Panasonic AJ-D960EG manual Setup menus, Setting and releasing the lock mode

Page 56

Setup menus

Lock mode can be set to protect the settings in the system files and user files (USER2 – USER5). Settings can no longer be changed when this mode is set.

To set and release the lock mode for the system files and user files use setup item No. 30 (MENU LOCK) and setup menu item No. A03 (MENU LOCK), respectively.

Setting and releasing the lock mode.

1

2

Press the MENU button.

While holding down the STAND BY button, press the REW or FF button, and select the file for which the lock mode is to be set or released.

3

4

Turn the search dial and move the cursor ( ) on the menu screen to setup item No. 30 (MENU LOCK) or setup menu item No. A03 (MENU LOCK) for the system or user file.

While holding down the search button, turn the search dial and select lock mode setting or release.

To set the lock: Select the 0001 (ON) setting.

To release the lock: Select the 0000 (OFF) setting.

When the lock has been set, “LOCKED” flashes on the menu screen. In addition, the counter display stops flashing and lights.


SETUP-MENU			LOCKED
<USER2>			No.800	– 0005
000	P–ROLL TIME				5s
001	LOCAL ENA				ST&EJ
002	TAPE TIMER				±12h
003	REMAIN SEL				OFF
004	SETUP	NUMBER			OFF
005	METER	SELECT			CUE
006	SYNCHRONIZE				OFF
007	SUPER				ON
008	DISPLAY SEL				T&STA

5

Press the SET button. The setting is now stored in the memory.

<Notes>

•The lock mode cannot be set for the USER1 file settings.

•Even if the RESET button is pressed, the files which has been set to the lock mode cannot be reset to the factory settings.

56 (E)

