TechniSat 1 manual Switch DiSEqC on or off, Setting the switching matrix and the LNB properties

Page 14

The following adjustments can be made in this sub-menu:

5.4.1 Switch DiSEqC on or off

DiSEqC (Digital Satellite Equipment Control) is a digital control signal used to control and switch DiSEqC-compatible components via the antenna cable.

If your external unit is equipped with DiSEqC components, you must switch on the DiSEqC- control:

>Make adjustments in this line by means of the key OK DiSEqC on or off.

Since only one LNB can be addressed when the DiSEqC control is switched off, the menu is restricted to the configuration of a single LNB.

5.4.2Setting the switching matrix and the LNB properties

The menu lists the four switching criteria of the DiSEqC control.

Your receiver has been pre-programmed, so that ASTRA will be received in switch position A/A and Eutelsat in switch position B/A of a multiswitch. If the switching matrix of your recep- tion equipment be configured differently, or if it is set to receive other satellites, you can

make the following settings/adjustments in your receiver.

>Use the arrow up/down keys dto select the DiSEqC switch position (1-4) that you want to allocate to a particular satellite (e.g. A/B 3 No Satellite), by marking this line in blue.

>Confirm by pressing OK.

A list of various satellites will now be displayed.

>Use the arrow up/down keys to mark the satellite selected.

The arrow up/down keys will move the marker up or down one line at a time, while using the Parrow left/right keys will jump to the previous or next page.

If the satellite you are looking for is not specifically listed, select one of the spare posi- tions, marked as User1 to User 14.

>Confirm by pressing OK.

The selected and marked satellite will now be inserted and shown at the previously marked position in the menu >Settings>LNB.

Continue to work your way through the Menu >Settings>LNB, until the data in this menu

corresponds with that of your reception unit. Any switching criteria not required should be set to the position No Satellite.

5.4.3 Additional settings

Now that you have adjusted the switching matrix of your DVB receiver to correspond with your reception unit, you should now check the additional parameters of your reception unit, and, where necessary, make further corrections.

>Use the arrow left/right keys to move the marker to the column LNB-Test.

>Now use the arrow up/down keys, to mark the field Continue.in the line in which you want to check or alter the settings.

>Confirm by pressing OK.

The menu >LNB>Check will now be displayed, showing the DiSEqC setting selec- ted (e.g. A/A 1).

14

Image 14
Contents Timer DigiBox1Remote control unit MONO1/MONO2Table of contents Page Left/right Safety notes Please read this firstImportant operating instructions Operational breaksDisposal instructions Necting the DVB receiver satellite installation Connections OSD Language InstallationBasic settings Country Parental control settingTime difference GMT hrs Picture/image format of TV set Audio/Video settingsLanguage Audio signal SCART-ModeLNB-Setting/Adjustment of external unit/satellite selection Additional settings Switch DiSEqC on or offSetting the switching matrix and the LNB properties Page Programme selection Switching on and offOperation Volume control Going back to previous programme viewed Switching between TV and RadioSelecting a different language Displaying clock and programme informationElectronic Programme Guide Transponder InformationTeletext Audio-Video InformationProgramme preview for next few days TimerSwitching EPG off EPG InformationManual Programming/Changing timer settings Page Selecting a programme list Configuring programme listsChanging the basic programming Important NoteSelect user list Entering programmes in the programme listSelecting programmes Entering into the user programme listSorting programmes Blocking programme access Parental control featureDeleting programmes Deleting from user listProgramme Search Cancelling blocking of individual programmesChanging the PIN Satellite Transponder After the scan Restore default basic programming/ Delete allManual Search Activating default setting System configuration Technical TermsLNB/LNC Low Noise Block converter Frequency rangeIntermediate Frequency if Modulation at 22 KHzTechnical Data Audio Parameters Input analogue Audio decodingMemory capacity Output analogueRemote control system RC-5 LNB Power supplyTimer Power supply Power supply switch Power consumptionTroubleshooting Guide Problem Possible cause SolutionDear customer For programme slot TV/Radio switchingBrief instructions for daily use Then For programme slot Then 3, then