JVC HR-S7800U manual Basic Playback Features, 22 EN, Changing display information

Page 22

22 EN

BASIC PLAYBACK AND RECORDING (cont.)

Basic

Playback

Features

C

REW

FF

POWER

MENU

PLAY

	DIGITAL TBC/NR
S-VIDEO	VIDEO (MONO)L—AUDIO—R
	S-VHS ET	SP EP	CH	REC STOP/EJECT PAUSE
		VCR		OK
		D		STOP/EJECT
		D		( 7 / 0 )

				F –b
	E			A
	E	1	2	3
		1	2	3
				2

A Changing display information

Press DISPLAY during playback.

Each time you press the button, the front display panel shows the time counter, tape remaining time and the clock time in sequence.

Time Counter			Tape Remaining Time
Time Counter			Tape Remaining Time

Clock Time

To display the VCR status including the time counter and the clock time on the TV screen, see “Showing on- screen display” ( pg. 27).

“COUNT” appears on the screen when the time counter is shown. “REMAIN” appears on the screen when the tape remaining time is shown.

The approximate tape remaining time appears and the “” indicator lights on the front display panel.

The tape remaining time is calculated based on the tape speed (SP or EP) being used. The indicated remaining time is only an estimate.

To reset the time counter, press C. RESET on the Remote. The counter reading becomes “0:00:00”. It is also reset when a tape is inserted.

B Checking tape position

The tape position indicator

appears on screen in the

4 5

7 8

C. RESET

0

6

9

F –C

D –2

following cases:
When you change the VCR
operation mode from the	B
stop mode to fast forward or
rewind mode.
When you perform an Index

Search ( pg. 23) or Instant Review (

++ + E

COUNT 0:33:27

pg. 24).

1

F –a, b, c

C F –a

The position of “ ” in relation to “B” (Beginning) or “E” (End) shows you where you are on the tape.

NOTES:

STOP ( 7 )

G

“SUPERIMPOSE” must be set to “ON”, or the indicator will not appear ( pg. 38, 39).

It may take a few seconds for the tape position indicator to be displayed.

C Playing back tape repeatedly

— Repeat Play

You can play back a tape repeatedly (100 times).

While playing back a tape, press and hold PLAY ( 3 ) for more than 5 seconds.

The play indicator ( # ) on the front display panel starts flashing slowly, and a tape will be played back 100 times.

To stop playback, press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 ) on the front panel.

Image 22

Contents HR-S7800U Dear Customer Telephone NumberPower Cord Protection Power SourcesPower Lines Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Video OUT Basic ConnectionsAntenna Back of VCRSituate VCR Check contents Final preparation for useConnect VCR to TV What to do if Plug & Play setting failed Plug & Play SettingPerform Plug & Play setup Clock and tuner channels will be set automaticallyReturn to normal screen Language SettingSelect language Press MenuAccess clock set screen Clock SettingAccess Main Menu screen 10 ENSet Auto Clock to on Setting clock semiautomaticallySelect D.S.T. mode Select host channelManual Clock Set Setting clock manually12 EN To make corrections any time during the processAccess Tuner Set screen Tuner SettingSetting channels automatically Perform Auto Channel Set14 EN Setting channels manuallyAccess Manual Channel Set screen Add or skip desired channelsSituate Controller Cable Box Control SettingInstalling Controller Attach ControllerSetting cable box output channel & brand 16 ENEnter cable box brand AccessPress OKCable. Box Brand Set screenIf the cable box’s channel does not change to Connect DBS receiver to VCR How to control the DBS receiver18 EN Antenna Video Turn on DBS receiver Setting DBS receiver output channel & brand Access DBS Receiver Set screen Select DBS receiver output channelEnter DBS Receiver’s brand Access DBS Receiver Brand Set screen20 EN Shuttle Plus %ÞLoad a cassette Basic PlaybackStart playback Changing display information Basic Playback Features22 EN Checking tape positionAutomatic operations after Adjusting tracking conditionSelecting monitor sound Locating beginning24 EN Locating beginning of timerAdjusting picture condition Recordings Instant ReviewSet tape speed Basic RecordingSelect recording channel Start recordingSpecifying recording length Basic Recording Features26 EN Watching one program while recording anotherDisplay VCR status on TV screen Select S-VHS ET modeShowing on-screen display Exit on-screen displayLocating particular scene Special Effect Playback28 EN Rapidly Picture Search High-Speed Picture SearchViewing slow motion picture Viewing still pictureSkipping unwanted portions Pause during playback30 EN VCR Plus+ Timer ProgramingDaily M-F Power Weekly Press the appropriateInput receiving channel number Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Press SP/EP32 EN Changing VCR Plus+ SettingVCR Plus+ guide channel matching Access Guide Channel Set screen Input guide channel number34 EN Express Timer ProgramingDaily Power Set program stop timeCatv To timer-record daily Monday-Friday or weekly serialsOFF DBSChecking program settings 36 ENSelect program to modify Confirm overlapping programsOverlapping programs blink on the screen Change setting Useful Function SettingsAccess Function Set screen 38 ENWhen this function is set to on When this function is set to OFF40 EN Entire program while timer-recording in SP modeFor Example VHS picture quality Mode is used for recording on S-VHS tapesVia their AV Compulink connectors becomes possible Remote Pause terminal. pg42 EN Purpose before you start the editing procedure pg toTo cancel the editing function, select REC-PAUSE This VCRPower Timer Child LockConnection Edit From Camcorder44 EN Various connection for editing tapesSelect video input terminal Select input mode on this VCRMake connections Set Picture Control to Edit46 EN Select edit modeEdit To Or From Another Load cassettesLocate start point Select input modeAudio Dubbing Start audio dubbingInsert Editing Source tape Edited tape 48 ENAnother VCR for playback AV Dubbing Source tape Edited tapeSelect editing function you want Activate editing modePrepare tapes Locate end pointTurn on the TV TV Brand Setting50 EN Set TV brand codeEnter cable box brand code Cable Box Brand SettingTurn on the cable box Operate cable boxTurn on the DBS receiver DBS Receiver Brand Setting52 EN Enter DBS receiver brand codeUnplug VCR Changing Remote Control CodeSet remote control code for Remote Plug in VCRTroubleshooting 54 ENTimer Recording Other Problems 56 ENCan the VCR indefinitely remain in still mode? What happens if the tape reaches its end during recording?58 EN List of termsFront panel Front display panelRear panel 60 ENOn-screen display How to use the Remote RemoteOperating position Horizontal only 62 ENUsable cassettes Full-Size VHS 30 ST-30HOW to Locate Your JVC Service Center Limited Warranty 64 ENMemo 66 EN Page HR-S7800U