Image 56

Contents Operating Instructions Not to be used in the U.K How to replace the fuseFor U.K. only Operating precaution Damage both to the recorder and to the tapeContents General and Features FeaturesMenu-driven setup Dial shuttleTime codes Multifunctional interfaceFront Panel Top Section Controls and their functionsFront panel Input Select switches VideoAudio Input Select displayFront Panel Centre Section 9TC/CTL switch @0TC/UB switch@1INT/EXT switch @2TAPE/EE switch In the stop mode@3REMOTE/LOCAL switch @7SHTL/SLOW switch@4REMOTE lamp @5Search button#0PREROLL button #1AUTO Edit button#2PREVIEW/REVIEW buttons #3IN a IN/SET/OUT a OUT buttons$6Headphones jack #8Time code buttons#9Warning lamp $0Cassette insertion display lamp$9METER FULL/FINE selector switch $7Volume control$8MONITOR Select switches Front Panel Bottom Section 7REC Inhibit switch 8TV System selector switch9MENU button 0SET buttonConnector area 0y t ui oAC in connector Signal GND terminalTime Code in connector Time Code OUT connector5ANALOG Component Video OUT connector option 6ANALOG Composite Video OUT connectors7DIGITAL Audio IN/OUT connector 8SERIAL Digital Component AUDIO/VIDEO IN/OUT connectorConnections when one unit is used ConnectionsConnections when 2 units are used deck to deck Recorder DeviceAudiomonitor Signals AV monitor Reference Audio output signals Reference signalVideo monitor Signals Audio monitor Reference signalWFM VSC Tapes TypeSwitching on the power/inserting the cassette Stand by PlayerSTOP/STAND by mode Still Timer SettingSelecting video/audio input signals Adjusting the video levelAdjusting the audio level RecordingPlayback Jog/shuttle Jog modeShuttle mode Manual editing Preroll Automatic editing Deck to Deck Switch settings and adjustments When the unit is used as the recorderWhen the unit is used as the player Automatic editingSelect the editing mode Negative duration function Entering the edit pointsMatch frame processing function Checking the edit points Calculating the durationModifying the edit points Resetting both the edit in and OUT points2Resetting either the edit in or OUT point Preview Executing automatic editing PostrollRetry function Auto tag editingReview Audio split editing Entering the edit pointsDeleting the edit points Modifying the edit pointsDisplaying the audio split edit points Cueing up the tape to the edit pointsDuration display OperationsOperating procedure Voice-over facility internal00000000 m Stop For operation with an editing controller AG-A850 VTRConnections Example To record cross-faded audio signals onto CH2Audio cross channel editing internal 47 E I L L Multi cueDescription of display Search point operations OperationsSearch point or entry point operations 1 2 2 0 Entry point operationsSearch point and entry display operations M O R Entering cue pointsOperations on the selected page page MODE=MANU When entering a cue point as a number Individual entered point resettingClearing entered points Search operationsVideo output encoder output signal adjustments Chroma level and chroma phaseBlack level Video levelSETUP-MENU Init SET YESPLAY/NOSTOP Setup default settingsChanging the settings Setup setting menus Changing the fileSetup menus Setting and releasing the lock modeLoading a user file USER1Automatic loading of user file when the power is turned on Saving a user fileSystem Setting DescriptionSystem menu Setting Item adjusted System Setting DescriptionVideo output signal adjustments User menu BasicBasic Setting Description Dvcpro DvcamMoni ManuOperation Operation Memory stop functionFRZ Mode StboffSOF&EJ INHRota Mode EjectMODE1 MODE2Interface Interface Local 25PMaster IN/OUTEdit Edit Setting Description AUD MEM AmuxAmuvo IntxPostroll JOG FWDJOG REV Tape Protect Time Code Vaux video auxiliary data area Time CodeSBC sub code data area Video Video Setting Description Audio Audio Setting Description User menu Audio Setting Description Direct Moni SELON1 MON AutoBlank ADD LineREC LINE1 REC LINE2Blank Setting Description Y4BPFREC LINE3 REC LINE40000 10L 0014 273L0012 22L 0013 263L 0014 273L 0016 275L 0025 284L 0026 525L 0003 13LTeletext MojiNabts DETBlank Line 88 E Menu Time code/user bit Time codeUser bit TCR 00 07 04 Frames Hours Seconds MinutesRecording internal/external time codes Setting the internal time codeSetting the external time code TC switch → EXT Reproducing the time code/user bit Operation mode Superimpose screenCharacters displayed Display positionStart Video output signals and servo reference signalExternal synchronization of video output signals Servo reference signal Audio V Fade Function Monitor output channel Audio recording channel and monitor output selectionAudio recording channel Printed circuit board Printed Abbr Factory Circuit Full name FunctionBoard NameRack mounting Condensationy Video head cleaningInstalling the mechanism dust protector Displaying the Diag menu Error messagesDiag menu Priority Display Description Displaying the Hours Meter informationItem No Description Priority Monitor display Description VTR operation Table of Auto OFF Error messages Power OFF→ONCounter display Monitor display Description VTR operation Restart conditionPower OFF →ON Reel DIR UnmatchHardware specifications External interface specificationsRS-232C interface IntroductionSoftware specifications ProtocolError code table When the communication has terminated abnormally NackReturn format VTR → controller PC STX OPL ETX ACK STX OPL ETXCommand table Commands relating to operation control NotesReturn completion Send command Supplementary notes OperationSTX OSR ETX ReverseStandby STX OBF ETX OFF Standby STX OBN ETXCommands relating to inquiries Notes Microsoft QuickBASIC sample programme CLSHow to use the SDTI/SDI common input signals Using the signals as the SDI input signalsUsing the signals as the Sdti input signals Sdti interface boardHow to use the SDTI/SDI common output signals How to use the 2⋅ speed transmission modeUsing the signals as the SDI output signals Using the signals as the Sdti output signalsPrecautions to observe when using the Sdti signals Reference signal generator SourceConnector signals Pin No. SignalSignal Pin No SignalRS-232C Remote 25-pin D-SUB crossover cable supported Pin No Abbreviation Circuit DescriptionSpecifications AC 220 240 V, 50 60 Hz 280 WVideo Output Connector Video Signal AdjustmentAudio Input Connector Audio Output ConnectorPanasonic Broadcast Europe Panasonic Broadcast Europe GmbH