JVC HR-S6722EK setup guide With RF Connection

Page 45

STOP

– –:– –

1 2 3

2

4 5 6

7 8 9

4

0

PR

1 ?

3

OK

TEST SIGNAL

The channel on which the screen on the left appears clearly in step 2 is your Video Channel.

45

With RF Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■the connected TV is turned on.

■batteries have been installed in the remote control.

ACCESS VIDEO CHANNEL

SET MODE

1 Press and hold down STOP on the recorder until the display panel shows the following.

SET VIDEO CHANNEL

2 Press PR+ or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area. Refer to list on page 52 for details of broadcast stations in your area.

(Ex.) If channel 36 is available in your area

Then set your TV to UHF channel 36. (Refer to the instructions supplied with your TV set for how to do this.)

●If the two vertical white bars appear clearly on the screen as shown in the illustration at bottom left, go to step 3.

●If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

IMPORTANT

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

EXIT VIDEO CHANNEL SET

MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to the Video Channel.

Image 45

Contents HR-S6722EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide To connect to a TV with 21-pin AV input connector Scart Back of TVBack of Recorder Video Connection Mains outlet Mains Power CordAuto for Auto Set Up function Before performing the following procedure, make sure thatRefer to With the AV or S-VIDEO connection Tion pg and the TV is turned on,Shows either the display as illustrated on Or remote control until the display panelProgress, this process will be interrupted You will need to start again. See Notes belowIf both auto channel set and auto clock set have failed If auto channel set has succeeded but auto clock set has notLink Functions TV Auto Power OnTurn on the Recorder NexTView LinkSatellite Receiver Control Setting Access SAT Control SET Screen Enter Satellite RECEIVER’S BrandCheck Result of Test Load a Cassette PlaybackFind Programme Start Point Start PlaybackActivate HIGH-SPEED Search Pause During PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayAccess Video PLUS+ Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Program Screen Enter Pluscode NumberPDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET PDC ModeReturn to Normal Engage RECORDER’SAccess Programme SCREEN/ Display Check, Cancel And Replace ProgrammesCancel or Replace a Programme Return to Timer ModeCancel or Change Programme Setting When programmes overlap each otherTo cancel a programme Confirm Overlapping ProgrammesAdjust Tracking Playback Picture AdjustmentOverride Automatic Tracking ManuallyReceiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackActivate Index Search Looking For Scene You WantActivate Instant Review Skip Over UnwantedSuper VHS S-VHS VHS ET and VHS Recording According To Tape TypeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsRecording PlaybackOr press Record on the recorder Automatic Satellite Programme Recording Connector TV Aerial cable Audio in connectorSatellite Receiver Unit AerialSelect L-2 Select Mode Access Main Menu ScreenREC Mode ScreenAccess Mode SET Screen Access Main Menu ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder SET Edit Mode Input ModeEdit To Or From Another Video Recorder SET Recording DECK’SRecorder Player SELECT/INPUT Setting OUTPUT/INPUT SettingENABLE/DISABLE ON-SCREEN Display Other FunctionsOn-Screen Display Power SAVE, then press Power Save ModeAuto Timer Auto SP→LP TimerNext Function Memory Repeat Playback Ntsc PlaybackActivate Repeat Playback Speaker Television Mains outlet Connection To Stereo SystemJust Clock Clock SetVideo Plus+ Setup NumberGuide Program Number Set Exit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Tuner Set Perform Auto Channel SETAuto Channel Set Procedures Screen preset positionsAfter Scan Completed Is displayed on the screenSelect Band Storing Channels ManuallyInput Channel Enter NEW Channel InformationChange Station Preset Position When Receiving a Scrambled BroadcastFine-Tuning Channels Already Stored Delete a ChannelSwitch Stations Access ManualChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide Questions And Answers Ä remain lit on the display panel. Is there Problem?What happens if the tape runs out during recording? Troubleshooting Ejected, and ä and on Record Safety tab removed Tape-to-tape editing is not possibleWon’t stop Front View IndexTape Speed Indicators display mode of recording light Audio OUT L/R Connectors enableRemote Control VCR, TV PR +/-,TV +/-, TV Muting Fast Forward FF Button fast-forwards tapeDA4 Double Azimuth helical Maximum recording time