JVC HR-S9850EU specifications Recording

Page 83

 

 

 

EN 83

RECORDING

 

 

 

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1.

Recording cannot be started.

● There is no cassette loaded, or the

Insert a cassette, or using adhesive tape,

 

 

cassette loaded has had its record safety

cover the hole where the tab was

 

 

tab removed.

removed.

 

 

 

 

2.

TV broadcasts cannot be recorded.

● “L-1”, “L-2”, “F-1”, “S-1” or “SAT” has

Set to the desired channel.

 

 

been selected as the input mode.

 

 

 

 

 

3.

Tape-to-tape editing is not possible.

● The source (another video recorder,

Confirm that the source is properly

 

 

camcorder) has not been properly

connected.

 

 

connected.

 

 

 

● All necessary power switches have not

Confirm that all units’ power switches are

 

 

been turned on.

turned on.

 

 

● The input mode is not correct.

Set the input mode to “L-1”, “L-2”, “F-1”

 

 

 

or “S-1”.

 

 

 

 

4.

Camcorder recording is not possible.

● The camcorder has not been properly

Confirm that the camcorder is properly

 

 

connected.

connected.

 

 

● The input mode is not correct.

Set the input mode to “L-1”, “L-2”, “F-1”

 

 

 

or “S-1”.

 

 

 

 

5.

“[” on the front display panel won’t

● The end of the tape was reached during

The programme may not have been

 

stop blinking.

recording.

recorded in its entirety. Next time make

 

 

 

sure you have enough time on the tape to

 

 

 

record the entire programme.

 

 

 

TIMER RECORDING

 

 

 

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1.

Timer recording won’t work.

● The clock and/or the timer have been set

Re-perform the clock and/or timer

 

 

incorrectly.

settings.

 

 

● The timer is not engaged.

Press # and confirm that “#” is displayed

 

 

 

on the front display panel.

 

 

 

 

2.

Timer programming is not possible.

● Timer recording is in progress.

Timer programming can’t be performed

 

 

 

while a timer recording is in progress.

 

 

 

Wait until it finishes.

 

 

 

 

3.

“#” and “[” on the front display

● The timer is engaged but there’s no

Load a cassette with the record safety tab

 

panel won’t stop blinking.

cassette loaded.

intact, or cover the hole using adhesive

 

 

 

tape.

 

 

● The loaded cassette has had its record

Remove the cassette and cover the hole

 

 

safety tab removed.

with adhesive tape, or insert a cassette

 

 

 

with the record safety tab intact.

 

 

● The end of the tape was reached during

The programme may not have been

 

 

timer recording.

recorded in its entirety. Next time make

 

 

 

sure you have enough time on the tape to

 

 

 

record the entire programme.

 

 

 

 

4.

“#” blinks for 10 seconds and the

● # has been pressed when there are no

Check the programmed data and

 

Timer mode is disengaged.

programs in memory, or the timer

re-program as necessary, then press #

 

 

record information has been

again.

 

 

programmed incorrectly.

 

 

 

 

 

5.

The SHOWVIEW system does not

● The recorder’s channel positions have

Refer to “Guide Program Number Set”

 

timer-record properly.

been set incorrectly.

( pg. 79) and re-perform the procedure.

 

 

 

 

