Sharp PNE702, PN-E702 Controlling the Monitor with a PC LAN, Settings to connect to a LAN

Page 42

Controlling the Monitor with a PC (LAN)

When the PN-ZB01 (optional) is attached, your monitor can be connected to a LAN allowing you to control it from a PC on the LAN.

You can also configure the monitor to send e-mail notification when it has a problem.

The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through).

Network (LAN)

LAN terminal Hub

LAN cable (commercially available, straight)

TIPS

•You must assign an IP address to the monitor by following the procedures in “Settings to connect to a LAN”. (See the description on the right.)

•Your PC must be installed with Internet Explorer (version 7.0 or later).

•To control the monitor via LAN, set RS-232C/LAN SELECT to LAN. (See page 23.)

•You cannot use RS-232C and LAN control simultaneously.

Initializing personal information

•When the PN-ZB01 (optional) is attached, personal information such as e-mail addresses can be registered in the monitor. Before transferring or disposing of the monitor, initialize all settings by selecting ALL RESET 1. (See page 29.) Note that ALL RESET 2 will not initialize e-mail addresses and other settings.

Settings to connect to a LAN

Set the monitor’s IP address and subnet mask to match the settings of your LAN.

These settings can be made on either the monitor or a PC connected to the monitor.

The settings depend on the configuration of your LAN. Ask your LAN administrator for details.

■ To set on the monitor

Set RS-232C/LAN SELECT on the SETUP menu to LAN, and then set the LAN SETUP options. (See page 23.)

After setting each item, select SET and press MENU .

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON.

To set the address manually, set this to OFF.

IP ADDRESS

If the DHCP CLIENT is set to OFF, specify an IP address.

Press or to select items, and press or to change the values.

SUBNET MASK

If the DHCP CLIENT is set to OFF, specify the subnet mask.

Press or to select items, and press or to change the values.

DEFAULT GATEWAY

If the DHCP CLIENT is set to OFF, specify the default gateway.

If you are not using a gateway, specify “0.0.0.0”.

Press or to select items, and press or to change the values.

RESET

Resets the values of the LAN settings to the factory preset values.

Select ON and then press MENU .

TIPS

•When the IP address is set manually, the IP addresses of the monitor connected to the RS-232C output terminal and the daisy chain of connected monitors that follows can be assigned automatically. (See page 23.)

E42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents PN-E702 Blue For Customers in U.KGREEN-AND-YELLOW BrownRefer Servicing to Qualified Service Personnel Important InformationEuropean Union Information on Disposal for Users private householdsInformation on Disposal for Business Users Other Countries outside the EUDear Sharp Customer Safety Precautions Tips and Safety Instructions For the monitor in landscape orientation For the monitor in portrait orientationDo not place the monitor on a device which generates heat Contents Supplied ComponentsPart Names NFront viewNRear view Power button See Mute button See NRemote control unit Part NamesSignal transmitter 11 EConnecting Peripheral Equipment Connection with a PC or AV equipmentConnecting Peripheral Equipment 13 ERemoving the Handles Connecting the Power CordBinding Cables Handles can be removedRemote control operation range Preparing the Remote Control UnitInstalling the batteries 15 ETurning power on/off Turning Power On/OffTurning on the main power Main power switchNDate/time setting Disabling power on/off operationsNOperation mode Turning Power On/OffMenu Basic OperationMute DisplayWide Zoom Normal Basic Operation NSwitching the screen size19 E Dot by DotNExample of operation Menu ItemsDisplaying the menu screen NMenu screen displayNSCREEN 21 EMenu item details Menu Items NPICTURENSETUP Menu ItemsNAUDIO 23 E NOPTIONNMULTI 25 E NPIP/PbyPMenu Items NDual screen display Set using the Multi menu NZOOM2 Special SettingSetting procedure Menu Items NEnlargeNSCHEDULE Power27 E DAY of the WeekAdjustments for PC screen display NAutomatic adjustmentNScreen display for adjustment 29 E PC connection Communication procedureControlling the Monitor with a PC RS-232C Communication conditions31 E NResponse code formatNID numbers VOLM0020 ← 002VOLM0030 OK 002 IDLK0000 ← Wait ← OK 002 ← VOLM0010 OK 001 ←Setting of the Gamma user data 33 EHow to read the command table RS-232C command tablePower control/Input mode selection Command Command field See Direction35 E Controlling the Monitor with a PC RS-232C Screen menuControlling the Monitor with a PC RS-232C Picture menu Setup menu 37 EControlling the Monitor with a PC RS-232C Audio menu Controlling the Monitor with a PC RS-232C Option menu Controlling the Monitor with a PC RS-232C Multi menu Image Position Epos setting39 E Landscape orientation Portrait orientationInitialization/Functional Restriction Setting Function menu Controlling the Monitor with a PC RS-232C PIP/PbyP menuCommands for setting of the Gamma user data 41 EControlling the Monitor with a PC RS-232C Others Settings to connect to a LAN Controlling the Monitor with a PC LANTo set on the monitor To set from a PC Default Gateway 0.043 E Controlling the Monitor with a PC LANBasic operation See pages 45 to 49 for details on each settingControlling with a PC If the Dhcp Client is set to OFF, specify an IP addressStandby mode, Power on is the operation available 45 EInformation about this monitor appears DNS Server User Name / PasswordIf the Dhcp Client is set to OFF, specify the subnet mask Accept IP Address47 E Condition Attach the log file to a TEMPERATURE/HARDWARE error e-mailRecipient E-MAIL Addresses Confirmation49 E Troubleshooting Troubleshooting 51 ESpecifications NProduct Specifications53 E NDimensional Drawings SpecificationsNPower management NDDC plug and playSpecifications NCompatible signal timing PC NCompatible signal timing AV55 E Mounting Precautions For Sharp dealers and service engineers PN-E702 Me EN11K1
Top Page Image Contents