JVC HR-S7800U Prepare tapes, Select editing function you want, Locate end point, Start editing

Page 49

EN 49

1 Make connections

Connect an audio/video cable between the VCR’s audio/video input connectors and the other component’s audio/video output connectors.

2 Prepare tapes

Load the source tape on the other VCR, and the tape to be edited on this VCR.

3Select input mode

Select “F-1” — when connecting the other component to the audio/video input connectors on the front panel.

Select “L-1” — when connecting the other component to the audio/video input connectors on the rear panel.

On the front panel:

Press CH5°.

On the Remote:

Press the Number key “0 (AUX)” or CH +/–.

4 Select editing function you want

Set “EDIT FUNCTION” to either “INSERT” or “AV DUB” whichever you want to use by following the procedure described on pages 38 and 42.

Make sure to set “EDIT FUNCTION” to “REC- PAUSE” after you finish editing tapes. This cancels the editing function.

5 Select video input terminal

Follow the procedure described on pages 38 and 42.

When using S VIDEO terminal, set “FRONT AUX INPUT” (or “REAR AUX INPUT” if you use the connectors on the rear) to “S-VIDEO”.

When using VIDEO terminal, set “FRONT AUX INPUT” (or “REAR AUX INPUT”) to “VIDEO”.

6 Select edit mode

Set the edit mode to “ON” for the VCRs if such a mode is equipped.

On this VCR, set “PICTURE CONTROL” to “EDIT” by following the procedure described on pages 38 and 39.

7 Locate end point

1 Press PLAY ( 3 ) to start playback.

2 Press PAUSE ( 8 ) when you find the end of the scene for which you want to edit.

3 Press C. RESET so that the counter reading becomes “0:00:00”.

NOTE:

8Locate start point

Use REW ( ) or SHUTTLE ring to reverse the

tape. (See “Special Effect Playback”: pg. 28.) When you find the beginning of the scene you want to edit, press PAUSE 8.

9Activate editing mode

Press REC ( ƒ ) on the front panel.

Make sure that the recording format (VHS, S- VHS or S-VHS ET) on the VCR is the same as that of the original recording on the tape.

During Insert Editing pause mode (, and light up on the front display panel.)

During AV Dubbing pause mode ( and blink, and lights up on the front display panel.)

0Start editing

Press PLAY ( 3 ) on this VCR, and start playback on the other component at the same time.

During Insert Editing mode ( and light up on the front display panel.)

During AV Dubbing mode ( and blink on the front display panel.)

When the counter reading becomes “0:00:00”, editing automatically stops, and the VCR starts normal playback.

To stop editing any time during recording

Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 ) on the front panel.

NOTES:

Be sure to select “AUTO” for “PICTURE CONTROL” (or “NORM” when “VIDEO CALIBRATION” is set to “OFF”) after you finish editing the tapes ( pg. 38 and 39).

Editing cannot be performed on a tape with its record safety tab removed.

The recording speed (SP/EP) is determined by the previous recording to be replaced. If the recording speed changes on the tape to be edited while editing the tape, the inserted picture will be distorted where the recording speed changes. When you edit a tape, a small portion of the recording preceding to the editing start point will be erased from the edited tape.

You can also use FF ( ) or SHUTTLE ring to locate the end point (See “Special Effect Playback”: pg. 28)

.

