Sylvania 6719DG owner manual Channel SET UP, Mpaa Rating SET UP, Change Access Code, TV Operation

B MPAA RATING SET UP

4Use [K / L] to point to your

desired item, then press		G	[VIEW]
[ENTER] to select "BLOCK"		PG	[VIEW]
		B R	[BLOCK]
		PG–13	[VIEW]
or "VIEW".		NC–17	[BLOCK]
		X	[BLOCK]
Selection	Rating Category	Explanations
G	General Audience
PG	Parental Guidance suggested.
PG-13	Unsuitable for children under 13

RRestricted; under 17 requires acco- mpanying parent or adult guardian

NC-17 No one under 17 admitted
X	Mature audience only

5Press [SET-UP]to exit the menu.

C CHANGE ACCESS CODE

4 Use the Number buttons to

enter your desired access

code in the "NEW CODE",	NEW CODE
		X X X X
then enter the same code in
the "CONFIRM CODE". When	CONFIRM CODE
completed, the menu will		_ _ _ _
return to "V-CHIP SET UP".

5Press [SET-UP]to exit the menu.

NOTE:

•Your personal access code will be erased and will return to the default (0000) when a power failure occurs or when you turn off the power using a wall switch. If you forget the code, unplug the power cord for 10 seconds to restore the access code to 0000.

AND SETTINGS TV/VCR SECTION

CHANNEL SET UP
Channel presetting is necessary at the start or in case you moved the TV to a different area.		TV/VCR
AUTO CHANNEL PROGRAMMING	ADDING/DELETING CHANNELS

TV OPERATION

1 Press [SET-UP].

	- TV/VCR SETUP -
Use [K / L] to point to	TIMER PROGRAMMING
	SETTING CLOCK
	B CHANNEL SET UP
"CHANNEL SET UP", then	USER’S SET UP
	V-CHIP SET UP
press [ENTER].	LANGUAGE [ENGLISH]
	CAPTION [OFF]
	ZERO RETURN
	TIME SEARCH
2 Use [K/ L] to point to "AUTO	INDEX SEARCH
	– CHANNEL SET UP –
CH PROGRAMMING", then	ADD / DELETE CH (CATV)
press [ENTER].	B AUTO CH PROGRAMMING

The tuner scans and memorizes all the active channels in your area.

You can add channels that was not memorized due to the bad reception status and also delete chan- nels you no longer receive or seldom watch.

1 Press [SET-UP].	- TV/VCR SETUP -
	TIMER PROGRAMMING
Use [K / L] to point to	SETTING CLOCK
	B CHANNEL SET UP
"CHANNEL SET UP", then	USER’S SET UP
	V-CHIP SET UP
press [ENTER].	LANGUAGE [ENGLISH]
	CAPTION [OFF]
	ZERO RETURN
	TIME SEARCH
2 Use [K / L] to point to	INDEX SEARCH
	– CHANNEL SET UP –
"ADD/DELETE CH", then	B ADD / DELETE CH (CATV)
press [ENTER].	AUTO CH PROGRAMMING

3When the scanning is comple- ted, the lowest memorized channel is displayed.

If "NO TV SIGNALS" appears on the TV screen, check the antenna connection and try again.

NOTES:

CH 15

<EXAMPLE>

NO TV SIGNALS

3 Use the Number buttons or
[CH. K / L] to select your
desired channel number.	08
(You can also use [K / L] to	ADD / DELETE
enter it.)
• Refer to page 9 on how to use	(Example: CH8)
the Number buttons.

•The unit may recognize CATV channels to be TV channels if reception condition is poor. In this case, check the antenna connection and try "AUTO CH PROGRAMMING" again.

•Auto channel programming is NOT necessary when connected to a cable box or satellite box. Just select the channel for cable box or satellite input (ex. CH3 or CH4) on the unit, then select your desired channel on the cable box or satellite box.

4Press [ENTER] repeatedly. The channel number changes to red (deleted) or blue (added) every time you press the button.

• To delete another channel, repeat steps 3 to 4.

5Press [SET-UP]to exit the menu.

NOTE:

•To confirm that channel(s) has been deleted or added, select it (them) using [CH. K / L].

13

EN