JVC Model SR-TS1U manual DBS Receiver Control, Connect DBS Receiver to VCR, DBS receiver

Page 18

18ENINITIALSETTINGS(cont.)

DBS Receiver Control

Suggested Location

Place the DBS (Direct Broadcast Satellite) receiver on top of the VCR. Attach the VCR's Controller to the top of the VCR with the Controller’s transmitter pointed towards the DBS receiver's remote sensor.

ATTENTION:

The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the controller so its signal reaches the remote control sensors of both the DBS receiver and cable box.

The following procedure is required if you receive satellite channels through a DBS (Direct Broadcast Satellite) Receiver. The Controller allows the VCR to automatically switch the DBS Receiver's channels during timer recording.

NOTES:

The VCR can automatically change the DBS Receiver channels using the Controller when the VCR has been programmed using Express Timer Programming ( pg. 42).

Because satellite programming does not use PlusCode; the Controller cannot change the DBS Receiver channels during VCR Plus+ Timer Recording.

If a cable box is also used it is recommended that you connect the DBS receiver to your VCR's A/V inputs and the cable box to your VCR's antenna input.

Situate And Connect

Controller

DBS receiver

Your VCR

Controller

(suggested locations)

DBS receiver

 

Controller

 

Transmitter

 

 

Connected

Connected to

to VIDEO/

ANTENNA IN

AUDIO IN

Your VCR

CABLE

BOX

About Your DBS Receiver

This VCR has two separate methods to control your DBS Receiver.

The VCR's Wireless Remote Control Unit can control your DBS Receiver.

This eliminates the need for a separate DBS Receiver Remote Control Unit.

The VCR's Controller can also control your DBS Receiver. This allows the VCR to change your DBS receiver's channel number during timer recording.

Each method must be set up separately. To set up the VCR's Remote Control unit, refer to page 58. To set up the Controller go to page 19.

1

2

3

4

SITUATE CONTROLLER

Place the Controller so that the path between its transmitter and the DBS receiver's remote sensor is unobstructed.

ATTACH CONTROLLER

Fasten securely using the supplied adhesive strips.

CONNECT DBS RECEIVER TO VCR

The connection method depends on the type of DBS receiver you have.

If your DBS receiver has AUDIO and VIDEO OUT connectors . . .

. . . connect them to the AUDIO and VIDEO IN connectors on your VCR. Set the VCR to channel "L-1" for the rear AUDIO and VIDEO IN connectors, or channel "F-1" for the front AUDIO and VIDEO IN connectors to use the DBS receiver.

If your DBS receiver doesn’t have AUDIO and VIDEO OUT connectors . . .

. . . connect the antenna output connector on the DBS receiver to the ANTENNA IN connector on the rear of your VCR.

Set the VCR's tuner to the same channel as the DBS receiver's RF output. (See page 19 also.)

NOTE:

When connecting your DBS receiver refer to its instruction manual.

