JVC HR-S6722EK setup guide Ntsc Playback, Activate Repeat Playback

Page 40

40ADVANCEDOPERATIONS(cont.)

Repeat Playback

Your video recorder can automatically play back the whole tape 100 times repeatedly.

– –:– –

1

4

7

1

LAY

REW

STOP

2 3

2

56

89

4

0

?

3

 

1

 

START PLAYBACK

 

 

Press PLAY.

 

2

 

ACTIVATE REPEAT PLAYBACK

 

 

Press PLAY and hold for over 5 seconds, then release.

 

 

 

 

 

● The Play indicator ( ) on the display panel blinks

 

 

slowly.

 

 

 

● The tape plays 100 times automatically, and then

 

 

 

stops.

 

 

 

 

FF

3

 

STOP PLAYBACK

 

 

PAUSE

 

Press STOP at any time to stop playback.

 

 

 

 

 

 

 

 

 

 

NOTE:

 

Pressing PLAY, REW, FF or PAUSE also stops Repeat Playback.

NTSC Playback

Your video recorder is equipped with NTSC circuitry that can play back NTSC tapes.

1

2

LOAD A CASSETTE

Insert a cassette recorded in NTSC.

START PLAYBACK

Press PLAY.

●"NTSC→PAL" appears on the screen for about 5 seconds.

●Some TVs shrink the picture vertically and place black bars at the top and bottom of the screen. This is not a malfunction on the part of either the video recorder or the TV.

●The picture may roll up and down. This can be corrected using the V-HOLD control found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD control.)

●The counter and tape remaining time readings will be incorrect.

●During search, still, or frame-by-frame playback, the picture will be distorted, and there may be a loss of colour.

●Depending on the type of TV, the top and bottom portions of superimposed displays may be cut off during NTSC playback.

Page 39 Page 41
Image 40
Page 39 Page 41
Contents
HR-S6722EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV To connect to a TV with 21-pin AV input connector ScartBack of Recorder Mains outlet Mains Power Cord Video ConnectionBefore performing the following procedure, make sure that Auto for Auto Set Up functionRefer to With the AV or S-VIDEO connection Tion pg and the TV is turned on,Or remote control until the display panel Shows either the display as illustrated onProgress, this process will be interrupted You will need to start again. See Notes belowIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTV Auto Power On Link FunctionsTurn on the Recorder NexTView LinkSatellite Receiver Control Setting Enter Satellite RECEIVER’S Brand Access SAT Control SET ScreenCheck Result of Test Playback Load a CassetteFind Programme Start Point Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingEnter Programme Start Time TimeSET PDC Mode Timer ModeReturn to Normal Engage RECORDER’SCheck, Cancel And Replace Programmes Access Programme SCREEN/ DisplayCancel or Replace a Programme Return to Timer ModeWhen programmes overlap each other Cancel or Change Programme SettingTo cancel a programme Confirm Overlapping ProgrammesPlayback Picture Adjustment Adjust TrackingOverride Automatic Tracking ManuallySelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackLooking For Scene You Want Activate Index SearchActivate Instant Review Skip Over UnwantedRecording According To Tape Type Super VHS S-VHS VHS ET and VHSPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemPlayback RecordingOr press Record on the recorder Connector TV Aerial cable Audio in connector Automatic Satellite Programme RecordingSatellite Receiver Unit AerialAccess Main Menu Screen Select L-2 Select ModeREC Mode ScreenAccess Main Menu Screen Access Mode SET ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Input Mode SET Edit ModeEdit To Or From Another Video Recorder SET Recording DECK’SRecorder Player OUTPUT/INPUT Setting SELECT/INPUT SettingOther Functions ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Display Power Save Mode Power SAVE, then pressAuto SP→LP Timer Auto TimerNext Function Memory Ntsc Playback Repeat PlaybackActivate Repeat Playback Connection To Stereo System Speaker Television Mains outletClock Set Just ClockNumber Video Plus+ SetupGuide Program Number Set Access Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Perform Auto Channel SET Tuner SetAuto Channel Set Screen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Select BandInput Channel Enter NEW Channel InformationWhen Receiving a Scrambled Broadcast Change Station Preset PositionFine-Tuning Channels Already Stored Delete a ChannelAccess Manual Switch StationsChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide Ä remain lit on the display panel. Is there Problem? Questions And AnswersWhat happens if the tape runs out during recording? Troubleshooting Tape-to-tape editing is not possible Ejected, and ä and on Record Safety tab removedWon’t stop Index Front ViewAudio OUT L/R Connectors enable Tape Speed Indicators display mode of recording lightRemote Control Fast Forward FF Button fast-forwards tape VCR, TV PR +/-,TV +/-, TV MutingMaximum recording time DA4 Double Azimuth helical
Related manuals
Manual 60 pages 43.25 Kb