JVC HR-S6722EK setup guide Tape-to-tape editing is not possible, Won’t stop

							55
3.	Tape-to-tape editing is not possible.		● The source (another video recorder,		Confirm that the source is properly
			camcorder) has not been properly		connected.
			connected.
			● All necessary power switches have		Confirm that all units’ power switches
			not been turned on.		are turned on.
			● The input mode is not correct.		Set the input mode to “L-1”,“L-2”,
					“F-1” or “S-1”.
4.	Camcorder recording is not		● The camcorder has not been		Confirm that the camcorder is
	possible.		properly connected.		properly connected.
			● The input mode is not correct.		Set the input mode to “L-1”,“L-2”,
					“F-1” or “S-1”.
TIMER RECORDING
		SYMPTOM		POSSIBLE CAUSE		CORRECTIVE ACTION
1.	Timer recording won’t work.		● The clock and/or the timer have		Re-perform the clock and/or timer
			been set incorrectly.		settings.
			● The timer is not engaged.		Press ä and confirm that “ä“ is
					displayed on the display panel.
2.	Timer programming is not possible.		● Timer recording is in progress.		Timer programming can’t be
					performed while a timer recording is
					in progress. Wait until it finishes.
3.	“ä“ and “]“ on the display		● The timer is engaged but there’s no		Load a cassette with the Record
	panel won’t stop blinking.		cassette loaded.		Safety tab intact, or cover the hole
					using adhesive tape.
4.	The cassette is automatically		● The loaded cassette has had its		Remove the cassette and cover the hole
	ejected, and “ä“ and “]“ on the		Record Safety tab removed.		with adhesive tape, or insert a cassette
	display panel won’t stop blinking.				with the Record Safety tab intact.
5.	“ä“ blinks for 10 seconds and the		● ä has been pressed when there are		Check the programmed data and re-
	Timer mode is disengaged.		no programs in memory, or the timer		programme as necessary, then press
			record information has been		ä again.
			programmed incorrectly.
6.	The cassette is automatically		● The end of the tape was reached		The programme may not have been
	ejected, the power shuts off and		during timer recording.		recorded in its entirety. Next time make
	“ä“ and “]“ won’t stop				sure you have enough time on the tape
	blinking.				to record the entire programme.
7.	The VIDEO Plus+ system does not		● The recorder’s preset positions have		Refer to "Guide Program Number Set"
	timer-record properly.		been set incorrectly.		and re-perform the procedure (☞ pg. 43).
OTHER PROBLEMS
		SYMPTOM		POSSIBLE CAUSE		CORRECTIVE ACTION
1.	Whistling or howling is heard from		● The camcorder’s microphone is too		Position the camcorder so its
	the TV during camcorder record-		close to the TV.		microphone is away from the TV.
	ing.		● The TV’s volume is too high.		Turn the TV’s volume down.
2.	When scanning channels, some of		● Those channels have been desig-		If you need the skipped channels,
	them are skipped over.		nated to be skipped.		restore them (☞ pg. 48).
3.	The preset cannot be changed.		● Recording is in progress.		Press PAUSE to pause the recording,
					change presets, then press PLAY to
					resume recording.
4.	Channel settings that were made		● After the manual settings were		Perform manual setting again.
	manually seem to have changed or		made, Auto Channel Set was
	disappeared.		performed.
5.	No channels are stored in the		● The TV aerial cable was not		Turn off the recorder once and connect
	recorder's memory.		connected to the recorder when		the TV aerial cable to the recorder
			Auto Set Up was performed.		properly, then turn on the recorder
					again. The recorder will try Auto Set
					Up again (☞ pg. 8).
			● The fully-wired 21-pin SCART cable		Turn off the recorder once and connect
			was not connected between TV and		the fully-wired 21-pin SCART cable to
			the recorder when Preset Download		the recorder properly, then turn on the
			was performed.		recorder again. Then perform Preset
					Download again (☞ pg. 9).