JVC HR-J278EU specifications Perform Auto Channel Set, View the Confirmation screen, Press OK

Page 31

EN 31

IMPORTANT

Your video recorder memorizes all detected stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture ( pg. 32, “Delete A Channel”).

NOTES:

Fine tuning is performed automatically during Auto Channel Set. If you want to perform it manually, refer to page 33.

If you perform Auto Channel Set when the aerial cable is not connected properly, “SCAN COMPLETED -NO SIGNAL-” appears on the TV screen in step 7. When this happens, make sure of the aerial connection and press OK; Auto Channel Set will take place again.

If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect.

Select the appropriate TV system for those channels ( pg. 32, “INFORMATION”).

F Perform Auto Channel Set.

Press OK.

The Auto Set screen appears,

and remains on screen while

 

 

the recorder searches for

 

 

receivable stations.

 

 

As Auto Channel Set

 

 

progresses, the “q” mark on

 

 

the TV screen moves from

 

 

left to right. Wait until the TV

 

 

screen as shown in step 7

Beginning

End

appears.

 

 

G View the Confirmation screen.

After “SCAN COMPLETED” is displayed on the TV screen for about 5 seconds, the Confirmation screen looking like the one to the right appears. The stations your

recorder located appear on a Confirmation screen — channel positions (PR) and

frequency (FRQ). The blueback screen and the programme currently being broadcast by the blinking station appear alternately for 8 seconds each. To view the next page, use the rt button on the remote control.

The stations located in the selected country appear at the top of the list.

If you have selected MAGYARORSZÁG, CESKÁ REPUBLIKA,

POLSKA or OTHER EASTERN EUROPE for the country setting ( pg. 8, 11), refer to “INFORMATION” on page 32.

H Return to the normal screen.

Press MENU.

Using the Confirmation screen, you can delete channels, swap channel positions and fine-tune channels already stored. Refer to pages 32 – 33 for the procedures.

Image 31
Contents Video Cassette Recorder English Safety Precautions Moisture Condensation Front View Front Display Panel ON-SCREEN Display Operating JVC TVs How To UseConnect the recorder to mains Check the contentsSituate the recorder Connect the recorder to TVBefore starting, make sure of the following Auto Set UpTurn on the recorder Select your countryPress OK. The Language Set display appears on the TV screen Perform Auto Set UpSelect the language Set the date and timeLanguage for the on-screen display 10 ENReturn to the normal screen Access the Main Menu screenAccess the Country Set screen Language12 EN Basic PlaybackPause during playback Slow MotionHigh-Speed Search Variable Speed SearchManual Tracking 14 ENInstant ReView Repeat Playback Index SearchSkip Search Next Function Memory16 EN Set the recording duration Instant Timer Recording ITREngage the ITR mode Watching AnotherPress -- so that a counter reading appears on the TV screen Reset the counter18 EN Tape Remaining TimeRecording Playback20 EN Express Timer ProgrammingPress PR + Engage the recorder’s timer modeTo Timer-Record Weekly Or Daily Serials Enter the channel positionDisengage the timer mode Check, cancel and change programmesCancel or change a programme Return to the timer modeConfirm the overlapping programmes Cancel or change programme settingSelect the programme to modify 24 EN Edit From a CamcorderStart the recording deck Set the input mode of recording deckAnother Video Recorder Start the source playerSelect the mode setting Mode SetAccess the Mode Set screen Select the modeOff, and automatically disengaged when the recorder is You can set the B.E.S.T. Biconditional Equalised SignalThis feature helps you to adjust the playback picture When this function is set to ON, the timer isAbout Ntsc Playback 28 ENClock Set Access the Clock Set screenStart the clock operation Auto Channel Set Access the Auto Channel Set screenTuner Set 30 ENView the Confirmation screen Perform Auto Channel SetPress OK Delete a Channel 32 ENSelect the channel to fine-tune Perform tuningSwap Channel Positions Select the position. e.g34 EN Video Channel SetPower Recording 36 ENOther Problems Playback 38 ENDelete a Channel Auto Channel Set Auto Set UpAnother Horizontal resolution 250 lines Power requirement AC 220 V 240 VdSignal system Monochrome signal, 625 lines
Related manuals
Manual 40 pages 7.52 Kb