JVC HR-S9850EU Perform Auto Channel Set, View the Confirmation screen, Press OK twice

Page 73

EN 73

IMPORTANT

●In certain reception conditions, station names may not be stored correctly, and Auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the SHOWVIEW system, the recorder will record a TV programme of a different station. When programming the

timer using the SHOWVIEW system, be sure to check the desired channel is selected correctly ( pg. 30, “SHOWVIEW® Timer Programming”).

●Your video recorder memorizes all detected stations even if

reception of some of them is poor. You can delete those stations with an unacceptable picture ( pg. 75, “Delete A Channel”).

NOTES:

●Fine tuning is performed automatically during Auto Channel Set. If you want to perform tuning manually, refer to page 76.

●If you perform Auto Channel Set when the aerial cable is not connected properly, “SCAN COMPLETED –NO SIGNAL–” appears on the TV screen in step 7. When this happens, make sure of the aerial connection and press OK; Auto Channel Set will take place again.

●If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect.

Select the appropriate TV system for those channels ( pg. 75, “INFORMATION”).

F Perform Auto Channel Set.

Press OK twice.

● If you have connected the

 

 

recorder and your TV via AV

 

 

connection ( pg. 10), the

 

 

recorder automatically

 

 

performs the Preset

 

 

Download and the T-V LINK

 

 

screen will appear

 

 

( pg. 14).

 

 

● The Auto Set screen appears,

Beginning

End

and remains on screen while

the recorder searches for receivable stations.

As Auto Channel Set progresses, the “q” mark on the TV screen moves from left to right. Wait until the TV screen as shown in step 7 appears.

G View the Confirmation screen.

After “SCAN COMPLETED” is displayed on the TV screen for about 5 seconds, the Confirmation screen looking like the one to the right appears. The stations your recorder located appear on a Confirmation screen —

channel positions (PR),

channels (CH) and station names (ID –  pg. 77). The blueback screen and the programme currently being broadcast by the blinking station appear alternately for 8 seconds each. To view the next page, use the rt w e button on the remote control.

●The stations located in the selected country appear at the top of the list.

●The Guide Program numbers will also be set automatically during Auto Channel Set.

H Return to the normal screen.

Press MENU.

●Using the Confirmation screen, you can skip or add channel positions, enter station names and perform other operations. Refer to pages 74 – 76 for the procedures.

●Depending on reception conditions, the stations may not be stored in order, and the station names may not be stored correctly.

●For information on scrambled broadcasts, refer to page 75.

