JVC Model SR-TS1U manual Cable Box Control, Situate Controller, Attach Controller

Page 15

EN15

Cable Box

Control

Suggested Location

Place the cable box on top of the VCR. Attach the VCR's Controller to the top of the VCR with the Controller’s transmitter pointed towards the cable box’s remote sensor.

ATTENTION:

The Controller can also control a DBS receiver. If both a cable box and a DBS receiver are used, position the controller so its signal reaches the remote control sensors of both the cable box and DBS receiver.

Cable box

Controller

Your VCR(suggested

locations)

Cable box

Controller

Transmitter

Connected to

ANTENNA IN

Your VCR

CABLE

BOX

This procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the VCR to automatically switch the cable box channel during timer-recording. The Controller is effective for recording shows that have been programmed using VCR Plus+ ( pg. 43) or Express Timer Programming ( pg. 47).

Situate And Connect

Controller

SITUATE CONTROLLER

1 Place the Controller so that the path between its transmitter and the cable box’s remote sensor is unobstructed.

ATTACH CONTROLLER

2 Fasten securely using the supplied adhesive strip.

CONNECT CABLE BOX TO VCR

3 The connection method depends on the type of cable box you have.

If your cable box has AUDIO and VIDEO OUT connectors . . .

. . . connect them to the AUDIO and VIDEO IN connectors on your VCR. Set the VCR to channel "L-1" for the rear AUDIO and VIDEO IN connectors, or channel "F-1" for the front AUDIO and VIDEO IN connectors to use the cable box.

If your cable box doesn’t have AUDIO and VIDEO OUT connectors . . .

. . . connect the antenna output connector on the cable box to the ANTENNA IN connector on the rear of your VCR.

Set the VCR tuner to the same channel as the cable box RF output (see page 16 also).

NOTE:

When connecting your cable box refer to its instruction manual.

CONNECT CONTROLLER TO VCR

4 Connect to the CABLE BOX connector on your VCR.

About Your Cable Box

This VCR has two separate methods to control your Cable Box.

The VCR's Wireless Remote Control Unit can control your Cable Box.

This eliminates the need for a separate Cable Box Remote Control Unit.

The VCR's Controller can also control your Cable Box.

This allows the VCR to change your Cable Box's channel number during timer recording.

Each method must be set up separately. To set up the VCR's Remote Control unit, refer to page 57. To set up the Controller go to page 16.

Page 14 Page 16
Image 15
Page 14 Page 16
Contents SR-TS1U Dear Customer Grounding or Polarization Power SourcesPower Cord Protection Power LinesReplacement Parts AccessoriesDamage Requiring Service CleaningContents Connections Installing/Removing the lithium battery Back of VCRConnect VCR to TV Auto Clock Set/Auto Tuner Set Plug & Play SetupPlug & Play EN I Nitial Sett IngsInformation Clock Semi-Auto Select D.S.T. ModeSET Auto Clock to on Select Host ChannelSET Date Select Time ZoneReturn to Normal Screen SET TimeSet Receivable Channels Access Main Menu ScreenTuner SETOr Shuttle Plus # Access ManualChannel Add Or Delete a ChannelConnect Cable BOX to VCR Cable Box ControlSituate Controller Attach ControllerSet Cable Box Output Channel & Cable Box Brand Access Cable BOX SET ScreenTurn on Cable BOX Select Cable BOX Output ChannelAccess Cable BOX Brand SET Screen Enter Cable BOX BrandBrand Code DBS Receiver Control Connect DBS Receiver to VCRDBS receiver Output Channel Access DBS Receiver SETTurn on DBS Receiver Select DBS ReceiverJVC Dish Network Echostar Dish Network Access DBS ReceiverSET DBS Receiver Brand DBS Receiver Code from Following list, then Press OKStart Playback Simple PlaybackLoad a Cassette Find Program Start PointSimple Recording Playback and Recording FEA Tures E N Playback FeaturesActivate FRAME-BY Frame PlaybackActivate HIGH-SPEED Search Access Distant CodeEngage Manual Tracking Mode Adjust Manual TrackingSET Mode Picture ControlSelect Picture Control Select Audio Monitor Select The SoundtrackShuttle Plus #to select Video Stabilizer Activate Video StabilizerShuttle Plus # to set to Or Shuttle PLUS%Þ Instant ReViewReturning Position ReviewNext-Function Memory Counter ResetTape Position Indicator Repeat PlaybackTape speed indication Cassette Loaded mark Audio mode Counter reading IndicationsOperation mode SuperimposePress Skip Search Movie AdvanceSeries Playback To S Video OUT Video Cable SuppliedTo S Video OUT Video Cable Supplied To Remote To Audio Press Play on either of SR-TS1U Make ConnectionsTurn on ALL Components Load CassettesCamcorder Series RecordingSET Recording VCR’S Input Mode Turn on ALL ComponentsPrepare for Recording Video Calibration Active Video CalibrationPlayback RecordingStart Playback Recording Features Shuttle Plus # to select Record SafetySET Screen Or Shuttle PlusAccess Function SET 1 Screen Select S-VHS ModeVHS Super VHS, S-VHS ET and VHS Select S-VHS ET SET ModeSuper VHS ET Select 2ND Audio Record SET Mode Stereo And SAP Second Audio ProgramTo Record SAP Programs Enter Pluscode Number VCR Plus+ Timer ProgrammingTimer Recording Input Receiving Channel NumberProgram SP/EPVCR Plus+ Setup VCR Plus+ Guide Channel MatchingInitial SET, then press Input Guide Channel Number Access Guide Channel SET ScreenEN Timer Recording Ex. When inputting the Guide Channel number 6 for WNJUIndSET Channel Number Express Timer ProgrammingAccess VCR PLUS+ SET Program DateEngage Timer Mode Program Cancel or Revise aRE-ENGAGE Timer Check, Cancel And Revise ProgramsSelect Auto SP EP Timer SET Mode Auto SP→EP TimerAuto Timer Press REC on the front panel Instant Timer Recording ITREngage ITR Mode SET Recording DurationEngage Auto Satellite Prog REC Mode Automatic Sat- ellite Program RecordingBefore performing the following steps Start Player Edit To Or From AnotherSET RECORDER’S Input Select Edit for PICPlayer Edit From a CamcorderSelect Rear AUX Input SET Mode Set the camcorder to its play modeSet your VCR to its record mode Operate TV TV Multi-Brand Remote ControlTurn on the TV SET TV Brand CodeCable BOX Brand Name Brand Code Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Operate Cable BOXEnter DBS Receiver Brand EN Special FeaturesDBS Receiver Multi-Brand Remote Control Turn on the DBS ReceiverTurn VCR Power on Unplug Vcrs PowerSET Remote Control Plug in Power CordMake sure the cassettes window is Cassette gets stuck partwayTimer again Re-perform the VCR Plus+ setup Doesn’t work properlyProcedure Those in the previous area Other Problems TroubleshootingWhat happens if the tape runs out during recording? Questions and Answer S E NCan the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?List Of Terms EN IndexFront View Front Display Panel IndexRemote Control Failure to heed the following precautions may result Damage to the VCR, remote control or videoCassette Memo Memo Memo SR-TS1U
Top Page Image Contents