Sharp PN-E702, PNE702 operation manual 49 E

Page 49

■ SNMP

You can configure settings related to SNMP.

SNMP SETTING

Set whether to enable or disable SNMP.

VERSION

Set the version of the SNMP to be supported.

COMMUNITY NAME 1 to 3

Set the name of the community required for the access.

USER 1 to 3

Set the user name, password, authentication method and other options required for access.

TRAP SETTING

Set whether to enable or disable the trap function.

When this function is enabled, a trap will be sent when the monitor is turned on.

TRAP SETTING OF AUTHENTICATION ERROR

Set whether the trap function sends a notification when authentication fails.

TRAP ADDRESS & PORT

Set the destination address and port number of the notification sent by the trap function.

Controlling the Monitor with a PC (LAN)

Caution

After you set SNMP, click [Switch the main power of monitor off and on now.] or turn off the monitor and then turn it on again with the main power switch. When the monitor restarts, wait about 30 seconds and then start the next operation.

If the IP address is changed while the SNMP function is operational, turn off the monitor and then turn it on again with the main power switch.

TIPS

Depending on the SNMP settings, a short delay may occur before the SNMP is usable. (About 2 minutes)

Up to 16 alphanumeric letters and symbols can be used for the community name, user name and password.

■ SERVICE & SUPPORT (URL INFORMATION)

You can display a specific URL in the URL INFORMATION field on the INFORMATION screen when an error occurs in the monitor. (See page 45.)

URL INFORMATION

Enter the URL to display on the INFORMATION screen when an error occurs on the monitor.

Up to 64 alphanumeric characters or symbols can be used.

CONDITION

Specify the condition to display the URL.

CONFIRMATION

The home page of the specified URL is displayed.

You can check whether the URL you entered is correct.

TIPS

It is also possible to specify the message text, such as the name of a contact or a telephone number, to be displayed instead of the linked URL.

49 E

Image 49
Contents PN-E702 GREEN-AND-YELLOW For Customers in U.KBlue BrownImportant Information Refer Servicing to Qualified Service PersonnelInformation on Disposal for Business Users Information on Disposal for Users private householdsEuropean Union Other Countries outside the EUDear Sharp Customer Safety Precautions Tips and Safety Instructions For the monitor in portrait orientation For the monitor in landscape orientationDo not place the monitor on a device which generates heat Supplied Components ContentsNFront view Part NamesNRear view Signal transmitter NRemote control unit Part NamesPower button See Mute button See 11 EConnection with a PC or AV equipment Connecting Peripheral Equipment13 E Connecting Peripheral EquipmentBinding Cables Connecting the Power CordRemoving the Handles Handles can be removedInstalling the batteries Preparing the Remote Control UnitRemote control operation range 15 ETurning on the main power Turning Power On/OffTurning power on/off Main power switchNOperation mode Disabling power on/off operationsNDate/time setting Turning Power On/OffMute Basic OperationMenu Display19 E Basic Operation NSwitching the screen sizeWide Zoom Normal Dot by DotDisplaying the menu screen Menu ItemsNExample of operation NMenu screen displayMenu item details 21 ENSCREEN Menu Items NPICTUREMenu Items NSETUPNAUDIO NOPTION 23 ENMULTI NPIP/PbyP 25 EMenu Items NDual screen display Setting procedure NZOOM2 Special SettingSet using the Multi menu Menu Items NEnlarge27 E PowerNSCHEDULE DAY of the WeekNAutomatic adjustment Adjustments for PC screen displayNScreen display for adjustment 29 E Controlling the Monitor with a PC RS-232C Communication procedurePC connection Communication conditionsNResponse code format 31 ENID numbers VOLM0030 002VOLM0020 ← OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ←33 E Setting of the Gamma user dataPower control/Input mode selection RS-232C command tableHow to read the command table Command Command field See DirectionControlling the Monitor with a PC RS-232C Screen menu 35 EControlling the Monitor with a PC RS-232C Picture menu 37 E Setup menuControlling the Monitor with a PC RS-232C Audio menu Controlling the Monitor with a PC RS-232C Option menu 39 E Image Position Epos settingControlling the Monitor with a PC RS-232C Multi menu Landscape orientation Portrait orientationControlling the Monitor with a PC RS-232C PIP/PbyP menu Initialization/Functional Restriction Setting Function menu41 E Commands for setting of the Gamma user dataControlling the Monitor with a PC RS-232C Others Controlling the Monitor with a PC LAN Settings to connect to a LANTo set on the monitor 43 E Default Gateway 0.0To set from a PC Controlling the Monitor with a PC LANControlling with a PC See pages 45 to 49 for details on each settingBasic operation If the Dhcp Client is set to OFF, specify an IP address45 E Standby mode, Power on is the operation availableInformation about this monitor appears If the Dhcp Client is set to OFF, specify the subnet mask User Name / PasswordDNS Server Accept IP Address47 E Recipient E-MAIL Addresses Attach the log file to a TEMPERATURE/HARDWARE error e-mailCondition Confirmation49 E Troubleshooting 51 E TroubleshootingNProduct Specifications SpecificationsNPower management NDimensional Drawings Specifications53 E NDDC plug and playNCompatible signal timing AV Specifications NCompatible signal timing PC55 E Mounting Precautions For Sharp dealers and service engineers PN-E702 Me EN11K1