Page 82 Page 84
Image 83
Page 82 Page 84
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display Remote Control Remote Control LCD How To UseConnect the recorder to TV Check the contents10 EN Situate the recorderVideo Connection 8To connect to a TV with S-VIDEO/AUDIO in connectorsPlug the end of the mains power cord into a mains outlet Select your country Auto Set Up12 EN Turn on the recorderPress rt to select Auto and press OK or e Perform Auto Set UpSelect the language Press rt to select your language codePress rt to select CH - and press OK or e Perform Preset Download14 EN Set the video channelJust Clock Language for the on-screen display16 EN Access the Main Menu screenAccess the Country Set screen LanguageMake connections Installing Satellite ControllerSituate the Satellite Controller Attach the Satellite Controller18 EN Setting satellite receivers brand and channelVCR Auto Standby Direct Rec TV Auto Power OnNexTView Link 20 EN Basic PlaybackActivate frame-by-frame playback Slow MotionHigh-Speed Turbo Search Pause during playbackIndex Search 22 ENVariable Speed Search Skip SearchSoundtrack Selection Next Function MemoryRepeat Playback Manual Tracking24 EN Tape Remaining Time Instant Timer Recording ITRLocate the start point Engage the Record-Pause mode26 EN RetakeAudio Recording Level Control Engage the S-VHS ET modeAdjust the audio recording level Super VHS ET S-VHS ETReceived Receiving Stereo and Bilingual ProgrammesOn-screen Display Recording Playback30 EN Access the Showview displayAccess the Showview screen Access the Showview Program screenEnter the programme title Set the VPS/PDC modeAccess the Title Edit screen Engage the recorder’s timer mode32 EN Express Timer ProgrammingPress PR+ To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Enter the channel positionSet the programme start/stop time and channel Enter the programme modeBefore performing the 24 Hour Express Timer Programming 34 ENYou can programme this recorder to timer-record as many as Press # TIMER, then press Disengage the timer modeAccess the Programme Check screen/display Access the Programme screen/displayProgramme 4 overlap each other Cancel or change a programmeReturn to the timer mode Select the programme to modify Enter the programme title38 EN Select the L-2 Select modeRecording mode Programme RecordingChange the code for the recorder Remote A/B Code SwitchingSet the remote control code Check the remote control code for the recorderOperate the TV TV Multi-Brand Remote Control40 EN Set the TV brand codeOperate the satellite receiver Satellite Receiver Multi-Brand Remote ControlSet the satellite receiver brand code Check Memory Navigation42 EN Navigation PlaybackTurn off Navigation Turn Off NavigationVideo Navigation Title Screen Check the memoryFind Blank Space Access the Find Blank Space screenEdit Title 44 ENSelect the tape title Access the Edit Title screenEdit Tape Title Entering CharacterSelect the category 46 ENChoice of Category Select the programmeDelete the programme data Delete Tape DataDelete Programme Data Delete the tape dataSort By Tape Number Access the Find Title screenFind Title 48 ENSelect the programme Access the Tape No. screenAccess the Date screen Sort By DateCategory you want to watch Access the Category screen50 EN Sort By CategoryStart the camcorder Set the recorder’s input modeSet the edit mode Edit From a CamcorderPress OK or e Access the Output/Input Set screenOUTPUT/INPUT SET, then Decoder connector Select and L-2 Input Setting54 EN Another Video RecorderRecorder Player CD player, etc Audio Dubbing56 EN Pre-recorded tape Audio-dubbed tapePress AUX number key 0 and/or PR to select F-1 or S-1 Engage the Audio Dubbing modeStart dubbing End Audio DubbingAfter Insert Editing Insert Editing58 EN Source tape Before Insert Editing Recording tapeStart Editing Engage the Insert Editing modeAV Insert Editing Locate the end pointStart playback of the source cassette Access the R.A.Edit screen60 EN Load the source cassetteEnd Random Assemble Editing Memory CapacityPrepare the recording deck Start Random Assemble EditingPress Synchro 7/79 62 ENStart Synchro Editing Pause Synchro EditingExamples Access the Jlip ID No. Set screenSet the Jlip ID number Jlip ID NumberSimple Connections Connecting To a Satellite ReceiverSatellite receiver Decoder Back of recorder Perfect ConnectionsSet the tuner Select the input mode66 EN Connect the decoderMake connections Connecting/Using a Stereo SystemSelect the mode setting Mode SetAccess the Mode Set screen Select the modeOff, and automatically disengaged when the recorder is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture When this function is set to ON, the timer isFor Example 70 ENAbout Ntsc Playback Auto Channel Set Access the Auto Channel Set screenTuner Set 72 ENPress OK twice Perform Auto Channel SetView the Confirmation screen Manual Channel Set 74 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations B 76 ENSet Stations a Station Name TV Station And ID List78 EN Access the Video Channel Set modeExit the Video Channel Set mode Video Channel SetEnter the Guide Program number Showview System SetupGuide Program Number Set Guide Program Number80 EN Access the Clock Set screenClock Set Start the clock operation Set the date and timeSet Just Clock Set the source channel position for clock data82 EN TroubleshootingRecording 84 EN Timer RecordingPlayback 86 EN AV Insert Editing S.T. Picture System Auto Set UpManual Tracking Mode Set Audio DubbingCountry code International telephone Language code
Top Page Image Contents