JVC Model SR-TS1U manual Turn on the TV, SET TV Brand Code, Operate TV, EN Special Feat Ures

Page 56

56ENSPECIALFEATURES

	BR
		SET
	TV
	TV/VCR
	1	ENTER	2
	4	ENTER	5
	4		5

7 8

0

1

3

2

6

9

4

POWER

NUMBER

TV Multi-Brand Remote Control

The VCR's remote control can control several functions on JVC remote control TVs and on the brands of remote control TVs listed below. *The default setting is JVC code 01.

TURN ON THE TV

1 Turn the power on using the TV's remote control.

SET TV BRAND CODE

Refer to the chart in the left column. While holding down

TV on the VCR's remote control, press MBR SET and enter

2 your TV’s brand code using the NUMBER keys, then press

STOP.

Follow the example shown below.

The TV's power should go off. If it does, try other

operations ( step 3).

Once you have set the remote control to operate the

TV, you don’t have to repeat this step until you

STOP

3

TV CH+/–

TV VOL +/–

	replace your remote control’s batteries.
	PANASONIC has two codes. If the TV does not
	function with one code, try entering the other.

3	OPERATE TV
	First, while holding down TV, press the corresponding
	button: POWER, TV CH +/–,TV/VCR, TV VOL +/–,
	NUMBER keys.
	For some brands of TV, you must press ENTER after
	having pressed the NUMBER keys.

NOTE:

Depending on the type of TV, there may be cases where some or all functions cannot be operated using the remote control.

TV BRAND NAME	BRAND CODE
JVC	01
MAGNAVOX	02
MITSUBISHI	03
PANASONIC	04, 11
RCA	05
SHARP	06
SONY	07
TOSHIBA	08
ZENITH	09
HITACHI	10
SAMSUNG	12
SANYO	13
SEARS	13

(Ex.) To set remote control to RCA 05:

	MBR SET
TV	A/B
	0	5	STOP
	0	5
Hold	Press in succession
down

Release

Image 56

Contents SR-TS1U Dear Customer Power Sources Power Cord ProtectionPower Lines Grounding or PolarizationAccessories Damage Requiring ServiceCleaning Replacement PartsContents Connections Connect VCR to TV Installing/Removing the lithium batteryBack of VCR Plug & Play Setup Plug & PlayEN I Nitial Sett Ings Auto Clock Set/Auto Tuner SetInformation Clock Select D.S.T. Mode SET Auto Clock to onSelect Host Channel Semi-AutoSelect Time Zone Return to Normal ScreenSET Time SET DateAccess Main Menu Screen TunerSET Set Receivable ChannelsAccess Manual ChannelAdd Or Delete a Channel Or Shuttle Plus #Cable Box Control Situate ControllerAttach Controller Connect Cable BOX to VCRAccess Cable BOX SET Screen Turn on Cable BOXSelect Cable BOX Output Channel Set Cable Box Output Channel & Cable Box BrandBrand Code Access Cable BOX Brand SET ScreenEnter Cable BOX Brand DBS receiver DBS Receiver ControlConnect DBS Receiver to VCR Access DBS Receiver SET Turn on DBS ReceiverSelect DBS Receiver Output ChannelAccess DBS Receiver SET DBS Receiver BrandDBS Receiver Code from Following list, then Press OK JVC Dish Network Echostar Dish NetworkSimple Playback Load a CassetteFind Program Start Point Start PlaybackSimple Recording Playback Features Activate FRAME-BYFrame Playback Playback and Recording FEA Tures E NAccess Distant Code Engage Manual Tracking ModeAdjust Manual Tracking Activate HIGH-SPEED SearchSelect Picture Control SET ModePicture Control Shuttle Plus #to select Select Audio MonitorSelect The Soundtrack Shuttle Plus # to set to Video StabilizerActivate Video Stabilizer Instant ReView Returning PositionReview Or Shuttle PLUS%ÞCounter Reset Tape Position IndicatorRepeat Playback Next-Function MemoryAudio mode Counter reading Indications Operation modeSuperimpose Tape speed indication Cassette Loaded markMovie Advance Press Skip SearchTo S Video OUT Video Cable Supplied To Remote To Audio Series PlaybackTo S Video OUT Video Cable Supplied Make Connections Turn on ALL ComponentsLoad Cassettes Press Play on either of SR-TS1USeries Recording CamcorderPrepare for Recording SET Recording VCR’S Input ModeTurn on ALL Components Active Video Calibration Video CalibrationStart Playback PlaybackRecording Recording Features Record Safety SET ScreenOr Shuttle Plus Shuttle Plus # to selectVHS Super VHS, S-VHS ET and VHS Access Function SET 1 ScreenSelect S-VHS Mode Super VHS ET Select S-VHS ET SETMode To Record SAP Programs Select 2ND Audio Record SET ModeStereo And SAP Second Audio Program VCR Plus+ Timer Programming Timer RecordingInput Receiving Channel Number Enter Pluscode NumberSP/EP ProgramInitial SET, then press VCR Plus+ SetupVCR Plus+ Guide Channel Matching Access Guide Channel SET Screen EN Timer RecordingEx. When inputting the Guide Channel number 6 for WNJUInd Input Guide Channel NumberExpress Timer Programming Access VCR PLUS+SET Program Date SET Channel NumberEngage Timer Mode Cancel or Revise a RE-ENGAGE TimerCheck, Cancel And Revise Programs ProgramAuto Timer Select Auto SP EP Timer SET ModeAuto SP→EP Timer Instant Timer Recording ITR Engage ITR ModeSET Recording Duration Press REC on the front panelBefore performing the following steps Engage Auto Satellite Prog REC ModeAutomatic Sat- ellite Program Recording Edit To Or From Another SET RECORDER’S InputSelect Edit for PIC Start PlayerEdit From a Camcorder PlayerSet your VCR to its record mode Select Rear AUX Input SET ModeSet the camcorder to its play mode TV Multi-Brand Remote Control Turn on the TVSET TV Brand Code Operate TVCable Box Multi-Brand Remote Control Turn on the Cable BOXOperate Cable BOX Cable BOX Brand Name Brand CodeEN Special Features DBS Receiver Multi-Brand Remote ControlTurn on the DBS Receiver Enter DBS Receiver BrandUnplug Vcrs Power SET Remote ControlPlug in Power Cord Turn VCR Power onCassette gets stuck partway Make sure the cassettes window isProcedure Those in the previous area Timer againRe-perform the VCR Plus+ setup Doesn’t work properly Troubleshooting Other ProblemsQuestions and Answer S E N Can the VCR indefinitely remain in the still mode?Can the VCR indefinitely remain in the Record-Pause mode? What happens if the tape runs out during recording?EN Index List Of TermsFront View Index Front Display PanelRemote Control Cassette Failure to heed the following precautions may resultDamage to the VCR, remote control or video Memo Memo Memo SR-TS1U