JVC HR-S9850EU AV Insert Editing, Locate the end point, Engage the Insert Editing mode

Page 59

EN 59

A Make connections.

Connect the player’s VIDEO OUT or S-VIDEO OUT and AUDIO OUT connectors to your recorder’s VIDEO or S-VIDEO and AUDIO input connectors on the front panel.

B Set the recorder’s input mode.

Press AUX (number key “0”) and/or PR to select “F-1” for the AUDIO and VIDEO input connectors or “S-1” for AUDIO and S-VIDEO input connectors.

C Locate the end point.

Load the recording cassette into your recorder, and play it back to determine the edit-out point (the end of the segment to be replaced) using the JOG dial, or pressing w

eand 9.

D Reset the counter.

Press 0000.

●The counter is reset to “0:00:00”.

E Locate the start point.

Determine the edit-in point (the beginning of the segment to be replaced) using the JOG dial, or pressing w e and 9.

●Be sure to engage the Still mode at the edit-in point.

F Engage the Insert Editing mode.

Press INSERT.

●Your recorder enters the Insert Pause mode. (“o”, “u” and “i” light up on the front display panel.)

●The TV screen changes from the still picture to the input source you are going to record.

G Start Editing.

Load the source cassette and play back the segment that is to be inserted. When you reach the start of the section of the source tape that you wish to insert, press 4 to start the tape in your recorder; Insert Editing begins at this point.

●“o” and “u” are displayed on the front display panel.

H End Insert Editing.

At counter “0:00:00”, Insert Editing will stop automatically while the tape continues running in the Play mode. If you wish to stop Insert Editing before the specified edit-out point, press 0000.

AV Insert Editing

If you want to replace the picture, Hi-Fi audio soundtrack and normal audio soundtrack all at the same time ...

... In step 6, after you press INSERT, press A.DUB also.

(“o” and “u” blink and “i” lights up on the front display panel.)

NOTES:

●All necessary cables can be obtained from your dealer.

●Insert Editing is not possible with cassettes whose record safety tab has been removed.

●When Insert Editing is performed on a tape that has been recorded on another video recorder, the inserted portion may appear distorted.

●In Insert Editing, the recording speed (SP/LP) is determined by the previous recording to be replaced. If the previous recording’s speed changes within a single edit, the inserted picture will be distorted at the switching point.

●A small portion of the recording which precedes an insert edit may become erased.

●Insert Editing is also possible using the rear panel AV1 (L-1) IN/ OUT or AV2 (L-2) IN/DECODER connector. When using these 21-pin SCART connectors, be sure to select the correct input mode (“L-1” or “L-2”) in step 2.

