Symphonic CSDV840E owner manual Preset for Use, Turn on the unit for the first time, Clock Set Up

Preset for Use

Turn on the unit for the first time

VCR

VCR

1

Turn on the TV and set it to channel 3.

•If channel 3 is already occupied for broadcasting, see“RF Output Channel” section.

To Preset the Channel Again

1)Press the MENU button until the main menu appears.

2)Select "CHANNEL SET UP" by pressing the K or L button. Then, press the B but- ton.

3)Select "AUTO SET UP" by pressing the

K or L button. Then, press the B button. After scanning, the tuner stops on the low- est memorized channel.

4		CLOCK SET
	MONTH DAY		YEAR
or	0 3	/ 1 5	2 0 0 4
	HOUR MINUTE		AM/PM
	– –	: – –	– –
	Select the current year

2	POWER	Remote Control	TV Screen
		LANGUAGE SELECT
		B ENGLISH		[ON]
	or	FRANCAIS
Setup		ESPAÑOL
3				CH 01

AUTO SET UP

Do you connect the cable from the cable box or the satellite box to the DVD/VCR’s ANT IN jack?

YES

Yes Press the MENU button to exit

•Refer to “Hint for Cable Box or Satellite Box” section on

page 6. NO

No Please wait for a few minutes.

After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memo- rized in this unit by using the CHANNEL buttons.

•If "AUTO SET UP" appears on the TV screen again, check the cable connections. Then, press the B button once again.

Hint

•Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds.

To Change the On-Screen Language

1)Press the MENU button until the main menu appears.

2)Select "LANGUAGE SELECT" by press- ing the K or L button. Then, press the B button.

3)Select "ENGLISH" , "FRANCAIS" or "ESPAÑOL" by pressing the K or L but- ton. Then, press the CLEAR/C.RESET button.

Hint

•If you accidentally select Spanish or French and need English: Press the MENU button and choose SELEC.

IDIOMA, or SELECTION LANGUE. Press the B button, and select ENGLISH. Finally, press the CLEAR/C.RESET button.

Clock Set Up

	VCR
VCR
1 MENU	-MENU-

TIMER PROGRAMMING

AUTO REPEAT [OFF]

CHANNEL SET UP

BCLOCK SET LANGUAGE SELECT

or	• If the clock is not set, the
	CLOCK SET screen
	appears when you press
	the MENU button. In this
	case, go to step [2].

2		CLOCK SET
or	MONTH DAY		YEAR
	0 3	/ – –	– – – –
	HOUR MINUTE		AM/PM
	– –	: – –	– –
	Select the current month

5	CLOCK SET
MONTH DAY		YEAR
0 3	/ 1 5 MON 2 0 0 4
or
HOUR MINUTE		AM/PM
0 5	: – –	– –
Select the current hour

6	CLOCK SET
MONTH DAY		YEAR
0 3	/ 1 5 MON 2 0 0 4
or
HOUR MINUTE		AM/PM
0 5	: 4 0	– –
Select the current minute

7	CLOCK SET
MONTH DAY		YEAR
0 3	/ 1 5 MON 2 0 0 4
or
HOUR MINUTE		AM/PM
0 5	: 4 0	P M AM
		B PM
Select “AM” or “PM”

8To exit the CLOCK SET screen.

Hint

• To go back one step, press the s button

(during the steps [2] to [7].)

• Your clock setting will be lost if either there

is a power failure or this unit has been

To Select a Channel

You can select a channel by directly entering channel using the Number but- tons on the remote control.

Notes for using the Number buttons:

•When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number.(For example: 117, press 1,1,7)

•You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on).

3		CLOCK SET
	MONTH DAY		YEAR
or	0 3	/ 1 5	– – – –
	HOUR MINUTE		AM/PM
	– –	: – –	– –
	Select the current day

unplugged for more than 30 seconds.

– 10 – EN