JVC HR-S6722EK setup guide Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 44

44SUBSIDIARYSETTINGS(cont.)

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

STOP

IMPORTANT

Perform the following steps only if —

—Video Channel Set has not been done correctly by the Auto Set Up function (☞ pg. 8).

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.

●If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection), or via the provided RF cable, an S-Video cable and an audio cable (S-VIDEO connection), you do not need the video channel so you have to set the video channel to off. — Go to "With AV or S-VIDEO Connection" below.

●If you have connected the video recorder to your TV via the provided RF cable only (RF connection), you have to set the correct video channel — Go to "With RF Connection" on page 45.

– –:– –

1 2 3

2

4 5 6

7 8 9

4

0

PR

1 ?

3

OK

With AV or S-VIDEO

Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■batteries have been installed in the remote control.

ACCESS VIDEO CHANNEL SET MODE

		Press and hold down STOP on the recorder until the
	1 display panel shows the following.
	2	SET VIDEO CHANNEL
	2	Press PR – until the display panel shows "–OUT– –".
		Press PR – until the display panel shows "–OUT– –".

●Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this.

Image 44

Contents HR-S6722EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of Recorder To connect to a TV with 21-pin AV input connector ScartBack of TV Mains outlet Mains Power Cord Video ConnectionBefore performing the following procedure, make sure that Auto for Auto Set Up functionRefer to With the AV or S-VIDEO connection Tion pg and the TV is turned on,Or remote control until the display panel Shows either the display as illustrated onProgress, this process will be interrupted You will need to start again. See Notes belowIf auto channel set has succeeded but auto clock set has not If both auto channel set and auto clock set have failedTV Auto Power On Link FunctionsTurn on the Recorder NexTView LinkSatellite Receiver Control Setting Check Result of Test Access SAT Control SET ScreenEnter Satellite RECEIVER’S Brand Playback Load a CassetteFind Programme Start Point Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingEnter Programme Start Time TimeSET PDC Mode Timer ModeReturn to Normal Engage RECORDER’SCheck, Cancel And Replace Programmes Access Programme SCREEN/ DisplayCancel or Replace a Programme Return to Timer ModeWhen programmes overlap each other Cancel or Change Programme SettingTo cancel a programme Confirm Overlapping ProgrammesPlayback Picture Adjustment Adjust TrackingOverride Automatic Tracking ManuallySelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackLooking For Scene You Want Activate Index SearchActivate Instant Review Skip Over UnwantedRecording According To Tape Type Super VHS S-VHS VHS ET and VHSPlayback/ Recording According To Tape Charac- teristics S.T. Picture SystemOr press Record on the recorder RecordingPlayback Connector TV Aerial cable Audio in connector Automatic Satellite Programme RecordingSatellite Receiver Unit AerialAccess Main Menu Screen Select L-2 Select ModeREC Mode ScreenAccess Main Menu Screen Access Mode SET ScreenSelect Picture Control SET Mode Minimizing Picture Degradation While EditingEdit From Camcorder Input Mode SET Edit ModeEdit To Or From Another Video Recorder SET Recording DECK’SRecorder Player OUTPUT/INPUT Setting SELECT/INPUT SettingOn-Screen Display ENABLE/DISABLE ON-SCREEN DisplayOther Functions Power Save Mode Power SAVE, then pressNext Function Memory Auto TimerAuto SP→LP Timer Activate Repeat Playback Repeat PlaybackNtsc Playback Connection To Stereo System Speaker Television Mains outletClock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Access Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Auto Channel Set Tuner SetPerform Auto Channel SET Screen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Select BandInput Channel Enter NEW Channel InformationWhen Receiving a Scrambled Broadcast Change Station Preset PositionFine-Tuning Channels Already Stored Delete a ChannelAccess Manual Switch StationsChannel SET Screen Select NEW StationTV Station And ID List TV Station Channel Number Guide What happens if the tape runs out during recording? Questions And AnswersÄ remain lit on the display panel. Is there Problem? Troubleshooting Won’t stop Ejected, and ä and on Record Safety tab removedTape-to-tape editing is not possible Index Front ViewAudio OUT L/R Connectors enable Tape Speed Indicators display mode of recording lightRemote Control Fast Forward FF Button fast-forwards tape VCR, TV PR +/-,TV +/-, TV MutingMaximum recording time DA4 Double Azimuth helical