playback.

¡There is case that the RF output channel does not change by situation (For example, when you adjust tracking using

CHANNEL ( ) ).

In this case, stop the playback, and start the playback again. After that, press PLAY on the VCR for 3 seconds.

¡If there is a power failure or the DVD/VCR COMBINATION UNIT is unplugged for more than 30 seconds, the RF output channel setting will return to CH3.

Note to CATV system installer

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro- vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building, as close to the point of cable entry as practical.

CONNECTING TO A TV WITH A/V TERMINALS

 

DVD/VCR

VCR

 

 

DVD

 

Antenna/Cable signal

AUDIO OUT

 

S-VIDEO COMPONENT AUDIO

DIGITAL

ANT-IN

 

OUT

VIDEO OUT

OUT

AUDIO OUT

 

L

 

 

Y

 

 

A/V-compatible or

ANT-OUTVIDEO OUT

AUDIO IN

 

Cb

L

COAXIAL

 

R

 

 

wide screen TV

 

VIDEO IN

 

Cr

R

 

To ANT. IN

 

 

 

 

 

 

of TV

 

 

 

 

 

 

To VIDEO INPUT jack

To VIDEO OUT jack

 

 

 

 

To Right (red) and Left (white)

 

 

 

[Fig. 1]

To AUDIO INPUT jacks To AUDIO OUT jacks

 

 

 

Notes

¡Connect the DVD/VCR COMBINATION UNIT directly to a TV. If the A/V cables are connected into a VCR first, picture may be distorted due to the copy protection system.

– 13 –

EN

1L25

Image 13
Contents WF803 Laser Safety Important Safeguards Symbols Used in this Manual Supplied AccessoriesAbout Copyright Indice Table of ContentsPrecautions FeaturesPlayable Discs About the DiscsFollowing discs can be played back on this Operating Controls and Functions Press to select DVD mode for the remote control Light appears when a disc is in the DVD PlayerPress to access the VCR menu Press to enter DVD player setup modeConnect to a standard AC outlet to supply power to Press to select VCR mode for the remote controlUse to select VCR or TV position To watch TV or to view one program while recording anotherDVD Analog Audio OUT Jacks Loading the BatteriesDVD Mode VCR/DVD SwitchingConnecting to a TV with A/V Terminals Connecting to a TV Without A/V TerminalsHookups For TVs with S-VIDEO Input Jack Connecting to AN Analog Audio System Connecting to a Receiver with Dolby Digital DecoderAutomatic Channel SET UP SetupTo Preset the Channels Again To Select a Desired ChannelTo Change the ON-SCREEN Language Clock SET UPTo ADD/DELETE Channels Normal Playback Playback FunctionSearch Functions Auto Repeat PlaybackRecording Function Timer RecordingNormal Recording To Stop AN Automatic Timer PRO- Gram Already Started Hints for TimerTo CHECK, CORRECT, or Cancel AN Automatic Timer Program Copying a Video Tape Special FeaturesTo Monitor the Recording Playing a Disc General FeaturesAuto Rewind Basic PlaybackTitle Menu Disc MenuStep by Step Playback Fast FORWARD/REVERSE SearchTrack ZoomTitle / Chapter Search Time SearchProgram RepeatRepeat Title / Chapter Repeat TrackMP3 Playback Random PlaybackON-SCREEN Information Track SelectionSubtitle Language Stereo Sound ModeAudio Language Camera AngleParental Control Changing the ON-SCREEN DisplayParental Level ¡The elapsed and remaining Playing time of the currentMarker Setup Screen DVD SetupAudio Setting Display Setting Black Level Setting¡Be sure to press SETUP, or the setting will not work Virtual SurroundLanguage Setting Problem Corrective Action Troubleshooting GuideServicing MaintenanceSpecifications Panel Delantero Controles DEL Funcionamiento Y SUS FuncionesBotón Stop DVD Visión Trasera Modo VCR Cambio DE VCR/DVDPreparación ConexionesPreparación DE Reloj Reproducción DE UN DiscoReproduciendo UN DVD Video O UN CD Audio Pasos InicialesMemo Memo Memo H9402UD Customer Service North Street Teterboro, NJ