Page 72 Page 74
Image 73
Page 72 Page 74
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display Remote Control Remote Control LCD How To Use10 EN Check the contentsSituate the recorder Connect the recorder to TVPlug the end of the mains power cord into a mains outlet 8To connect to a TV with S-VIDEO/AUDIO in connectorsVideo Connection 12 EN Auto Set UpTurn on the recorder Select your countrySelect the language Perform Auto Set UpPress rt to select your language code Press rt to select Auto and press OK or e14 EN Perform Preset DownloadSet the video channel Press rt to select CH - and press OK or eJust Clock Language for the on-screen displayAccess the Country Set screen Access the Main Menu screenLanguage 16 ENSituate the Satellite Controller Installing Satellite ControllerAttach the Satellite Controller Make connections18 EN Setting satellite receivers brand and channelNexTView Link TV Auto Power OnVCR Auto Standby Direct Rec 20 EN Basic PlaybackHigh-Speed Turbo Search Slow MotionPause during playback Activate frame-by-frame playbackVariable Speed Search 22 ENSkip Search Index SearchRepeat Playback Next Function MemoryManual Tracking Soundtrack Selection24 EN Tape Remaining Time Instant Timer Recording ITR26 EN Engage the Record-Pause modeRetake Locate the start pointAdjust the audio recording level Engage the S-VHS ET modeSuper VHS ET S-VHS ET Audio Recording Level ControlOn-screen Display Receiving Stereo and Bilingual ProgrammesReceived Recording PlaybackAccess the Showview screen Access the Showview displayAccess the Showview Program screen 30 ENAccess the Title Edit screen Set the VPS/PDC modeEngage the recorder’s timer mode Enter the programme title32 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+Before performing the 24 Hour Express Timer Programming Enter the programme mode34 EN Set the programme start/stop time and channelYou can programme this recorder to timer-record as many as Access the Programme Check screen/display Disengage the timer modeAccess the Programme screen/display Press # TIMER, then pressReturn to the timer mode Cancel or change a programmeSelect the programme to modify Enter the programme title Programme 4 overlap each otherRecording mode Select the L-2 Select modeProgramme Recording 38 ENSet the remote control code Remote A/B Code SwitchingCheck the remote control code for the recorder Change the code for the recorder40 EN TV Multi-Brand Remote ControlSet the TV brand code Operate the TVSet the satellite receiver brand code Satellite Receiver Multi-Brand Remote ControlOperate the satellite receiver 42 EN NavigationNavigation Playback Check MemoryVideo Navigation Title Screen Turn Off NavigationCheck the memory Turn off NavigationEdit Title Access the Find Blank Space screen44 EN Find Blank SpaceEdit Tape Title Access the Edit Title screenEntering Character Select the tape titleChoice of Category 46 ENSelect the programme Select the categoryDelete Programme Data Delete Tape DataDelete the tape data Delete the programme dataFind Title Access the Find Title screen48 EN Sort By Tape NumberAccess the Date screen Access the Tape No. screenSort By Date Select the programme50 EN Access the Category screenSort By Category Category you want to watchSet the edit mode Set the recorder’s input modeEdit From a Camcorder Start the camcorderOUTPUT/INPUT SET, then Access the Output/Input Set screenPress OK or e Decoder connector Select and L-2 Input Setting54 EN Another Video RecorderRecorder Player 56 EN Audio DubbingPre-recorded tape Audio-dubbed tape CD player, etcStart dubbing Engage the Audio Dubbing modeEnd Audio Dubbing Press AUX number key 0 and/or PR to select F-1 or S-158 EN Insert EditingSource tape Before Insert Editing Recording tape After Insert EditingAV Insert Editing Engage the Insert Editing modeLocate the end point Start Editing60 EN Access the R.A.Edit screenLoad the source cassette Start playback of the source cassettePrepare the recording deck Memory CapacityStart Random Assemble Editing End Random Assemble EditingStart Synchro Editing 62 ENPause Synchro Editing Press Synchro 7/79Set the Jlip ID number Access the Jlip ID No. Set screenJlip ID Number ExamplesSimple Connections Connecting To a Satellite ReceiverSatellite receiver Decoder Back of recorder Perfect Connections66 EN Select the input modeConnect the decoder Set the tunerMake connections Connecting/Using a Stereo SystemAccess the Mode Set screen Mode SetSelect the mode Select the mode settingThis feature helps you to adjust the playback picture You can set the B.E.S.T. Biconditional Equalised SignalWhen this function is set to ON, the timer is Off, and automatically disengaged when the recorder is For Example 70 ENAbout Ntsc Playback Tuner Set Access the Auto Channel Set screen72 EN Auto Channel SetView the Confirmation screen Perform Auto Channel SetPress OK twice Manual Channel Set 74 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations a 76 ENSet Stations B Station Name TV Station And ID ListExit the Video Channel Set mode Access the Video Channel Set modeVideo Channel Set 78 ENGuide Program Number Set Showview System SetupGuide Program Number Enter the Guide Program numberClock Set Access the Clock Set screen80 EN Set Just Clock Set the date and timeSet the source channel position for clock data Start the clock operation82 EN TroubleshootingRecording 84 EN Timer RecordingPlayback 86 EN Manual Tracking Mode Set Auto Set UpAudio Dubbing AV Insert Editing S.T. Picture SystemCountry code International telephone Language code
Top Page Image Contents