*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
Audio Output (DVD only)
Select the digital output to be output from the optical digital audio output connector of DECK.
1Press ACTION
to display DVD MAIN MENU.
2
Press 
to select
“AUDIO OUTPUT,”
and
press SET
to display screen.
3
Press 
to select an item,
and
press SET repeatedly for output. (See below.)
■“LPCM (DVD)” selections
OFF: Linear PCM of less than 48 kHz/16 bit is output. When playing DVDs recorded in linear PCM of over 48 kHz/20 bit, no digital audio is output. (Factory preset)
PCM: When playing DVDs recorded in linear PCM of 48 kHz/20 bit/24 bit or more, digital audio converted to 48 kHz/16 bit is output.
(Digital output of PCM audio is restricted to 48 kHz/16 bit or below for copyright protection.)
■“Dolby Digital” selections
Bitstream: Dolby Digital bitstream (1 ch - 5.1 ch) is output. (Factory preset)
PCM: When you have connected an amplifier that doesn’t have a
■“dts” selections
Bitstream: DTS bitstream is output. (Factory preset)
PCM: When you have connected an amplifier that doesn’t have a
Ready Checklist
DECK is in DVD mode, press DVD.
Type of amplifier |
| Recommended setting | |||||||
LPCM | Dolby |
|
|
| |||||
to be connected |
| D T S | |||||||
| ( DV D ) | Digital |
|
|
| ||||
No amplifier is |
|
|
|
|
|
|
|
|
|
connected |
|
|
|
|
|
|
|
|
|
AV amplifier (with |
|
|
|
|
|
|
|
|
|
digital audio input |
|
|
|
|
|
|
|
|
|
connector) without | P C M | PCM* 1 | PCM*1 | ||||||
Dolby Digital/DTS |
|
|
|
|
|
|
|
|
|
decoder |
|
|
|
|
|
|
|
|
|
AV amplifier |
|
|
|
|
|
|
|
|
|
including Dolby | P C M | Bitstream |
| P C M | |||||
Digital decoder |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AV amplifier |
|
|
|
|
|
|
|
|
|
including Dolby | P C M | Bitstream | *2 | ||||||
Digital/DTS | Bitstream | ||||||||
decoder |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
•Make settings according to amplifier connected to optical audio output as shown in above table.
*1 When connecting an amplifier (with an optical digital input connector) which does not contain the Dolby Digital or DTS decoder, be sure to select “PCM”.
If “Bitstream” is selected, starting DVD play may cause such a high level of noise as to be harmful to your ears and damage the speakers.
*2 When a dts decoder is connected, please select “Bitstream” in “dts.”
If “PCM” is selected, there will be stereo sound.
When a Dolby Digital decoder is connected, please select “Bitstream” in “Dolby Digital.”
If “PCM” is selected, there will be stereo sound.
DVD Operation
■“DRC (Dynamic Range Compression)”
selections
OFF: Normal audio range is selected. (Factory preset)
ON: For dynamic sound even at low volume, this is useful for
4Press ACTION to redisplay DVD MAIN MENU and go to step 2 to setup another item.
Or, press ACTION twice to exit.
53