JVC HR-S9850EU specifications Cancel or change a programme, Return to the timer mode

Page 37

EN 37

To cancel or change a programme...

D Cancel or change a programme.

Press & to cancel a programme. To change programme settings, press the appropriate button: START+/–, STOP+/–, DATE+/–, PR+/–, VPS/PDC and/or SP/LP/EP (p).

●You can change “TV PROG” to “SAT” for the channel position by pressing the number key “0”.

●If you do not want to edit the programme title, skip steps 5 and 6.

When programmes overlap each other

If “PROGRAM OVERLAPPED” appears, you have another programme overlapping the programme you have just made. The Programme Check screen appears and conflicting programmes will start blinking.

E Access the Title Edit screen.

Example: Programme 1 (you have just made) and

Press the number key “1”.

Programme 4 overlap each other.

The Title Edit screen appears.

A Confirm the overlapping programmes.

● You can access the title edit

screen only when

“NAVIGATION” is set to

Overlapping programmes blink on the TV screen.

“ON”. ( pg. 43)

B Select the programme to modify.

F Enter the programme title.

Press the number keys and e to enter characters, then press OK. For details, refer to “Entering Character” on page 45.

Press rt, then press OK or e.

●You can only select one of the overlapping programmes.

NOTE:

If you do not mind this overlap, press PROG to finish the timer programme setting. The programme with the lower programme number will be recorded and the other one will not be recorded correctly. If no changes are made for approximately 1 minute, the recorder will return to the normal screen.

C Cancel or change programme setting.

G Return to the normal screen/display.

Press " as many times as necessary. If there are still some programmes remaining, go on to step 8.

H Return to the timer mode.

Press # (TIMER).

To cancel a programme, press & when the Programme screen you do not want is shown. “PROGRAM COMPLETED” appears on the TV screen for about 5 seconds, then the normal screen appears.

To change a programme, press the appropriate button: START+/–, STOP+/–, DATE+/–, PR+/–, VPS/PDC and/or SP/LP/EP (p) when the Programme screen on which you want to make changes is shown, then press OK. “PROGRAM COMPLETED” appears on the TV screen for about 5 seconds, then the normal screen appears.

NOTE:

You can also check the programmes on the front display panel even if the recorder’s power is off (unless the recorder is in the Power Save mode  pg. 70) or the recorder is in the Timer mode; however, it is not possible to cancel or change the programmes.

NOTE:

If the overlap is not yet solved, or another overlap occurs with the timer programme setting after making the last correction on a programme, the conflicting programmes will be shown on the Programme Check screen again. Repeat the above steps again until the overlap is solved.

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display Remote Control Remote Control LCD How To Use10 EN Check the contentsSituate the recorder Connect the recorder to TVPlug the end of the mains power cord into a mains outlet 8To connect to a TV with S-VIDEO/AUDIO in connectorsVideo Connection 12 EN Auto Set UpTurn on the recorder Select your countrySelect the language Perform Auto Set UpPress rt to select your language code Press rt to select Auto and press OK or e14 EN Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or eJust Clock Language for the on-screen displayAccess the Country Set screen Access the Main Menu screenLanguage 16 ENSituate the Satellite Controller Installing Satellite ControllerAttach the Satellite Controller Make connections18 EN Setting satellite receivers brand and channelNexTView Link TV Auto Power OnVCR Auto Standby Direct Rec 20 EN Basic PlaybackHigh-Speed Turbo Search Slow MotionPause during playback Activate frame-by-frame playbackVariable Speed Search 22 ENSkip Search Index SearchRepeat Playback Next Function MemoryManual Tracking Soundtrack Selection24 EN Tape Remaining Time Instant Timer Recording ITR26 EN Engage the Record-Pause modeRetake Locate the start pointAdjust the audio recording level Engage the S-VHS ET modeSuper VHS ET S-VHS ET Audio Recording Level ControlOn-screen Display Receiving Stereo and Bilingual ProgrammesReceived Recording PlaybackAccess the Showview screen Access the Showview displayAccess the Showview Program screen 30 ENAccess the Title Edit screen Set the VPS/PDC modeEngage the recorder’s timer mode Enter the programme title32 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+Before performing the 24 Hour Express Timer Programming Enter the programme mode34 EN Set the programme start/stop time and channelYou can programme this recorder to timer-record as many as Access the Programme Check screen/display Disengage the timer modeAccess the Programme screen/display Press # TIMER, then pressReturn to the timer mode Cancel or change a programmeSelect the programme to modify Enter the programme title Programme 4 overlap each otherRecording mode Select the L-2 Select modeProgramme Recording 38 ENSet the remote control code Remote A/B Code SwitchingCheck the remote control code for the recorder Change the code for the recorder40 EN TV Multi-Brand Remote ControlSet the TV brand code Operate the TVSet the satellite receiver brand code Satellite Receiver Multi-Brand Remote ControlOperate the satellite receiver 42 EN NavigationNavigation Playback Check MemoryVideo Navigation Title Screen Turn Off NavigationCheck the memory Turn off NavigationEdit Title Access the Find Blank Space screen44 EN Find Blank SpaceEdit Tape Title Access the Edit Title screenEntering Character Select the tape titleChoice of Category 46 ENSelect the programme Select the categoryDelete Programme Data Delete Tape DataDelete the tape data Delete the programme dataFind Title Access the Find Title screen48 EN Sort By Tape NumberAccess the Date screen Access the Tape No. screenSort By Date Select the programme50 EN Access the Category screenSort By Category Category you want to watchSet the edit mode Set the recorder’s input modeEdit From a Camcorder Start the camcorderOUTPUT/INPUT SET, then Access the Output/Input Set screenPress OK or e Decoder connector Select and L-2 Input Setting54 EN Another Video RecorderRecorder Player 56 EN Audio DubbingPre-recorded tape Audio-dubbed tape CD player, etcStart dubbing Engage the Audio Dubbing modeEnd Audio Dubbing Press AUX number key 0 and/or PR to select F-1 or S-158 EN Insert EditingSource tape Before Insert Editing Recording tape After Insert EditingAV Insert Editing Engage the Insert Editing modeLocate the end point Start Editing60 EN Access the R.A.Edit screenLoad the source cassette Start playback of the source cassettePrepare the recording deck Memory CapacityStart Random Assemble Editing End Random Assemble EditingStart Synchro Editing 62 ENPause Synchro Editing Press Synchro 7/79Set the Jlip ID number Access the Jlip ID No. Set screenJlip ID Number ExamplesSimple Connections Connecting To a Satellite ReceiverSatellite receiver Decoder Back of recorder Perfect Connections66 EN Select the input modeConnect the decoder Set the tunerMake connections Connecting/Using a Stereo SystemAccess the Mode Set screen Mode SetSelect the mode Select the mode settingThis feature helps you to adjust the playback picture You can set the B.E.S.T. Biconditional Equalised SignalWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder isFor Example 70 ENAbout Ntsc Playback Tuner Set Access the Auto Channel Set screen72 EN Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice Manual Channel Set 74 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations a 76 ENSet Stations B Station Name TV Station And ID ListExit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set 78 ENGuide Program Number Set Showview System SetupGuide Program Number Enter the Guide Program numberClock Set Access the Clock Set screen80 EN Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operation82 EN TroubleshootingRecording 84 EN Timer RecordingPlayback 86 EN Manual Tracking Mode Set Auto Set UpAudio Dubbing AV Insert Editing S.T. Picture SystemCountry code International telephone Language code
Top Page Image Contents