JVC HR-S6722EK setup guide OUTPUT/INPUT Setting, SELECT/INPUT Setting

Page 36

36ADVANCEDOPERATIONS(cont.)

L-1 OUTPUT/INPUT Setting

The AV1 (L-1) IN/OUT connector accepts and delivers either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set "L-1 OUTPUT" and "L-1 INPUT" to the appropriate mode depending on the type of unit connected to the rear panel AV1 (L-1) IN/OUT connector of this recorder.

1Press MENU to access the Main Menu screen.

2Press %Þ to move the highlight bar (pointer) to "OUTPUT/INPUT SET", then press OK or #.

3 Press %Þ to move the highlight bar (pointer) to "L-1 OUTPUT" or "L-1 INPUT".

4 For "L-1 OUTPUT"

Press OK or #to select "VIDEO" or "S-VIDEO".

a–VIDEO

: If a connected device's input is compatible only with regular video signals,

 

set to "VIDEO".

b–S-VIDEO

: If a connected device's input is compatible with Y/C signals, set to

 

"S-VIDEO". This setting will let you take advantage of higher-quality

 

S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that

 

is compatible with the Y/C signal.)

For "L-1 INPUT"

Press OK or #to select "VIDEO" or "S-VIDEO".

a–VIDEO

: If a connected device's output is compatible only with regular video

 

signals, set to "VIDEO".

b–S-VIDEO

: If a connected device's output is compatible with Y/C signals, set to

 

"S-VIDEO". This setting will let you take advantage of higher-quality

 

S-VHS pictures. (For connection, be sure to use a 21-pin SCART cable that

 

is compatible with the Y/C signal.)

5Press MENU to return to normal screen.

●If "L-1 OUTPUT" is set to "S-VIDEO", it is impossible to set "L-1 INPUT" to "S-VIDEO".

●If "L-2 SELECT" is set to "DECODER", it is impossible to set "L-1 INPUT" to "S-VIDEO".

 

OUTPUT/INPUT SET

 

 

L-1 OUTPUT

VIDEO

L-1

INPUT

VIDEO

L-2

SELECT

A/V

L-2

INPUT

VIDEO

[5°] = [MENU] : EXIT

L-2 SELECT/INPUT Setting

The AV2 (L-2) IN/DECODER connector accepts either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set "L-2 SELECT" to the appropriate mode depending on the type of unit connected to the rear panel AV2 (L-2) IN/DECODER connector of this recorder. Set "L-2 INPUT" to the appropriate mode depending on the output signals of the connected unit.

1Press MENU to access the Main Menu screen.

2Press %Þ to move the highlight bar (pointer) to "OUTPUT/INPUT SET", then press OK or #.

3 Press %Þ to move the highlight bar (pointer) to "L-2 SELECT" or "L-2 INPUT".

4 For "L-2 SELECT"

OUTPUT/INPUT SET

Press OK or #to select "A/V", "DECODER" or "SAT".

L-1 OUTPUT

VIDEO

a–A/V

: To use this recorder as the recording deck with the player connected to the

L-1 INPUT

VIDEO

 

AV2 (L-2) IN/DECODER connector, or to use the satellite receiver con-

 

 

 

 

L-2 SELECT

A/V

 

 

nected to the AV2 (L-2) IN/DECODER connector.

 

b–DECODER

L-2 INPUT

VIDEO

 

: To use a decoder connected to the AV2 (L-2) IN/DECODER connector.

 

 

 

c–SAT

: To view a satellite programme with the TV set while the recorder is turned

 

 

 

 

off. (☞ pg. 30)

 

 

 

 

[5°] =

 

 

For "L-2 INPUT"

[MENU] : EXIT

 

 

Press OK or #to select "VIDEO" or "S-VIDEO".

 

 

 

a–VIDEO

: If a connected device's output is compatible only with regular video

 

 

 

 

signals, set to "VIDEO".

 

 

 

b–S-VIDEO

: If a connected device's output is compatible with Y/C signals, set to

 

 

 

 

"S-VIDEO". This setting will let you take advantage of higher-quality S-VHS

 

 

 

 

pictures. (For connection, be sure to use a 21-pin SCART cable that is

 

 

 

 

compatible with the Y/C signal.)

