JVC HR-S7800U 18 EN, Connect DBS receiver to VCR, How to control the DBS receiver, Antenna Video

Page 18

18 EN

INITIAL SETTINGS (cont.)

DBS Receiver Control Setting

Suggested location

Place the DBS (Direct Broadcast Satellite) receiver on top of the VCR. Attach the VCR’s Controller to the top of the VCR with the Controller’s transmitter pointed towards the DBS receiver’s remote sensor.

ATTENTION:

The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the Controller so its signal reaches the remote sensors on both the DBS receiver and cable box.

DBS receiver

Controller

Your VCR(suggested

locations)

DBS receiver

Controller

 

To

To

RF output

Audio/Video

Transmitter

output

or

To

To

AUDIO/

ANTENNA IN

VIDEO IN

The following procedure is required if you receive satellite channels through a DBS (Direct Broadcast Satellite) receiver. The Controller allows the VCR to automatically switch the DBS receiver’s channels during timer recording.

NOTES:

The VCR can automatically change the DBS receiver channels using the Controller when the VCR has been programed using Express timer programing ( pg. 34). Because satellite programing does not use PlusCode, the Controller cannot change the DBS receiver channels during VCR Plus+ timer recording.

If a cable box is also used, it is recommended that you connect the DBS receiver to your VCR’s audio/video input connectors and the cable box to your VCR’s antenna input terminal.

Installing Controller

1 Situate Controller

Place the Controller so that its transmitter is facing the DBS receiver’s remote sensor.

Make sure the path between the Controller and the DBS receiver’s remote sensor is not blocked.

2 Attach Controller

Fix securely using the adhesive strip attached on the back of the Controller.

3 Connect DBS receiver to VCR

If your DBS receiver does not have audio/ video output connectors

Connect the RF output terminal on the DBS receiver to the ANTENNA IN terminal on the rear of your VCR.

If your DBS receiver has audio/video output connectors

Connect an audio/video cable between the AUDIO/VIDEO IN connectors on the rear of the VCR and the audio/video output connectors on the DBS receiver.

Your VCR

CABLE

BOX

NOTE:

When connecting your DBS receiver, refer to its instruction manual.

4 Connect Controller to VCR Connect the Controller to the CABLE BOX Controller connector on the rear panel.

How to control the DBS receiver

This VCR has two separate methods to control your DBS receiver.

The VCR’s wireless Remote can control your DBS receiver. This eliminates the need for a separate DBS receiver’s Remote. The VCR’s Controller can also control your DBS receiver. This allows the VCR to change your DBS receiver’s channel number during timer-recording.

Each method must be set up separately. To set up the VCR’s Remote, refer to page 52. To set up the Controller, go to page 19.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents HR-S7800U Dear Customer Telephone NumberPower Cord Protection Power SourcesPower Lines Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Video OUT Basic ConnectionsAntenna Back of VCRCheck contents Final preparation for use Situate VCRConnect VCR to TV What to do if Plug & Play setting failed Plug & Play SettingPerform Plug & Play setup Clock and tuner channels will be set automaticallyReturn to normal screen Language SettingSelect language Press MenuAccess clock set screen Clock SettingAccess Main Menu screen 10 ENSet Auto Clock to on Setting clock semiautomaticallySelect D.S.T. mode Select host channelManual Clock Set Setting clock manually12 EN To make corrections any time during the processAccess Tuner Set screen Tuner SettingSetting channels automatically Perform Auto Channel Set14 EN Setting channels manuallyAccess Manual Channel Set screen Add or skip desired channels Situate Controller Cable Box Control Setting Installing Controller Attach ControllerSetting cable box output channel & brand 16 ENAccessPress OKCable. Box Brand Set screen Enter cable box brandIf the cable box’s channel does not change to Connect DBS receiver to VCR How to control the DBS receiver18 EN Antenna VideoTurn on DBS receiver Setting DBS receiver output channel & brandAccess DBS Receiver Set screen Select DBS receiver output channelEnter DBS Receiver’s brand Access DBS Receiver Brand Set screen20 EN Shuttle Plus %ÞBasic Playback Load a cassetteStart playback Changing display information Basic Playback Features22 EN Checking tape positionAutomatic operations after Adjusting tracking conditionSelecting monitor sound Locating beginning24 EN Locating beginning of timerAdjusting picture condition Recordings Instant ReviewSet tape speed Basic RecordingSelect recording channel Start recordingSpecifying recording length Basic Recording Features26 EN Watching one program while recording anotherDisplay VCR status on TV screen Select S-VHS ET modeShowing on-screen display Exit on-screen displayLocating particular scene Special Effect Playback28 EN Rapidly Picture Search High-Speed Picture SearchViewing slow motion picture Viewing still pictureSkipping unwanted portions Pause during playback30 EN VCR Plus+ Timer ProgramingDaily M-F Power Weekly Press the appropriateInput receiving channel number Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Press SP/EPChanging VCR Plus+ Setting 32 ENVCR Plus+ guide channel matching Access Guide Channel Set screen Input guide channel number34 EN Express Timer ProgramingDaily Power Set program stop timeCatv To timer-record daily Monday-Friday or weekly serialsOFF DBSChecking program settings 36 ENConfirm overlapping programs Select program to modifyOverlapping programs blink on the screen Change setting Useful Function SettingsAccess Function Set screen 38 ENWhen this function is set to on When this function is set to OFFEntire program while timer-recording in SP mode 40 ENFor Example VHS picture quality Mode is used for recording on S-VHS tapesVia their AV Compulink connectors becomes possible Remote Pause terminal. pg42 EN Purpose before you start the editing procedure pg toTo cancel the editing function, select REC-PAUSE This VCRPower Timer Child LockConnection Edit From Camcorder44 EN Various connection for editing tapesSelect video input terminal Select input mode on this VCRMake connections Set Picture Control to Edit46 EN Select edit modeEdit To Or From Another Load cassettesLocate start point Select input modeAudio Dubbing Start audio dubbingInsert Editing Source tape Edited tape 48 ENAnother VCR for playback AV Dubbing Source tape Edited tapeSelect editing function you want Activate editing modePrepare tapes Locate end pointTurn on the TV TV Brand Setting50 EN Set TV brand codeEnter cable box brand code Cable Box Brand SettingTurn on the cable box Operate cable boxTurn on the DBS receiver DBS Receiver Brand Setting52 EN Enter DBS receiver brand codeUnplug VCR Changing Remote Control CodeSet remote control code for Remote Plug in VCRTroubleshooting 54 ENTimer Recording Other Problems 56 ENCan the VCR indefinitely remain in still mode? What happens if the tape reaches its end during recording?58 EN List of termsFront panel Front display panel60 EN Rear panelOn-screen display How to use the Remote RemoteOperating position Horizontal only 62 ENUsable cassettes Full-Size VHS 30 ST-30HOW to Locate Your JVC Service Center Limited Warranty 64 ENMemo 66 EN Page HR-S7800U
Top Page Image Contents