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display Remote Control Remote Control LCD How To UseConnect the recorder to TV Check the contents10 EN Situate the recorderVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectorsPlug the end of the mains power cord into a mains outlet Select your country Auto Set Up12 EN Turn on the recorderPress rt to select Auto and press OK or e Perform Auto Set UpSelect the language Press rt to select your language codePress rt to select CH - and press OK or e Perform Preset Download14 EN Set the video channelJust Clock Language for the on-screen display16 EN Access the Main Menu screenAccess the Country Set screen LanguageMake connections Installing Satellite ControllerSituate the Satellite Controller Attach the Satellite Controller18 EN Setting satellite receivers brand and channelVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link 20 EN Basic PlaybackActivate frame-by-frame playback Slow MotionHigh-Speed Turbo Search Pause during playbackIndex Search 22 ENVariable Speed Search Skip SearchSoundtrack Selection Next Function MemoryRepeat Playback Manual Tracking24 EN Tape Remaining Time Instant Timer Recording ITRLocate the start point Engage the Record-Pause mode26 EN RetakeAudio Recording Level Control Engage the S-VHS ET modeAdjust the audio recording level Super VHS ET S-VHS ETReceived Receiving Stereo and Bilingual ProgrammesOn-screen Display Recording Playback30 EN Access the Showview displayAccess the Showview screen Access the Showview Program screenEnter the programme title Set the VPS/PDC modeAccess the Title Edit screen Engage the recorder’s timer mode32 EN Express Timer ProgrammingPress PR+ To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the channel positionSet the programme start/stop time and channel Enter the programme modeBefore performing the 24 Hour Express Timer Programming 34 ENYou can programme this recorder to timer-record as many as Press # TIMER, then press Disengage the timer modeAccess the Programme Check screen/display Access the Programme screen/displayProgramme 4 overlap each other Cancel or change a programmeReturn to the timer mode Select the programme to modify Enter the programme title38 EN Select the L-2 Select modeRecording mode Programme RecordingChange the code for the recorder Remote A/B Code SwitchingSet the remote control code Check the remote control code for the recorderOperate the TV TV Multi-Brand Remote Control40 EN Set the TV brand codeOperate the satellite receiver Satellite Receiver Multi-Brand Remote ControlSet the satellite receiver brand code Check Memory Navigation42 EN Navigation PlaybackTurn off Navigation Turn Off NavigationVideo Navigation Title Screen Check the memoryFind Blank Space Access the Find Blank Space screenEdit Title 44 ENSelect the tape title Access the Edit Title screenEdit Tape Title Entering CharacterSelect the category 46 ENChoice of Category Select the programmeDelete the programme data Delete Tape DataDelete Programme Data Delete the tape dataSort By Tape Number Access the Find Title screenFind Title 48 ENSelect the programme Access the Tape No. screenAccess the Date screen Sort By DateCategory you want to watch Access the Category screen50 EN Sort By CategoryStart the camcorder Set the recorder’s input modeSet the edit mode Edit From a CamcorderPress OK or e Access the Output/Input Set screenOUTPUT/INPUT SET, then Decoder connector Select and L-2 Input Setting54 EN Another Video RecorderRecorder Player CD player, etc Audio Dubbing56 EN Pre-recorded tape Audio-dubbed tapePress AUX number key 0 and/or PR to select F-1 or S-1 Engage the Audio Dubbing modeStart dubbing End Audio DubbingAfter Insert Editing Insert Editing58 EN Source tape Before Insert Editing Recording tapeStart Editing Engage the Insert Editing modeAV Insert Editing Locate the end pointStart playback of the source cassette Access the R.A.Edit screen60 EN Load the source cassetteEnd Random Assemble Editing Memory CapacityPrepare the recording deck Start Random Assemble EditingPress Synchro 7/79 62 ENStart Synchro Editing Pause Synchro EditingExamples Access the Jlip ID No. Set screenSet the Jlip ID number Jlip ID NumberSimple Connections Connecting To a Satellite ReceiverSatellite receiver Decoder Back of recorder Perfect ConnectionsSet the tuner Select the input mode66 EN Connect the decoderMake connections Connecting/Using a Stereo SystemSelect the mode setting Mode SetAccess the Mode Set screen Select the modeOff, and automatically disengaged when the recorder is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture When this function is set to ON, the timer isFor Example 70 ENAbout Ntsc Playback Auto Channel Set Access the Auto Channel Set screenTuner Set 72 ENPress OK twice Perform Auto Channel SetView the Confirmation screen Manual Channel Set 74 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations B 76 ENSet Stations a Station Name TV Station And ID List78 EN Access the Video Channel Set modeExit the Video Channel Set mode Video Channel SetEnter the Guide Program number Showview System SetupGuide Program Number Set Guide Program Number80 EN Access the Clock Set screenClock Set Start the clock operation Set the date and timeSet Just Clock Set the source channel position for clock data82 EN TroubleshootingRecording 84 EN Timer RecordingPlayback 86 EN AV Insert Editing S.T. Picture System Auto Set UpManual Tracking Mode Set Audio DubbingCountry code International telephone Language code
Top Page Image Contents