Sharp PNE702, PN-E702 operation manual NProduct Specifications

Specifications

nProduct Specifications

Model					PN-E702
LCD component					70" Class [69-1/2 inch (176.6cm) diagonal] TFT LCD
Max. resolution				(pixels)	1920 x 1080
Max. colors					Approx. 1.06 billion colors
Pixel pitch					0.802 mm (H) × 0.802 mm (V)
Viewing angle					176° right/left/up/down (contrast ratio ≥ 10)
Screen active area				inch (mm)	60-9/16 x 34-1/16 (1538.9 x 865.6)
Computer input signal					Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75 Ω]
Sync signal					Horizontal/vertical separate (TTL: positive/negative), Sync-on-green,
					Composite sync (TTL: positive/negative)
Video color system					NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM
Plug and play					VESA DDC2B
Power management					VESA DPMS, DVI DMPM
Input terminals		PC/AV	Digital		HDMI x 1
		PC	Analog		Mini D-sub 15 pin, 3 rows x 1
		Audio			3.5 mm mini stereo jack x 1
		Serial (RS-232C)			D-sub 9 pin x 1
	When PN-ZB01	PC/AV	Digital		DVI-D 24 pin (HDCP compatible) x 1
	(optional) is
		PC	Analog		BNC *1*2 x 1
	attached
		AV	Composite video		BNC x 1
			S-video		x 1
			Component		BNC (Y, Cb/Pb, Cr/Pr) *1 x 1
		Audio			RCA pin (L/R) x 2
Output terminals		Audio			RCA pin (L/R) x 1
		Serial (RS-232C)			D-sub 9 pin x 1
	When PN-ZB01	PC/AV	Digital		DVI-D 24 pin x 1
	(optional) is	External speaker			7 W + 7 W [6 Ω]
	attached
LAN terminal					10 BASE-T/100 BASE-TX
[When PN-ZB01 (optional) is attached]
Speaker output					7 W + 7 W
Power requirement					AC 100 V - 240 V, 2.8 A, 50/60 Hz
Operating temperature *3					32°F to 104°F (0°C to 40°C)
Operating humidity					20% to 80% (no condensation)
Power consumption					235 W / 1.0 W / 1.0 W
(Maximum / input signal waiting mode *4 / standby
mode *5)
Power consumption					240 W
[When PN-ZB01 (optional) is attached]
Dimensions (excluding protrusions)				inch (mm)	Approx. 63-9/16 (W) x 3-15/16 (D) x 37-5/16 (H) (1,615 x 100 x 947)
Weight				lbs. (kg)	Approx. 110.2 (50)
Weight [PN-ZB01 (optional)]				lbs. (kg)	Approx. 1.102 (0.5)

*1 Cannot be used simultaneously.

*2 Does not support plug and play.

*3 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such cases, please check the temperature condition specified by the optional equipments.

*4 When AUTO INPUT CHANGE is set to OFF.

*5 When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

E52