JVC HR-S9850EU specifications About Ntsc Playback

		EN 71
		* The default setting is bold in the table below.
8 VIDEO STABILIZER		When this function is set to “ON”, you can automatically correct vertical
ON		vibration in the picture when playing back unstable recordings made on
OFF		another recorder.
		NOTES:
		● When you finish viewing a tape, be sure to set this function to “OFF”.
		● Regardless of the setting, this function has no effect during recording and during special
		effects playback.
		● The on-screen display may jitter vertically when this function is set to “ON”.
		● To watch recordings with close-caption, set this function to “OFF”.
		● Video Stabilizer and Digital TBC/NR cannot be used at the same time. If you activate
		Digital TBC/NR when “VIDEO STABILIZER” is set to “ON”, Video Stabilizer will be
		automatically turned “OFF”.
8 S-VHS		Your recorder can record in S-VHS (Super VHS), S-VHS ET or VHS.
ON		●To record in S-VHS:
OFF
		Set “S-VHS” to “ON”. Then, insert a cassette marked “S-VHS”. The S-VHS
		indicator lights up on the front display panel.
		The S-VHS recording mode is selected.
		●To record in S-VHS ET on a VHS cassette:
		See “Super VHS ET (S-VHS ET)” on page 27.
		●To record in VHS:
		Insert a cassette marked “VHS”.
		If the S-VHS ET indicator on the recorder’s front panel is lit and the S-VHS ET
		mode is activated, press S-VHS ET. The S-VHS ET indicator goes off.
		The VHS recording mode is automatically selected regardless of the “S-VHS”
		mode setting.
		●To record in VHS on an S-VHS cassette:
		Insert a cassette marked “S-VHS”. The S-VHS indicator lights up on the front
		display panel. Then, set “S-VHS” to “OFF”. The S-VHS indicator goes off.
		The VHS recording mode is selected.
		NOTE:
		When playing back a tape that has been recorded in S-VHS or S-VHS ET, the S-VHS
		indicator lights up on the front display panel regardless of the “S-VHS” mode setting.
8 COLOUR SYSTEM		You can play back PAL, NTSC and MESECAM tapes, or record PAL and SECAM*
PAL/NTSC:	To record PAL	signals on this recorder. Select the appropriate colour system.
	signals, or play	* SECAM signals will be recorded as MESECAM on this recorder; MESECAM is the
	back a PAL or	designation for tapes with SECAM signals that have been recorded on a
	NTSC tape.	MESECAM-compatible PAL video cassette recorder.
MESECAM:		NOTES:
	To record
	SECAM signals,	● It is not possible to record in S-VHS if “MESECAM” is selected. The recording mode is
	or play back a
		forced to change to VHS.
	MESECAM tape.
		● If “MESECAM” is selected when the tape speed is set to EP mode, the tape speed will be
		forced to change to LP mode.
		● It is not possible to select EP mode if “MESECAM” is selected.
		About NTSC Playback
		● Some TVs shrink the picture vertically and place black bars at the top and bottom of the
		TV screen. This is not a malfunction on the part of either the video recorder or the TV.
		● The picture may roll up and down. This can be corrected using the V-HOLD control
		found on some TVs. (This cannot be corrected if the TV does not have a V-HOLD
		control.)
		● The counter and tape remaining time readings will be incorrect.
		● During search, still, or frame-by-frame playback, the picture will be distorted, and there
		may be a loss of colour.
		● Depending on the type of TV, the top and bottom portions of superimposed displays
		may be cut off during NTSC playback.