Quick guide
Initial auto installation
When the TV is powered on for the first time after purchase, the initial auto installation wizard appears. Follow the menus and make the necessary settings one after another.
Confirm the following before turning on the power
EIs the antenna cable connected? E Is the AC cord plugged in?
1Press <on the TV.
NOTE
•If you turn off the power on the TV while performing a channel search in Step 5, the initial auto installation wizard may not appear. The auto installation function allows you to execute the installation again from “Setup” > “View setting” (Page 40).
•The initial auto installation wizard will abort if you leave the TV unattended for 30 minutes before searching for channels in Step 6.
•Selecting menu of "Digital Search" or "Analogue Search" may not be displayed in some country.
Checking signal strength and channel strength (DTV only)
• The initial auto installation wizard appears.
2Setting the OSD language.
Press a/b/c/dto select the desired language, and then press ?.
3Selecting the location of the TV.
Press c/dto select where you will use this TV, and then press ?.
HOME:
•Settings are optimised for normal home viewing and energy efficiency.
•“STANDARD” will be the default value for the “AV mode” setting.
If you install a DTV antenna for the first time or relocate it, you should adjust the alignment of the antenna to receive a good reception while checking the antenna setup screen.
1Go to “HOME” > “TV Menu” > “Setup” > “View setting” > “Channel settings” > “Antenna setup- DIGITAL”.
EChecking signal strength
2Press a/bto select “Signal strength”, and then press ?.
Supply voltage |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Signal strength |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Channel strength | CH No. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
| Signal strength |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Current |
|
|
|
|
|
| Max. |
|
|
|
| |||||||||||||||
|
| 97 |
|
|
| 97 |
| |||||||||||||||||||||
| Quality |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
| |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Current |
|
|
|
|
|
| Max. |
|
|
|
| |||||||||||||||
|
| 99 |
|
|
| 99 |
| |||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
STORE:
•Settings are designed for maximum impact in retail store displays.
•“DYNAMIC (Fixed)” will be the default value for the “AV mode” setting. If the “AV mode” is changed, the TV will automatically switch back to “DYNAMIC (Fixed)” when there is no operation using the TV or remote control unit for 30 minutes.
•The confirmation screen pops up only when selecting “STORE”. Press c/dto select “Yes” or “No”.
NOTE
•STORE: A demonstration image will be displayed after initial auto installation is completed. If you have chosen “STORE” by mistake, go to “Setup” > “View setting” > “Reset” > select “HOME” again.
4Setting the country.
Press a/b/c/dto select your country or area, and then press ?.
•This setting screen only appears during the initial auto installation.
NOTE
•DTV concerned menu may not displayed in some country.
5Press c/dto select “Digital Search” or “Analogue Search”, and then press ?.
6The TV searches for, sorts and stores all the receivable TV stations according to their settings and the connected antenna.
•To abort the initial auto installation in progress, press
C.
EChecking channel strength
3Press a/bto select “Channel strength”, and then press ?.
•You can input a specified frequency band using the
Supply voltage | Frequency | MHz | |
Signal strength | |||
|
| ||
Channel strength | CH No. |
| |
| Signal strength |
|
Current 97 Max. 97
Quality
Current 99 Max. 99
4Position and align the antenna so that the maximum possible values for “Signal strength” and “Quality” are obtained.
NOTE
•The values of “Signal strength” and “Quality” indicate when to check the appropriate alignment of the antenna.
Supplying power to the antenna (DTV only)
You can supply power to the antenna in order to receive digitally/terrestrially broadcast stations after connecting the antenna cable to the antenna terminal on the rear of the TV.
1Go to “HOME” > “TV Menu” > “Setup” > “View setting” >“Channel settings” > “Antenna setup- DIGITAL” >“Supply voltage”.
2Press c/dto select “On”, and then press ?.
16