JVC HR-S7800U manual Basic Playback, Load a cassette, Start playback

Page 21

BASIC PLAYBACK AND RECORDING

EN 21

Basic

Playback

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

2 SHUTTLE

POWERring

				REW
POWER				MENU
					PLAY
	DIGITAL TBC/NR
S-VIDEO	VIDEO (MONO)L—AUDIO—R
	S-VHS ET	SP EP	CH	REC	STOP/EJECT PAUSE
	S-VHS ET	VCR	CH	REC	STOP/EJECT PAUSE
				OK
		1		STOP/EJECT
		1		( 7 / 0 )

POWER

1 2 3

2

4 5 6

7 8 9

0 4

2

1

REW ( 1 ) FF ( ` )

STOP ( 7 )

This VCR can check the tape condition during playback (and recording), and realizes the best possible pictures.

1 Load a cassette

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR.

Do not apply too much pressure when inserting.

The VCR turns on automatically.

The counter is automatically reset to “0:00:00”. If the cassette’s record safety tab has been removed, playback begins automatically.

2Start playback

Press PLAY ( 3 ).

Tape speed (SP or EP) is automatically detected. The S-VHS indicator lights up when you play back a tape recorded in S-VHS mode or in S- VHS ET mode ( pg. 27)

If “VIDEO CALIBRATION” is set to “ON” (default setting: pg. 39), “VIDEO CALIBRATION” appears on the screen, and this VCR checks the tape condition during automatic tracking.

To stop playback

Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 ) on the front panel.

To rewind the tape (when it is not running)

Press REW ( 1 ) (or turn the SHUTTLE ring on the front panel to the left).

To fast-forward the tape (when it is not running)

Press FF ( ` ) (or turn the SHUTTLE ring on the front panel to the right).

To eject the tape

Press STOP/EJECT ( 7 / 0 ) on the front panel when the tape is not running.

You can also eject the cassette with the VCR turned off.

To turn off the VCR

Press POWER.

Clean the video heads using a dry cleaning cassette — TCL-2UX — when:

•Rough, poor picture appears while a tape is played back.

•The picture is unclear or no picture appears.

•“USE CLEANING CASSETTE” appears on the screen (only with “SUPERIMPOSE” set to “ON”: pg. 38, 39.)

Image 21

Contents HR-S7800U Telephone Number Dear CustomerPower Lines Power SourcesPower Cord Protection Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsContents Antenna Basic ConnectionsVideo OUT Back of VCRCheck contents Final preparation for use Situate VCRConnect VCR to TV Perform Plug & Play setup Plug & Play SettingWhat to do if Plug & Play setting failed Clock and tuner channels will be set automaticallySelect language Language SettingReturn to normal screen Press MenuAccess Main Menu screen Clock SettingAccess clock set screen 10 ENSelect D.S.T. mode Setting clock semiautomaticallySet Auto Clock to on Select host channel12 EN Setting clock manuallyManual Clock Set To make corrections any time during the processSetting channels automatically Tuner SettingAccess Tuner Set screen Perform Auto Channel SetAccess Manual Channel Set screen Setting channels manually14 EN Add or skip desired channelsInstalling Controller Cable Box Control SettingSituate Controller Attach Controller16 EN Setting cable box output channel & brandAccessPress OKCable. Box Brand Set screen Enter cable box brandIf the cable box’s channel does not change to 18 EN How to control the DBS receiver Connect DBS receiver to VCR Antenna VideoAccess DBS Receiver Set screen Setting DBS receiver output channel & brandTurn on DBS receiver Select DBS receiver output channel20 EN Access DBS Receiver Brand Set screenEnter DBS Receiver’s brand Shuttle Plus %ÞBasic Playback Load a cassetteStart playback 22 EN Basic Playback FeaturesChanging display information Checking tape positionSelecting monitor sound Adjusting tracking conditionAutomatic operations after Locating beginningAdjusting picture condition Locating beginning of timer24 EN Recordings Instant ReviewSelect recording channel Basic RecordingSet tape speed Start recording26 EN Basic Recording FeaturesSpecifying recording length Watching one program while recording anotherShowing on-screen display Select S-VHS ET modeDisplay VCR status on TV screen Exit on-screen display28 EN Special Effect PlaybackLocating particular scene Rapidly Picture Search High-Speed Picture SearchSkipping unwanted portions Viewing still pictureViewing slow motion picture Pause during playbackDaily M-F Power Weekly VCR Plus+ Timer Programing30 EN Press the appropriateTo use the VCR while it is in timer recording standby mode Engage timer recording standby modeInput receiving channel number Press SP/EPChanging VCR Plus+ Setting 32 ENVCR Plus+ guide channel matching Input guide channel number Access Guide Channel Set screenDaily Power Express Timer Programing34 EN Set program stop timeOFF To timer-record daily Monday-Friday or weekly serialsCatv DBS36 EN Checking program settingsConfirm overlapping programs Select program to modifyOverlapping programs blink on the screen Access Function Set screen Useful Function SettingsChange setting 38 ENWhen this function is set to OFF When this function is set to onEntire program while timer-recording in SP mode 40 ENFor Example Via their AV Compulink connectors becomes possible Mode is used for recording on S-VHS tapesVHS picture quality Remote Pause terminal. pgTo cancel the editing function, select REC-PAUSE Purpose before you start the editing procedure pg to42 EN This VCRChild Lock Power Timer44 EN Edit From CamcorderConnection Various connection for editing tapesMake connections Select input mode on this VCRSelect video input terminal Set Picture Control to EditEdit To Or From Another Select edit mode46 EN Load cassettesAudio Dubbing Select input modeLocate start point Start audio dubbingAnother VCR for playback 48 ENInsert Editing Source tape Edited tape AV Dubbing Source tape Edited tapePrepare tapes Activate editing modeSelect editing function you want Locate end point50 EN TV Brand SettingTurn on the TV Set TV brand codeTurn on the cable box Cable Box Brand SettingEnter cable box brand code Operate cable box52 EN DBS Receiver Brand SettingTurn on the DBS receiver Enter DBS receiver brand codeSet remote control code for Remote Changing Remote Control CodeUnplug VCR Plug in VCR54 EN TroubleshootingTimer Recording 56 EN Other ProblemsWhat happens if the tape reaches its end during recording? Can the VCR indefinitely remain in still mode?List of terms 58 ENFront display panel Front panel60 EN Rear panelOn-screen display Remote How to use the RemoteUsable cassettes 62 ENOperating position Horizontal only Full-Size VHS 30 ST-30HOW to Locate Your JVC Service Center 64 EN Limited WarrantyMemo 66 EN Page HR-S7800U