JVC Model SR-TS1U SET Recording VCR’S Input Mode, Turn on ALL Components, Prepare for Recording

Page 35

JOG

SHATTLE

REC

STOP/EJECT

EN35

START RECORDING

5 Press REC on either of SR-TS1U.

When the tape reaches to the end while recording, the other SR-TS1U successively starts to record. Therefore, recording will be continued onto cassettes loaded on two SR-TS1U alternately.

The cassette will automatically be rewound when the recording stops.

Replace the cassette after rewound if you want to continue to record onto another cassette.

STOP PLAYBACK

6 Press STOP/EJECT on the SR-TS1U which is recording.

Using two sets of SR-TS1U, a long recording will be possible (such as camcorder recording, another VCR playback or TV broadcast).

Use the buttons and controls on the VCR‘s front display panel for the Series Playback operations (except when using Mode Lock).

1

MAKE CONNECTIONS

Connect two sets of SR-TS1U to other equipment, an-

tenna or cable as shown in the illustration on page 34.

 

The mini-plug cable is a mono 3.5 mm mini-plug to

 

mono 3.5 mm mini-plug connector.

 

When connecting a camcorder or another VCR with

 

an S-VIDEO output connector as recording source, it

 

is recommended to use the S-VIDEO connection to

 

minimize picture degradation.

2

TURN ON ALL COMPONENTS

After completing the connections, turn on all the

components.

 

Set the TV to video input mode or A/V input mode.

 

Refer to the TV instruction manual.

SET RECORDING VCR’S

INPUT MODE

3 Set to "AUX". Press CH 5° to select the input mode depending on the connector being used – "L-1" for the rear AUDIO/VIDEO IN connector, or "F-1" for the front AUDIO/VIDEO IN connector.

4

PREPARE FOR RECORDING

Insert the recording cassette into each SR-TS1U, and

prepare the playback source.

NOTE:

 

If you do not want to display the superimposed

 

indication on the screen during recording, set it to

 

"OFF" ( pg. 30). If the playback equipment has a

 

superimpose/OSD disable feature, set its superimpose

 

or display feature to "OFF" as well.

To prohibit operations during Series Recording (Mode Lock)

Press and hold OK on the remote control for more than 5 seconds. The Mode Lock indicator lights up on the front display panel ( pg. 66). The picture will be recorded onto the cassettes alternately without any interruption.

To resume the other operations, press and hold OK on the remote control again for more than 5 seconds.

NOTES:

Series Recording is also possible using the front AUDIO/ VIDEO connectors.

When recording a TV broadcast, tune in the same channel on both SR-TS1U.

If you do not want to record the superimposed operational indications on the screen during Series Recording, set the Superimpose mode both in playback and recording to "OFF". ( pg. 30)

Page 34 Page 36
Image 35
Page 34 Page 36
Contents SR-TS1U Dear Customer Grounding or Polarization Power SourcesPower Cord Protection Power LinesReplacement Parts AccessoriesDamage Requiring Service CleaningContents Connections Connect VCR to TV Installing/Removing the lithium batteryBack of VCR Auto Clock Set/Auto Tuner Set Plug & Play SetupPlug & Play EN I Nitial Sett IngsInformation Clock Semi-Auto Select D.S.T. ModeSET Auto Clock to on Select Host ChannelSET Date Select Time ZoneReturn to Normal Screen SET TimeSet Receivable Channels Access Main Menu ScreenTuner SETOr Shuttle Plus # Access ManualChannel Add Or Delete a ChannelConnect Cable BOX to VCR Cable Box ControlSituate Controller Attach ControllerSet Cable Box Output Channel & Cable Box Brand Access Cable BOX SET ScreenTurn on Cable BOX Select Cable BOX Output ChannelBrand Code Access Cable BOX Brand SET ScreenEnter Cable BOX Brand DBS receiver DBS Receiver ControlConnect DBS Receiver to VCR Output Channel Access DBS Receiver SETTurn on DBS Receiver Select DBS ReceiverJVC Dish Network Echostar Dish Network Access DBS ReceiverSET DBS Receiver Brand DBS Receiver Code from Following list, then Press OKStart Playback Simple PlaybackLoad a Cassette Find Program Start PointSimple Recording Playback and Recording FEA Tures E N Playback FeaturesActivate FRAME-BY Frame PlaybackActivate HIGH-SPEED Search Access Distant CodeEngage Manual Tracking Mode Adjust Manual TrackingSelect Picture Control SET ModePicture Control Shuttle Plus #to select Select Audio MonitorSelect The Soundtrack Shuttle Plus # to set to Video StabilizerActivate Video Stabilizer Or Shuttle PLUS%Þ Instant ReViewReturning Position ReviewNext-Function Memory Counter ResetTape Position Indicator Repeat PlaybackTape speed indication Cassette Loaded mark Audio mode Counter reading IndicationsOperation mode SuperimposePress Skip Search Movie AdvanceTo S Video OUT Video Cable Supplied To Remote To Audio Series PlaybackTo S Video OUT Video Cable Supplied Press Play on either of SR-TS1U Make ConnectionsTurn on ALL Components Load CassettesCamcorder Series RecordingPrepare for Recording SET Recording VCR’S Input ModeTurn on ALL Components Video Calibration Active Video CalibrationStart Playback PlaybackRecording Recording Features Shuttle Plus # to select Record SafetySET Screen Or Shuttle PlusVHS Super VHS, S-VHS ET and VHS Access Function SET 1 ScreenSelect S-VHS Mode Super VHS ET Select S-VHS ET SETMode To Record SAP Programs Select 2ND Audio Record SET ModeStereo And SAP Second Audio Program Enter Pluscode Number VCR Plus+ Timer ProgrammingTimer Recording Input Receiving Channel NumberProgram SP/EPInitial SET, then press VCR Plus+ SetupVCR Plus+ Guide Channel Matching Input Guide Channel Number Access Guide Channel SET ScreenEN Timer Recording Ex. When inputting the Guide Channel number 6 for WNJUIndSET Channel Number Express Timer ProgrammingAccess VCR PLUS+ SET Program DateEngage Timer Mode Program Cancel or Revise aRE-ENGAGE Timer Check, Cancel And Revise ProgramsAuto Timer Select Auto SP EP Timer SET ModeAuto SP→EP Timer Press REC on the front panel Instant Timer Recording ITREngage ITR Mode SET Recording DurationBefore performing the following steps Engage Auto Satellite Prog REC ModeAutomatic Sat- ellite Program Recording Start Player Edit To Or From AnotherSET RECORDER’S Input Select Edit for PICPlayer Edit From a CamcorderSet your VCR to its record mode Select Rear AUX Input SET ModeSet the camcorder to its play mode Operate TV TV Multi-Brand Remote ControlTurn on the TV SET TV Brand CodeCable BOX Brand Name Brand Code Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Operate Cable BOXEnter DBS Receiver Brand EN Special FeaturesDBS Receiver Multi-Brand Remote Control Turn on the DBS ReceiverTurn VCR Power on Unplug Vcrs PowerSET Remote Control Plug in Power CordMake sure the cassettes window is Cassette gets stuck partwayProcedure Those in the previous area Timer againRe-perform the VCR Plus+ setup Doesn’t work properly Other Problems TroubleshootingWhat happens if the tape runs out during recording? Questions and Answer S E NCan the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?List Of Terms EN IndexFront View Front Display Panel IndexRemote Control Cassette Failure to heed the following precautions may resultDamage to the VCR, remote control or video Memo Memo Memo SR-TS1U
Top Page Image Contents