Panasonic NV-SJ260 Setting the Remote Control to Operate Your TV, TV Operation

Page 6

Setting the Remote Control to Operate Your TV

This setting procedure allows you to operate the TVs of most brands using the remote control supplied with this VCR.

≥Some TV models cannot be operated with this remote control.

1Set the VCR/TV switch O to “TV”.

2Look up your TV’s manufacturer in the list of TVs compatible with the VCR’s remote control on the next page.

3While keeping the TV-ON/OFF button 1 pressed, use the Numeric buttons 2 to enter the manufacturer’s code. If there is more than one code listed for that manufacturer, try the first code.

Be sure to enter the code in two digits. Example: 01

4Check whether you can operate the TV correctly with the VCR’s remote control.

If the TV cannot be operated properly:

In step 3, enter the other code listed for that manufacturer and repeat step 4.

TV Operation

The explanations below show you what functions individual buttons have when the VCR/TV switch O is set to “TV”.

°°1 TV-ON/OFF button

To switch the TV on from standby mode (OFF) or vice versa.

On some TVs it is only possible to switch the TV to standby mode (OFF) with this button, but not on. In this case, try to turn the TV on with one of the following buttons:

Numeric buttons 2

AV button 3

Channel button N

°°2 Numeric buttons

To select the programme positions (1–99) on the TV.

°°3 AV button

To select the desired AV input on the TV.

°°N Channel button

To select the desired programme position (TV station) on the TV.

°°V Teletext buttons

If your TV is equipped for Teletext reception, you can use these buttons to change the teletext information displayed on the screen and select desired information. For details, refer to your TV’s operating instructions.

°°W TV ASPECT button

To switch the screen format between the wide-screen and other formats.

°°X VOLUME button

To adjust the volume of the TV.

°°Y TV/TEXT button

To switch between normal TV mode and teletext mode.

The 3 Methods for Switching

to the AV Input on Your Panasonic TV

Your Panasonic TV uses one of three different methods for switching between TV reception and the AV input(s). Perform the operations steps listed for the switching methods A, B and C below to determine which one your Panasonic TV uses.

A1 Set the VCR/TV switch O to “TV”.

2 Press the AV button 3 to switch to the AV Input. Each press of the AV button 3 switches between “TV reception” and “AV Input(s)”.

B1 Set the VCR/TV switch O to “TV”.

2 Press the AV button 3.

Colour bars for selecting the AV Input appear on the TV screen.

3 Follow the instructions displayed on the TV screen to select the desired AV Input from the displayed colour bars for the AV Input by pressing the corresponding colour button J (red) :, DATEi (green) ;, ONi (yellow) G or OFFi (blue) F on the remote control.

C1 Set the VCR/TV switch O to “TV”.

2 Press the AV button 3.

The last previously selected AV Input indication appears on the TV screen. The indications for selecting another AV Input also appear,

but they disappear a few seconds later.

3 Before the indications for selecting another AV Input disappear, press the I button :, DATEj button ;, ONj button G or OFFj button F to select the desired AV input.

With the following four buttons, you can move and select as follows:

I :: Move left

DATEj ;: Move down

ONj G: Move up

OFFj F: Move right

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents NV-SJ260 Series Contents Dear CustomerControls and Components VCRIf the Sliding Cover of the Remote Control Becomes Detached Preparing the Remote ControlInserting Remote Control Batteries VCR OperationDo not Remove Outer Cover RemarksSetting the Remote Control to Operate Your TV TV OperationList of TVs Compatible With the VCR’s Remote Control Manufacturer CodeHints To Set Up this VCR with a TV Already Preset Download FunctionTo Simultaneously Set Up this VCR with a New TV UsePage To Confirm that the TV Stations Have Been Auto Setup FunctionTuned Correctly by the Auto Setup FunctionDisplay Playback To Stop Playback Automatically Playback Off Timer Function To Eject the Video Cassette Using the Remote ControllerConvenient Automatic Functions Recording To Pause RecordingTo Display the Approximate Remaining Tape Time Linked Timer Recordings with a Digital Receiver To Prevent Accidental Erasure of Recorded ContentsPress the OK button S to conclude the settings Timer RecordingTo Suspend the Timer Recording Standby Mode To Programme with the On Screen Display OSDTo Programme with ShowView Function Press the OK button S to display the programmed contentPress the OK button S again to conclude Settings Press the Numeric buttons 2 to enter the ShowView numberTo Check the Contents of Timer Recording Programmings Other Timer Recordings and Convenient FunctionsSetting the Recording Date/Days To Change a Timer Recording ProgrammingTo Cancel the Programme List Search To Cancel the Programming of a Timer RecordingTo Check the Total Timer Recording Programming Time PreparationSearch Functions To Cancel the Index Search or to Stop PlaybackTo Cancel the Intro-Jet Scan or to Stop Playback OperationAssemble Editing Connecting the VCR to a DecoderEditing To Connect the VCR to a DecoderSatellite receiver not supplied Pin Scart socket To Enter or Change the Name of a TV Station List of TV Reception Channels To Obtain the Best Tuning ConditionTo Enter Newly Available TV Stations To Change the Channel Number of an Already Tuned TV StationTo Preset Pay TV Stations To Change the Type of Video System Colour TV systemTo Restart the Auto Setup To Restart the DownloadTo Return the VCR to the Shipping Condition Setting the VCR’s Clock To Manually Adjust the ClockTo Activate the Automatic Time Correction Function Video system colour TV system Tape length indicator Other Convenient Functions Various SettingsSettings for the Main Menu Item Display TV station nameSettings for the Main Menu Item Functions DimmedLanguage Setting Country SettingTo Set the Remote Control Mode Crystal View Control CVC GlossaryVPS Video Programme System/ PDC Programme Delivery Control Programming ShowView Changes Non MethodMessage Message appears when Link FunctionPin Scart Socket AV1 Scart Socket for Q Link connection√ The VCR Does Not Work Correctly Before Requesting Service√ On Screen Display Messages √ Playback Does Not Work Properly√ The Remote Control Does Not Work Correctly √ Recording Is Not Possible or Does Not Work ProperlyPrecautions Adjusting the Playback PictureIf the Still Picture Scrolls Up or Down V-Lock Adjustment To Return to Auto TrackingCleaning the VCR Avoid sudden changes in temperatureKeep the VCR away from high temperatures Avoid humidity and dustSpecifications
Top Page Image Contents