 

 

 

5Press MENU to return to normal screen.

●If you have a satellite receiver or a decoder connected to the AV2 (L-2) IN/DECODER connector, be sure to set "L-2 SELECT" back to appropriate mode after editing.

●If you're not connecting a satellite receiver or a decoder to the AV2 (L-2) IN/DECODER connector, leave "L-2 SELECT" set to "A/V".

●The default setting is "A/V"; if the recorder's memory backup has expired due to a power cut or because the AC was removed from the recorder, "A/V" will be automatically selected when the power is restored to the recorder. If you are using a satellite receiver or a decoder, be sure to set "L-2 SELECT" back to appropriate mode.

●When "L-2 SELECT" is set to "SAT", "SAT" appears on screen or display panel instead of "L-2" or "L2".

●If "L-2 SELECT" is set to "DECODER", it is impossible to set "L-2 INPUT" to "S-VIDEO".

●If "L-1 OUTPUT" is set to "S-VIDEO", it is impossible to set "L-2 SELECT" to "DECODER".

Page 35 Page 37
Image 36
Page 35 Page 37
Contents HR-S6722EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide To connect to a TV with 21-pin AV input connector Scart Back of TVBack of Recorder Mains outlet Mains Power Cord Video ConnectionBefore performing the following procedure, make sure that Auto for Auto Set Up functionRefer to With the AV or S-VIDEO connection Tion pg and the TV is turned on,Or remote control until the display panel Shows either the display as illustrated onProgress, this process will be interrupted You will need to start again. See Notes belowIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTV Auto Power On Link FunctionsTurn on the Recorder NexTView LinkSatellite Receiver Control Setting Access SAT Control SET Screen Enter Satellite RECEIVER’S BrandCheck Result of Test Playback Load a CassetteFind Programme Start Point Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingEnter Programme Start Time TimeSET PDC Mode Timer ModeReturn to Normal Engage RECORDER’SCheck, Cancel And Replace Programmes Access Programme SCREEN/ DisplayCancel or Replace a Programme Return to Timer ModeWhen programmes overlap each other Cancel or Change Programme SettingTo cancel a programme Confirm Overlapping ProgrammesPlayback Picture Adjustment Adjust TrackingOverride Automatic Tracking ManuallySelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackLooking For Scene You Want Activate Index SearchActivate Instant Review Skip Over UnwantedRecording According To Tape Type Super VHS S-VHS VHS ET and VHSPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemRecording PlaybackOr press Record on the recorder Connector TV Aerial cable Audio in connector Automatic Satellite Programme RecordingSatellite Receiver Unit AerialAccess Main Menu Screen Select L-2 Select ModeREC Mode ScreenAccess Main Menu Screen Access Mode SET ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Input Mode SET Edit ModeEdit To Or From Another Video Recorder SET Recording DECK’SRecorder Player OUTPUT/INPUT Setting SELECT/INPUT SettingENABLE/DISABLE ON-SCREEN Display Other FunctionsOn-Screen Display Power Save Mode Power SAVE, then pressAuto Timer Auto SP→LP TimerNext Function Memory Repeat Playback Ntsc PlaybackActivate Repeat Playback Connection To Stereo System Speaker Television Mains outletClock Set Just ClockVideo Plus+ Setup NumberGuide Program Number Set Access Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Tuner Set Perform Auto Channel SETAuto Channel Set Screen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Select BandInput Channel Enter NEW Channel InformationWhen Receiving a Scrambled Broadcast Change Station Preset PositionFine-Tuning Channels Already Stored Delete a ChannelAccess Manual Switch StationsChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide Questions And Answers Ä remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Ejected, and ä and on Record Safety tab removed Tape-to-tape editing is not possibleWon’t stop Index Front ViewAudio OUT L/R Connectors enable Tape Speed Indicators display mode of recording lightRemote Control Fast Forward FF Button fast-forwards tape VCR, TV PR +/-,TV +/-, TV MutingMaximum recording time DA4 Double Azimuth helical
Top Page Image Contents