CONNECT CONTROLLER TO VCR

Connect to the CABLE BOX connector on your VCR.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents SR-TS1U Dear Customer Power Lines Power SourcesPower Cord Protection Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Connections Installing/Removing the lithium battery Back of VCRConnect VCR to TV EN I Nitial Sett Ings Plug & Play SetupPlug & Play Auto Clock Set/Auto Tuner SetInformation Clock Select Host Channel Select D.S.T. ModeSET Auto Clock to on Semi-AutoSET Time Select Time ZoneReturn to Normal Screen SET DateSET Access Main Menu ScreenTuner Set Receivable ChannelsAdd Or Delete a Channel Access ManualChannel Or Shuttle Plus #Attach Controller Cable Box ControlSituate Controller Connect Cable BOX to VCRSelect Cable BOX Output Channel Access Cable BOX SET ScreenTurn on Cable BOX Set Cable Box Output Channel & Cable Box BrandAccess Cable BOX Brand SET Screen Enter Cable BOX BrandBrand Code DBS Receiver Control Connect DBS Receiver to VCRDBS receiver Select DBS Receiver Access DBS Receiver SETTurn on DBS Receiver Output ChannelDBS Receiver Code from Following list, then Press OK Access DBS ReceiverSET DBS Receiver Brand JVC Dish Network Echostar Dish NetworkFind Program Start Point Simple PlaybackLoad a Cassette Start PlaybackSimple Recording Frame Playback Playback FeaturesActivate FRAME-BY Playback and Recording FEA Tures E NAdjust Manual Tracking Access Distant CodeEngage Manual Tracking Mode Activate HIGH-SPEED SearchSET Mode Picture ControlSelect Picture Control Select Audio Monitor Select The SoundtrackShuttle Plus #to select Video Stabilizer Activate Video StabilizerShuttle Plus # to set to Review Instant ReViewReturning Position Or Shuttle PLUS%ÞRepeat Playback Counter ResetTape Position Indicator Next-Function MemorySuperimpose Audio mode Counter reading IndicationsOperation mode Tape speed indication Cassette Loaded markMovie Advance Press Skip SearchSeries Playback To S Video OUT Video Cable SuppliedTo S Video OUT Video Cable Supplied To Remote To Audio Load Cassettes Make ConnectionsTurn on ALL Components Press Play on either of SR-TS1USeries Recording CamcorderSET Recording VCR’S Input Mode Turn on ALL ComponentsPrepare for Recording Active Video Calibration Video CalibrationPlayback RecordingStart Playback Recording Features Or Shuttle Plus Record SafetySET Screen Shuttle Plus # to selectAccess Function SET 1 Screen Select S-VHS ModeVHS Super VHS, S-VHS ET and VHS Select S-VHS ET SET ModeSuper VHS ET Select 2ND Audio Record SET Mode Stereo And SAP Second Audio ProgramTo Record SAP Programs Input Receiving Channel Number VCR Plus+ Timer ProgrammingTimer Recording Enter Pluscode NumberSP/EP ProgramVCR Plus+ Setup VCR Plus+ Guide Channel MatchingInitial SET, then press Ex. When inputting the Guide Channel number 6 for WNJUInd Access Guide Channel SET ScreenEN Timer Recording Input Guide Channel NumberSET Program Date Express Timer ProgrammingAccess VCR PLUS+ SET Channel NumberEngage Timer Mode Check, Cancel And Revise Programs Cancel or Revise aRE-ENGAGE Timer ProgramSelect Auto SP EP Timer SET Mode Auto SP→EP TimerAuto Timer SET Recording Duration Instant Timer Recording ITREngage ITR Mode Press REC on the front panelEngage Auto Satellite Prog REC Mode Automatic Sat- ellite Program RecordingBefore performing the following steps Select Edit for PIC Edit To Or From AnotherSET RECORDER’S Input Start PlayerEdit From a Camcorder PlayerSelect Rear AUX Input SET Mode Set the camcorder to its play modeSet your VCR to its record mode SET TV Brand Code TV Multi-Brand Remote ControlTurn on the TV Operate TVOperate Cable BOX Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Cable BOX Brand Name Brand CodeTurn on the DBS Receiver EN Special FeaturesDBS Receiver Multi-Brand Remote Control Enter DBS Receiver BrandPlug in Power Cord Unplug Vcrs PowerSET Remote Control Turn VCR Power onCassette gets stuck partway Make sure the cassettes window isTimer again Re-perform the VCR Plus+ setup Doesn’t work properlyProcedure Those in the previous area Troubleshooting Other ProblemsCan the VCR indefinitely remain in the Record-Pause mode? Questions and Answer S E NCan the VCR indefinitely remain in the still mode? What happens if the tape runs out during recording?EN Index List Of TermsFront View Index Front Display PanelRemote Control Failure to heed the following precautions may result Damage to the VCR, remote control or videoCassette Memo Memo Memo SR-TS1U
Top Page Image Contents