JVC BR-D95U specifications Preparation, Operation Mode Lock

5 MENU SWITCH SETTING DETAILS
5-2 MENU SWITCH SETTING CONTENT
	[ ] : Factory setting
	Item		Setting
Menu SW	On-screen	Counter	On-screen
No.	display	display	display
512	MUTING/ALARM	[0]	[OFF]
	MESSAGE	1	ON

Content

Selects whether “MUTING” or “CONDITION

ALARM” messages appear On-Screen.This menu

makes it easier to check the VCR’s operation

status.

The on-screen display is shown on the monitor

connected to the [VIDEO MONITOR OUT]

connector.

OFF : The “MUTING” and “CONDITION ALARM”

are not displayed.

ON : The “MUTING” and “CONDITION ALARM”

are displayed.

For more details, refer to the “MUTING/

CONDITION ALARM” display on page 24.

6 PREPARATION

6-1 OPERATION MODE LOCK

This unit is provided with an operation mode lock facility. This function prevents accidental changes to switch and control settings. When this function is ON, currently selected modes and knob or switch positions cannot be adjusted.

●Use menu switch No. 002 <OPERATION LOCK> to enable this function.

●With this function enabled, operation of all front panel control buttons, adjustment knobs, dials and switches is disabled and changes to menu switch settings are not possible. When this function is activated, it is not possible to change menu switch settings. However, the [PHONES LEVEL] control and menu switch No. 002 <OPERATION LOCK> (to release the operation mode lock function) can be used.

Procedure

						[SEARCH] button
						VIDEO CASSETTE RECORDER	BR-D95U
AUDIO INPUT / AUDIO MONITOR SELECT							POWER
SDI	CH1	CH2	CH3	CH4	SIF
AES/EBU	CH1	CH2	CH3	CH4	LINE	ON	I
L
ANALOG	CH1	CH2	CH3	CH4	CPN	COMPONENT DIGITAL	O
R						OFF

Variable Motion

513	EDIT ON	0	OFF
	SCREEN	[1]	[ON]

<TBC. FRAME MEMORY>

Selects whether the edit on-screen display is ON or

OFF during editing. On-screen information is output

from the [LINE2 SUPER OUT] connector.

OFF : Does not show the edit on-screen display

during editing.

ON : Show the edit on-screen display during

editing.

	CH1	CH2	CH3	CH4/TRACKING
PHONES	CH1	CH2	REC CH3	CH4	TRACKING
		PULL FOR VARIABLE			METER MODE
PULL
RELEASE			PLAY

CTL TC UB DF SERVO CF GEN 16:9 AP	525	CONDITION	COUNTER	RESET	VCON	REMOTE
AUTO OFF P.READ V.VAR PB/EE REMOTE	625		UB
			MENU	SET	HOLD	PB
						PB/EE

										STILL
	H	M	S		F
ASSEM VIDEO		DA1	DA2 DA3	DA4	EJECT	REC	PLAY	PAUSE/STILL
									X-1	X1
IN	ENTRY	OUT	INSERT	TC	TOP		VIDEO	AUDIO
	CANCEL PREVIEW		AUTO EDIT	PREROLL	STAND BY	REW	STOP	FF
										PULL
SHIFT		REVIEW		USER	SERVO/SYS	TIME CODE ON SCREEN		OTHERS		RELEASE
									REV	FWD
[MENU] button										Jog dial
	[SET] button

601	V.BLANK MASK	0	OFF
		[1]	[ON]
		2	ON WITH
			0.5H

620	DUBBING LOOP	[0]	[OFF]
		1	3 TIMES
		2	5 TIMES
		3	10 TIMES

Enables/disables masking of the vertical interval.
OFF	: No masking.
ON	: Masks the vertical interval.
ON WITH 0.5H : Masks section for 0.5H in addition
	to the vertical interval (analog
	signals only).

*When this menu is set to “OFF”, only the recordable sections of the signals output for V. blanking in the EE mode are output (VITC,

EXTRA LINE, EXTENSION LINE).

When this menu is set to “ON”, VITC and EXTRA LINE have priority in each menu setting (refer to page 89).

Selects whether or not the multi-generation test
“Dubbing Loop Function” is used to aid adjusting an
analog component system to unity gain. When this
mode is active, the VCR automatically switches to
its internal color bar generator and continuously
builds the number of generations selected.
OFF	: The dubbing loop function is disabled.
3 TIMES	: The dubbing loop function repeatedly
5 TIMES	builds 3 generations every few seconds.
	: The dubbing loop function repeatedly
	builds 5 generations every few seconds.
10 TIMES : The dubbing loop function repeatedly
	builds 10 generations every few
	seconds.

*When set to any setting except OFF (0), this unit enters the Dubbing Loop mode.

*For more details on the dubbing loop function, refer to page 122.

[HOLD] button

1.Make all desired settings and operate as usual.

2.Engage1 the operation lock function.

2Press the [MENU] button to call up the menu setting display.

Turn the jog dial and select menu switch No. 002 <OPERATION LOCK>.

If the Direct Access facility is ON, press the [STAND BY] button to call up the 3menu item display more quickly.

4Select “ON (1)” by turning the jog dial while pressing the [SEARCH] button. Press the [SET] button.

The operation lock function is ON.

After the SET indication blinks for several seconds, the normal counter and on-screen displays are restored.

3.To cancel the operation mode lock facility, set menu switch No. 002 <OPERATION LOCK> to “OFF (0)”.

64 65