Panasonic NV-SJ260 operating instructions Connecting the VCR to a Decoder, Assemble Editing

Page 22

Editing

Assemble Editing

The assemble editing function makes it easy to record the picture and sound of virtually any number of scenes or programmes in succession.

Assemble editing from an external source, for example from a video movie camera, can be performed in the same way.

Recording unit (this VCR)

a b

Video movie camera or other VCR

Preparations

≥Connect a video movie camera or a VCR to this VCR with a 21-pin Scart cable, as shown in the illustration.

≥Display the VCR picture on the TV.

≥Insert the cassette on which the assemble editing is to be performed, and make sure that its erasure prevention tab is not broken out.

≥Set the VCR/TV switch O to “VCR”.

≥Press the INPUT SELECT button 3 to select the AV Input (external input) “A1” or “A2” according to the socket(s) on the VCR to which the source unit has been connected.

A1: When connected to the AV1 21-pin Scart socket a

A2: When connected to the AV2 21-pin Scart socket b

≥Make sure that “AV2” is set to “EXT”. (See page 30.)

Operations

1Press the Play button I to start playback.

2At the point where you want to join a new scene, press the Pause/Slow button 7 to put it in the still playback mode.

3Press the REC button J to put it in the recording pause mode.

4Start playback on the source unit and search for the point from which you want to record (copy) onto this VCR.

5When that point is reached, press the Pause/Slow button 7 again to start recording the new picture and sound from the playback unit.

6To record (copy) additional scenes, press the Pause/ Slow button 7 to put this VCR in the recording pause mode and then perform steps 4 and 5 again.

7At the point where you want to stop recording, press the Stop button 9 to finish recording.

Note:

≥If you leave the VCR in the recording pause mode for more than 5 minutes in step 3 or 6, the VCR automatically switches over to the stop mode to protect the video heads.

22

Connecting the VCR to a Decoder

To connect this VCR to a decoder, make the connections shown in the illustration below.

For the connection to the TV, see pages 8 and 10.

For details about the connection, also read the operating instructions of the decoder.

Be sure to keep the VCR, TV and decoder switched off until you have finished all connections.

For your safety, do not connect or handle the equipment with wet hands.

To Connect the VCR to a Decoder

Decoder here refers to the device used to decode scrambled broadcasts (Pay TV).

b

Decoder (not supplied)

 

1

2

21-pin Scart socket

To an AC mains socket

21-pin Scart cable

 

 

(not supplied)

1Connect a 21-pin Scart cable (not supplied) to the AV2 21-pin Scart socket b on the VCR and to the 21-pin Scart socket on the decoder.

2Connect the decoder’s mains lead to an AC mains socket.

3Set “AV2” to “DECODER”. For details, see page 30.

AV Link Function

If the VCR is connected to the TV via a 21-pin Scart cable, you can use AV LINK button B to switch the TV from normal TV reception over to the video playback channel (AV input) (and vice versa). In the VCR mode (when the VCR indication in the VCR display is lit), the TV is switched to the video playback channel (AV input). In the TV mode (when the VCR indication is not lit), the TV is switched to TV reception.

 

VCR

TV

VCR Mode

VCR indication

AV Input

 

is lit.

is selected.

 

 

 

TV Mode

VCR indication

TV reception is

 

is not lit.

selected.

≥When you press the MENU button T to display the menu on the TV screen, the TV is also automatically switched to the VCR mode, however, the VCR indication does not appear in this case.

≥When you start playback on the VCR, the TV is automatically switched to the VCR mode. However, during playback, it is not possible to switch the TV back to the TV mode.

≥If a Pay TV station has been selected on the VCR when you switch to the TV mode, the picture on the TV is scrambled when you select a Pay TV station on the TV. In this case, either switch to the VCR mode or select the AV input on the TV.

Hint:

≥“RGB” means separate Red/Green/Blue colour signals. If you connect a TV equipped with RGB input capability to the AV1 socket a on this VCR, and a decoder equipped with RGB output capability to the AV2 socket b, the TV can receive RGB signal input from the decoder via the VCR.

Page 21 Page 23
Image 22
Page 21 Page 23
Contents NV-SJ260 Series Contents Dear CustomerControls and Components VCRIf the Sliding Cover of the Remote Control Becomes Detached Preparing the Remote ControlInserting Remote Control Batteries VCR OperationDo not Remove Outer Cover RemarksSetting the Remote Control to Operate Your TV TV OperationList of TVs Compatible With the VCR’s Remote Control Manufacturer CodeHints To Set Up this VCR with a TV Already Preset Download FunctionTo Simultaneously Set Up this VCR with a New TV UsePage To Confirm that the TV Stations Have Been Auto Setup FunctionTuned Correctly by the Auto Setup FunctionDisplay Playback To Eject the Video Cassette Using the Remote Controller To Stop Playback Automatically Playback Off Timer FunctionConvenient Automatic Functions To Pause Recording RecordingTo Display the Approximate Remaining Tape Time Linked Timer Recordings with a Digital Receiver To Prevent Accidental Erasure of Recorded ContentsPress the OK button S to conclude the settings Timer RecordingTo Suspend the Timer Recording Standby Mode To Programme with the On Screen Display OSDTo Programme with ShowView Function Press the OK button S to display the programmed contentPress the OK button S again to conclude Settings Press the Numeric buttons 2 to enter the ShowView numberTo Check the Contents of Timer Recording Programmings Other Timer Recordings and Convenient FunctionsSetting the Recording Date/Days To Change a Timer Recording ProgrammingTo Cancel the Programme List Search To Cancel the Programming of a Timer RecordingTo Check the Total Timer Recording Programming Time PreparationSearch Functions To Cancel the Index Search or to Stop PlaybackTo Cancel the Intro-Jet Scan or to Stop Playback OperationAssemble Editing Connecting the VCR to a DecoderEditing To Connect the VCR to a DecoderSatellite receiver not supplied Pin Scart socket To Enter or Change the Name of a TV Station List of TV Reception Channels To Obtain the Best Tuning ConditionTo Enter Newly Available TV Stations To Change the Channel Number of an Already Tuned TV StationTo Preset Pay TV Stations To Change the Type of Video System Colour TV systemTo Restart the Download To Restart the Auto SetupTo Return the VCR to the Shipping Condition To Manually Adjust the Clock Setting the VCR’s ClockTo Activate the Automatic Time Correction Function Video system colour TV system Tape length indicator Other Convenient Functions Various SettingsSettings for the Main Menu Item Display TV station nameSettings for the Main Menu Item Functions DimmedCountry Setting Language SettingTo Set the Remote Control Mode Crystal View Control CVC GlossaryVPS Video Programme System/ PDC Programme Delivery Control Programming ShowView Changes Non MethodMessage Message appears when Link FunctionPin Scart Socket AV1 Scart Socket for Q Link connection√ The VCR Does Not Work Correctly Before Requesting Service√ On Screen Display Messages √ Playback Does Not Work Properly√ The Remote Control Does Not Work Correctly √ Recording Is Not Possible or Does Not Work ProperlyPrecautions Adjusting the Playback PictureIf the Still Picture Scrolls Up or Down V-Lock Adjustment To Return to Auto TrackingCleaning the VCR Avoid sudden changes in temperatureKeep the VCR away from high temperatures Avoid humidity and dustSpecifications
Top Page Image Contents