JVC HR-S7800U manual Cable Box Control Setting, Installing Controller, Situate Controller

Page 15

Controller (suggested locations)

Cable box

EN 15

Cable Box

Control

Setting

Suggested location

Place the cable box on top of the VCR. Attach the VCR’s Controller to the top of the VCR with the Controller’s transmitter pointed towards the cable box’s remote sensor.

ATTENTION:

The Controller can also control a DBS receiver. If both a cable box and a DBS receiver are used, position the Controller so its signal reaches the remote sensors on both the cable box and DBS receiver.

Your VCR

Cable box

To	To
RF output	audio/video
Controller	output
Transmitter
	or
To	To
ANTENNA	AUDIO/
IN	VIDEO IN

Your VCR

CABLE

BOX

The following procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the VCR to automatically switch the cable box channel during timer recording. The Controller is effective for recording broadcasts that have been programmed using VCR Plus+ ( pg. 30) or Express timer programing ( pg. 34).

Installing Controller

1 Situate Controller

Place the Controller so that its transmitter is facing the cable box’s remote sensor.

Make sure the path between the Controller and the cable box’s remote sensor is not blocked.

2 Attach Controller

Fix securely using the adhesive strip attached on the back of the Controller.

3 Connect cable box to VCR

If your cable box does not have audio/video output connectors

Connect the RF output terminal on the cable box to the ANTENNA IN terminal on the rear of your VCR.

If your cable box has audio/video output connectors

Connect an audio/video cable between the AUDIO/VIDEO IN connectors on the rear of the VCR and the audio/video output connectors on the cable box.

NOTE:

When connecting your cable box, refer to its instruction manual.

4 Connect Controller to VCR Connect the Controller to the CABLE BOX Controller connector on the rear panel.

How to control the cable box

This VCR has two separate methods to control your cable box.

The VCR’s wireless Remote can control your cable box. This eliminates the need for a separate cable box’s Remote.

The VCR’s Controller can also control your cable box. This allows the VCR to change your cable box’s channel number during timer recording.

Each method must be set up separately. To set up the VCR’s Remote, refer to page 51. To set up the Controller, go to page 16.

Image 15

Contents HR-S7800U Telephone Number Dear CustomerGrounding or Polarization Power SourcesPower Lines Power Cord ProtectionReplacement Parts AccessoriesDamage Requiring Service CleaningContents Back of VCR Basic ConnectionsAntenna Video OUTCheck contents Final preparation for use Situate VCRConnect VCR to TV Clock and tuner channels will be set automatically Plug & Play SettingPerform Plug & Play setup What to do if Plug & Play setting failedPress Menu Language SettingSelect language Return to normal screen10 EN Clock SettingAccess Main Menu screen Access clock set screenSelect host channel Setting clock semiautomaticallySelect D.S.T. mode Set Auto Clock to on To make corrections any time during the process Setting clock manually 12 EN Manual Clock SetPerform Auto Channel Set Tuner SettingSetting channels automatically Access Tuner Set screenAdd or skip desired channels Setting channels manuallyAccess Manual Channel Set screen 14 ENAttach Controller Cable Box Control SettingInstalling Controller Situate Controller16 EN Setting cable box output channel & brandAccessPress OKCable. Box Brand Set screen Enter cable box brandIf the cable box’s channel does not change to Antenna Video How to control the DBS receiver18 EN Connect DBS receiver to VCRSelect DBS receiver output channel Setting DBS receiver output channel & brandAccess DBS Receiver Set screen Turn on DBS receiverShuttle Plus %Þ Access DBS Receiver Brand Set screen20 EN Enter DBS Receiver’s brandBasic Playback Load a cassetteStart playback Checking tape position Basic Playback Features22 EN Changing display informationLocating beginning Adjusting tracking conditionSelecting monitor sound Automatic operations afterRecordings Instant Review Locating beginning of timerAdjusting picture condition 24 ENStart recording Basic RecordingSelect recording channel Set tape speedWatching one program while recording another Basic Recording Features26 EN Specifying recording lengthExit on-screen display Select S-VHS ET modeShowing on-screen display Display VCR status on TV screenRapidly Picture Search High-Speed Picture Search Special Effect Playback28 EN Locating particular scenePause during playback Viewing still pictureSkipping unwanted portions Viewing slow motion picturePress the appropriate VCR Plus+ Timer ProgramingDaily M-F Power Weekly 30 ENPress SP/EP Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Input receiving channel numberChanging VCR Plus+ Setting 32 ENVCR Plus+ guide channel matching Input guide channel number Access Guide Channel Set screenSet program stop time Express Timer ProgramingDaily Power 34 ENDBS To timer-record daily Monday-Friday or weekly serialsOFF Catv36 EN Checking program settingsConfirm overlapping programs Select program to modifyOverlapping programs blink on the screen 38 EN Useful Function SettingsAccess Function Set screen Change settingWhen this function is set to OFF When this function is set to onEntire program while timer-recording in SP mode 40 ENFor Example Remote Pause terminal. pg Mode is used for recording on S-VHS tapesVia their AV Compulink connectors becomes possible VHS picture qualityThis VCR Purpose before you start the editing procedure pg toTo cancel the editing function, select REC-PAUSE 42 ENChild Lock Power TimerVarious connection for editing tapes Edit From Camcorder44 EN ConnectionSet Picture Control to Edit Select input mode on this VCRMake connections Select video input terminalLoad cassettes Select edit modeEdit To Or From Another 46 ENStart audio dubbing Select input modeAudio Dubbing Locate start pointAV Dubbing Source tape Edited tape 48 ENAnother VCR for playback Insert Editing Source tape Edited tapeLocate end point Activate editing modePrepare tapes Select editing function you wantSet TV brand code TV Brand Setting50 EN Turn on the TVOperate cable box Cable Box Brand SettingTurn on the cable box Enter cable box brand codeEnter DBS receiver brand code DBS Receiver Brand Setting52 EN Turn on the DBS receiverPlug in VCR Changing Remote Control CodeSet remote control code for Remote Unplug VCR54 EN TroubleshootingTimer Recording 56 EN Other ProblemsWhat happens if the tape reaches its end during recording? Can the VCR indefinitely remain in still mode?List of terms 58 ENFront display panel Front panel60 EN Rear panelOn-screen display Remote How to use the RemoteFull-Size VHS 30 ST-30 62 ENUsable cassettes Operating position Horizontal onlyHOW to Locate Your JVC Service Center 64 EN Limited WarrantyMemo 66 EN Page HR-S7800U