Page 48 Page 50
Image 49
Page 48 Page 50
Contents HR-S7800U Telephone Number Dear CustomerPower Lines Power SourcesPower Cord Protection Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsContents Antenna Basic ConnectionsVideo OUT Back of VCRSituate VCR Check contents Final preparation for useConnect VCR to TV Perform Plug & Play setup Plug & Play SettingWhat to do if Plug & Play setting failed Clock and tuner channels will be set automaticallySelect language Language SettingReturn to normal screen Press MenuAccess Main Menu screen Clock SettingAccess clock set screen 10 ENSelect D.S.T. mode Setting clock semiautomaticallySet Auto Clock to on Select host channel12 EN Setting clock manuallyManual Clock Set To make corrections any time during the processSetting channels automatically Tuner SettingAccess Tuner Set screen Perform Auto Channel SetAccess Manual Channel Set screen Setting channels manually14 EN Add or skip desired channelsInstalling Controller Cable Box Control SettingSituate Controller Attach Controller16 EN Setting cable box output channel & brandEnter cable box brand AccessPress OKCable. Box Brand Set screenIf the cable box’s channel does not change to 18 EN How to control the DBS receiverConnect DBS receiver to VCR Antenna VideoAccess DBS Receiver Set screen Setting DBS receiver output channel & brandTurn on DBS receiver Select DBS receiver output channel20 EN Access DBS Receiver Brand Set screenEnter DBS Receiver’s brand Shuttle Plus %ÞLoad a cassette Basic PlaybackStart playback 22 EN Basic Playback FeaturesChanging display information Checking tape positionSelecting monitor sound Adjusting tracking conditionAutomatic operations after Locating beginningAdjusting picture condition Locating beginning of timer24 EN Recordings Instant ReviewSelect recording channel Basic RecordingSet tape speed Start recording26 EN Basic Recording FeaturesSpecifying recording length Watching one program while recording anotherShowing on-screen display Select S-VHS ET modeDisplay VCR status on TV screen Exit on-screen display28 EN Special Effect PlaybackLocating particular scene Rapidly Picture Search High-Speed Picture SearchSkipping unwanted portions Viewing still pictureViewing slow motion picture Pause during playbackDaily M-F Power Weekly VCR Plus+ Timer Programing30 EN Press the appropriateTo use the VCR while it is in timer recording standby mode Engage timer recording standby modeInput receiving channel number Press SP/EP32 EN Changing VCR Plus+ SettingVCR Plus+ guide channel matching Input guide channel number Access Guide Channel Set screenDaily Power Express Timer Programing34 EN Set program stop timeOFF To timer-record daily Monday-Friday or weekly serialsCatv DBS36 EN Checking program settingsSelect program to modify Confirm overlapping programsOverlapping programs blink on the screen Access Function Set screen Useful Function SettingsChange setting 38 ENWhen this function is set to OFF When this function is set to on40 EN Entire program while timer-recording in SP modeFor Example Via their AV Compulink connectors becomes possible Mode is used for recording on S-VHS tapesVHS picture quality Remote Pause terminal. pgTo cancel the editing function, select REC-PAUSE Purpose before you start the editing procedure pg to42 EN This VCRChild Lock Power Timer44 EN Edit From CamcorderConnection Various connection for editing tapesMake connections Select input mode on this VCRSelect video input terminal Set Picture Control to Edit Edit To Or From Another Select edit mode 46 EN Load cassettesAudio Dubbing Select input modeLocate start point Start audio dubbingAnother VCR for playback 48 ENInsert Editing Source tape Edited tape AV Dubbing Source tape Edited tapePrepare tapes Activate editing modeSelect editing function you want Locate end point50 EN TV Brand SettingTurn on the TV Set TV brand codeTurn on the cable box Cable Box Brand SettingEnter cable box brand code Operate cable box52 EN DBS Receiver Brand SettingTurn on the DBS receiver Enter DBS receiver brand codeSet remote control code for Remote Changing Remote Control CodeUnplug VCR Plug in VCR54 EN TroubleshootingTimer Recording 56 EN Other ProblemsWhat happens if the tape reaches its end during recording? Can the VCR indefinitely remain in still mode?List of terms 58 ENFront display panel Front panelRear panel 60 ENOn-screen display Remote How to use the RemoteUsable cassettes 62 ENOperating position Horizontal only Full-Size VHS 30 ST-30HOW to Locate Your JVC Service Center 64 EN Limited WarrantyMemo 66 EN Page HR-S7800U
Top Page Image Contents