JVC HR-S7800U manual 20 EN, Access DBS Receiver Brand Set screen, Enter DBS Receiver’s brand

Page 20

DBS RECEIVER BRAND SET

51

DID YOUR DBS RECEIVER CHANGE TO CHANNEL 100? =YES

NO

PRESS (5,°), THEN (OK)

PRESS (MENU) TO END

DBS RECEIVER BRAND SET

4 0

PRESS NUMBER KEY (0–9)

THEN (OK) TO TEST PRESS (MENU) TO END

20 EN

INITIAL SETTINGS (cont.)

					6		6
					6		7
							7
							FF
POWER					MENU
						PLAY
	DIGITAL TBC/NR
S-VIDEO	VIDEO (MONO)L—AUDIO—R
	S-VHS ET	SP	EP	CH	REC	STOP/EJECT	PAUSE
			VCR		OK

Access DBS Receiver Brand Set screen

Press OK.

Enter DBS Receiver’s brand

On the Remote ONLY:

Press the appropriate Number keys to enter the brand code from the following list, then press OK.

The program currently received through the

DBS receiver appears for about 10 seconds.

1 2 3

2

4 5 6 7

7 8 9

0 4

1

67

OK

SHUTTLE PLUS %Þ

BRAND	CODE
JVC (DISH Network)	51
ECHOSTAR (DISH Network)	51
PRIMESTAR	50
SONY (DSS)	41
RCA (DSS)	40

If the DBS receiver’s channel changes to the channel listed below for your brand, setting is complete

JVC = 100 ECHOSTAR = 100 PRIMESTAR = 55 SONY = 205 RCA = 205

Press OK and “DBS

RECEIVER CONTROL IS ON” appears on the screen for about 5 seconds, then it returns to the normal screen.

If the DBS receiver’s channel does not change as shown above

1Press SHUTTLE PLUS %Þ (or CH 5° on the front panel) to move the highlight bar (arrow) to “NO”.

2Press OK.

3Re-enter the correct code.

NOTES:

The Controller may not work with all types of DBS receiver. If your DBS receiver does not respond to the code, you cannot use the Controller to change satellite channels. In this case, make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start time of timer recording.

The VCR can only change the satellite channel through the Controller during timer recording.

If your DBS receiver cannot be operated with a remote control (because it has no remote sensor), you cannot use the Controller to change its channels. Make sure to leave the DBS receiver turned on and tuned to the proper channel before the scheduled start time of timer recording.

For customers in U.S.A.: If you are unable to set the Controller, contact JVC toll free at 1-800-252-5722.

Image 20

Contents HR-S7800U Dear Customer Telephone NumberPower Sources Power LinesPower Cord Protection Grounding or PolarizationAccessories Damage Requiring ServiceCleaning Replacement PartsContents Basic Connections AntennaVideo OUT Back of VCRConnect VCR to TV Check contents Final preparation for useSituate VCR Plug & Play Setting Perform Plug & Play setupWhat to do if Plug & Play setting failed Clock and tuner channels will be set automaticallyLanguage Setting Select languageReturn to normal screen Press MenuClock Setting Access Main Menu screenAccess clock set screen 10 ENSetting clock semiautomatically Select D.S.T. modeSet Auto Clock to on Select host channelSetting clock manually 12 ENManual Clock Set To make corrections any time during the processTuner Setting Setting channels automaticallyAccess Tuner Set screen Perform Auto Channel SetSetting channels manually Access Manual Channel Set screen14 EN Add or skip desired channelsCable Box Control Setting Installing ControllerSituate Controller Attach ControllerSetting cable box output channel & brand 16 EN If the cable box’s channel does not change to AccessPress OKCable. Box Brand Set screen Enter cable box brand How to control the DBS receiver 18 ENConnect DBS receiver to VCR Antenna VideoSetting DBS receiver output channel & brand Access DBS Receiver Set screenTurn on DBS receiver Select DBS receiver output channelAccess DBS Receiver Brand Set screen 20 ENEnter DBS Receiver’s brand Shuttle Plus %ÞStart playback Basic PlaybackLoad a cassette Basic Playback Features 22 ENChanging display information Checking tape positionAdjusting tracking condition Selecting monitor soundAutomatic operations after Locating beginningLocating beginning of timer Adjusting picture condition24 EN Recordings Instant ReviewBasic Recording Select recording channelSet tape speed Start recordingBasic Recording Features 26 ENSpecifying recording length Watching one program while recording anotherSelect S-VHS ET mode Showing on-screen displayDisplay VCR status on TV screen Exit on-screen displaySpecial Effect Playback 28 ENLocating particular scene Rapidly Picture Search High-Speed Picture SearchViewing still picture Skipping unwanted portionsViewing slow motion picture Pause during playbackVCR Plus+ Timer Programing Daily M-F Power Weekly30 EN Press the appropriateEngage timer recording standby mode To use the VCR while it is in timer recording standby modeInput receiving channel number Press SP/EPVCR Plus+ guide channel matching Changing VCR Plus+ Setting32 EN Access Guide Channel Set screen Input guide channel numberExpress Timer Programing Daily Power34 EN Set program stop timeTo timer-record daily Monday-Friday or weekly serials OFFCatv DBSChecking program settings 36 ENOverlapping programs blink on the screen Confirm overlapping programsSelect program to modify Useful Function Settings Access Function Set screenChange setting 38 ENWhen this function is set to on When this function is set to OFFFor Example Entire program while timer-recording in SP mode40 EN Mode is used for recording on S-VHS tapes Via their AV Compulink connectors becomes possibleVHS picture quality Remote Pause terminal. pgPurpose before you start the editing procedure pg to To cancel the editing function, select REC-PAUSE42 EN This VCRPower Timer Child LockEdit From Camcorder 44 ENConnection Various connection for editing tapesSelect input mode on this VCR Make connectionsSelect video input terminal Set Picture Control to EditSelect edit mode Edit To Or From Another46 EN Load cassettesSelect input mode Audio DubbingLocate start point Start audio dubbing48 EN Another VCR for playbackInsert Editing Source tape Edited tape AV Dubbing Source tape Edited tapeActivate editing mode Prepare tapesSelect editing function you want Locate end pointTV Brand Setting 50 ENTurn on the TV Set TV brand codeCable Box Brand Setting Turn on the cable boxEnter cable box brand code Operate cable boxDBS Receiver Brand Setting 52 ENTurn on the DBS receiver Enter DBS receiver brand codeChanging Remote Control Code Set remote control code for RemoteUnplug VCR Plug in VCRTroubleshooting 54 ENTimer Recording Other Problems 56 ENCan the VCR indefinitely remain in still mode? What happens if the tape reaches its end during recording?58 EN List of termsFront panel Front display panelOn-screen display 60 ENRear panel How to use the Remote Remote62 EN Usable cassettesOperating position Horizontal only Full-Size VHS 30 ST-30HOW to Locate Your JVC Service Center Limited Warranty 64 ENMemo 66 EN Page HR-S7800U