Panasonic NV-SJ260 Link Function, Pin Scart Socket, Message Message appears when

Page 33

Q Link Function

This function works only if the VCR is connected via a fully- wired 21-pin Scart cable to a TV featuring the Q Link or similar function.

Q Link offers the following functions:

(1)Download from the TV

When you connect the VCR to a TV, the station list data is automatically copied from the TV to the VCR, and the TV stations are assigned to the programme positions on the VCR in the same order as on the TV.

(2)Direct TV Recording

By simply pressing the DIRECT TV REC button 6, you can at once record the same programme that you are watching on the TV.

°(3) TV/VCR Auto Power On

Even if the TV and the VCR are off (standby mode), pressing the Play I, SHOW VIEW L or PROG./CHECK button < automatically turns on both the TV and the VCR.

≥When a cassette with a broken erasure prevention tab is in the VCR, it turns on and starts playback. The TV also turns on.

°(4) VCR Auto Power Off

When you turn the TV off, the VCR is turned off as well. However, this function only works during rewinding, in the stop mode, or when no cassette is inserted.

If the VCR receives the Auto Power Off command while it is rewinding the tape, it turns off after the rewinding has been finished.

This function does not work during the following operations:

Preset Download, Auto Setup, Auto Clock Setting and Manual Tuning.

°(5) On Screen Display Messages

When you are watching a TV programme, the following VCR messages appear on the TV screen to inform you of the VCR’s condition:

Message

Message appears when:

This programme has

A timer recording has just started.

already started

 

 

 

Set VCR to timer

The VCR is not in the timer standby

standby mode

mode 10 minutes before the

 

programmed recording start time of a

 

timer recording (message appears

 

every minute during these

 

10 minutes).

 

 

VCR is in timer

The VCR-ON/OFF 1, Play I,

standby mode

EJECT Z or SEARCH button M was

 

pressed, although the VCR is in the

 

timer standby mode.

 

 

VCR is in timer

The VCR-ON/OFF 1, Stop 9, REC/

recording mode

OTR _, Pause/Slow 7 or SHOW

 

VIEW L was pressed while the VCR

 

is in the timer recording mode.

 

 

≥Depending on the type of TV used, the above messages may not appear correctly.

°The operations marked with asterisk are only available if the VCR is connected to a TV featuring the Q Link or the DATA LOGIC function.

Note:

≥If “Power save” is set to “ON”, the Q Link functions do not work when the VCR is switched off (standby mode).

21-pin Scart Socket

The 21-pin Scart socket transmits both input and output signals for picture and sound. TVs equipped with the same type of socket can be connected here.

This type of socket is also called Peritel, Euro Connector and Euro AV.

13 5 7 9 11 13 15 17 19 21

2 4 6 8 10 12 14 16 18 20

AV1 Scart Socket (for Q Link connection)

1

Audio output

12

No connection

2

Audio input

13

Red ground

3

Audio output

14

Blanking ground

4

Audio ground

15

Red

5

Blue ground

16

Blanking

6

Audio input

17

Video output ground

7

Blue

18

Video input ground

8

Switching voltage

19

Video output

9

Green ground

20

Video input

10

Q Link data

21

Ground

11

Green

 

 

AV2 Scart Socket

 

 

1

Audio output

12

Reserved

2

Audio input

13

Red ground

3

Audio output

14

Blanking ground

4

Audio ground

15

Red

5

Blue ground

16

Blanking

6

Audio input

17

Video output ground

7

Blue

18

Video input ground

8

Switching voltage

19

Video output

9

Green ground

20

Video input

10

Control signal

21

Ground

11

Green

 

 

The Red, Green and Blue (RGB) video signals are looped through only from an external source unit, for example from a connected a pay-TV decoder, i.e. they are not from tape playback.

Helpful Hints

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents NV-SJ260 Series Dear Customer ContentsVCR Controls and ComponentsInserting Remote Control Batteries Preparing the Remote ControlIf the Sliding Cover of the Remote Control Becomes Detached VCR OperationRemarks Do not Remove Outer CoverTV Operation Setting the Remote Control to Operate Your TVManufacturer Code List of TVs Compatible With the VCR’s Remote ControlHints To Simultaneously Set Up this VCR with a New TV Preset Download FunctionTo Set Up this VCR with a TV Already UsePage Tuned Correctly by the Auto Setup Auto Setup FunctionTo Confirm that the TV Stations Have Been FunctionDisplay Playback To Stop Playback Automatically Playback Off Timer Function To Eject the Video Cassette Using the Remote ControllerConvenient Automatic Functions Recording To Pause RecordingTo Display the Approximate Remaining Tape Time To Prevent Accidental Erasure of Recorded Contents Linked Timer Recordings with a Digital ReceiverTo Suspend the Timer Recording Standby Mode Timer RecordingPress the OK button S to conclude the settings To Programme with the On Screen Display OSDPress the OK button S again to conclude Settings Press the OK button S to display the programmed contentTo Programme with ShowView Function Press the Numeric buttons 2 to enter the ShowView numberSetting the Recording Date/Days Other Timer Recordings and Convenient FunctionsTo Check the Contents of Timer Recording Programmings To Change a Timer Recording ProgrammingTo Check the Total Timer Recording Programming Time To Cancel the Programming of a Timer RecordingTo Cancel the Programme List Search PreparationTo Cancel the Intro-Jet Scan or to Stop Playback To Cancel the Index Search or to Stop PlaybackSearch Functions OperationEditing Connecting the VCR to a DecoderAssemble Editing To Connect the VCR to a DecoderSatellite receiver not supplied Pin Scart socket To Enter or Change the Name of a TV Station To Enter Newly Available TV Stations To Obtain the Best Tuning ConditionList of TV Reception Channels To Change the Channel Number of an Already Tuned TV StationTo Change the Type of Video System Colour TV system To Preset Pay TV StationsTo Restart the Auto Setup To Restart the DownloadTo Return the VCR to the Shipping Condition Setting the VCR’s Clock To Manually Adjust the ClockTo Activate the Automatic Time Correction Function Settings for the Main Menu Item Display Other Convenient Functions Various SettingsVideo system colour TV system Tape length indicator TV station nameDimmed Settings for the Main Menu Item FunctionsLanguage Setting Country SettingTo Set the Remote Control Mode VPS Video Programme System/ PDC Programme Delivery Control GlossaryCrystal View Control CVC Programming ShowView Changes Non MethodPin Scart Socket Link FunctionMessage Message appears when AV1 Scart Socket for Q Link connection√ On Screen Display Messages Before Requesting Service√ The VCR Does Not Work Correctly √ Playback Does Not Work Properly√ Recording Is Not Possible or Does Not Work Properly √ The Remote Control Does Not Work CorrectlyIf the Still Picture Scrolls Up or Down V-Lock Adjustment Adjusting the Playback PicturePrecautions To Return to Auto TrackingKeep the VCR away from high temperatures Avoid sudden changes in temperatureCleaning the VCR Avoid humidity and dustSpecifications
Top Page Image Contents