JVC BR-D95U $PB PB/EE button, Vcon button, Counter button, Video Input indicators,
SET button

2 CONTROLS, CONNECTORS AND DISPLAYS

2-1 FRONT PANEL

2 CONTROLS, CONNECTORS AND DISPLAYS

2-1 FRONT PANEL

$[PB PB/EE] button

Press to select the playback (PB) exclusive mode

or PB/EE auto switching mode. The selected mode

is shown by the indicators in the upper section of

LINE: Lights when composite video signal input (via rear panel's [COMPOSITE LINE IN] connector) is selected. CPN: Lights when component video signal input

28 25

VIDEO CASSETTE RECORDER BR-D95U

the counter display. When the PB/EE Auto

Switching mode is engaged, set the VCR to the EE

%mode with menu switch No. 314 <PB/EE MODE>.

[REMOTE] button Press to select remote/local operation. When remote operation is selected, ÒREMOTEÓ is shown in the upper section of the counter display. In the ÒREMOTEÓ mode, the unit can be operated via the remote controller connected to the rear panelÕs [REMOTE IN (9P)] or [RS-232C] connector. On the VCR itself, only the [STAND BY], [STOP] and [EJECT] buttons will remain operable. To operate the VCR locally, that is with its operation buttons, press the [REMOTE] button so

(via rear panel's [COMPONENT IN] connector) is selected. All lit: All indicators light when the signal from the internal signal generator is selected. The type of signal can be selected with menu switch No. 111 ÒREC SIGNAL SELECTÓ. Blinking: The indicator blinks if no signal is input or

qif the wrong type of signal is input.

[AUDIO INPUT/AUDIO MONITOR SELECT] indicators Show whether the input or monitor audio signal is selected. Press the w[AUDIO INPUT] button or [AUDIO MONITOR] button to switch between

AUDIO		AUDIO INPUT / AUDIO MONITOR SELECT							VIDEO
INPUT									INPUT
		SDI	CH1	CH2		CH3	CH4		SIF
AUDIO	AES/EBU		CH1	CH2		CH3	CH4		LINE
MONITOR		L
	ANALOG		CH1	CH2		CH3	CH4		CPN
		R
		CH1	CH2			CH3	CH4/TRACKING
	R	P	R	P	R	P	R	P
	dB OVER dB		dB OVER dB		dB OVER dB		dB OVER dB
	+4	0	+4	0	+4	0	+4	0
	+2	–10	+2	–10	+2	–10	+2	–10
	0	–20	0	–20	0	–20	0	–20
	–2	–30	–2	–30	–2	–30	–2	–30
	–4	–40	–4	–40	–4	–40	–4	–40
		–60		–60		–60		–60
PHONES		CH1	CH2	REC		CH3	CH4		TRACKING
			PULL FOR VARIABLE						METER MODE
									FINE	TRACKING

PULL

RELEASE

PLAY

						COMPONENT DIGITAL
					Variable Motion
CTL TC UB DF SERVO CF GEN 16:9 AP				525	CONDITION		COUNTER	RESET	VCON	REMOTE
AUTO OFF P.READ V.VAR PB/EE REMOTE				625			UB
							MENU	SET	HOLD	PB
										PB/EE
	H		M	S	F
ASSEM	VIDEO	DA1	DA2	DA3	DA4	EJECT	REC	PLAY		PAUSE/STILL
IN	ENTRY	OUT	INSERT		TC
						TOP		VIDEO		AUDIO
	CANCEL PREVIEW		AUTO EDIT		PREROLL	STAND BY	REW	STOP		FF
SHIFT		REVIEW			USER	SERVO/SYS	TIME CODE	ON SCREEN		OTHERS

		POWER
	ON	I
	OFF	O
		12
SEARCH VAR	PLAYER RECORDER
		27
P.PLAY
	STILL
X-1		X1
		PULL
		RELEASE
REV		FWD

^that the ÒREMOTEÓ indicator goes out.

[VCON] button

Press to adjust the video/audio parameters. Adjustable items are shown on the counter display. Turn the jog dial while pressing the [SEARCH] button to make adjustments.

You can adjust the video parameters by connecting an optional video controller to the rear panelÕs

&[VIDEO CONTROL] connector. (See page 118.)

[RESET] button Press to reset the CTL counter to Ò0:00:00:00Ó. The time code and user bits cannot be reset. When the edit points have been set, these settings are canceled. When setting the fixed time cue up, press this button to reset the counter to Ò00:00:00:00Ó. For

*details, refer to ÒFixed Time SettingÓ on page 91.

[COUNTER] button

Press to switch the counter between CTL counter, time code, or user bits display. Press this button while pressing the [SHIFT] button to display user bits.The selected counter display mode is shown by the indicators in the upper section of the counter display. CTL: CTL counter display

TC: Time code display (UB: User bits display

Input video signal button Press to select input video signals. The selected video signal is shown by the )[VIDEO INPUT] indicators. SIF can only be selected when the optional SA-D95U digital interface board is installed. A menu switch is provided to prevent misoperation. Refer to the menu switch setting for

)No. 371 ÒINPUT SELECT SAFETYÓ.

[VIDEO INPUT] indicators

Show the type of video signal selected with the ( input video signal switch.

SIF: Lights when serial video signal input (via rear panel's [SERIAL V/A IN] connector) is selected.

the input or monitor indication.The channel indicator blinks if the selected signal does not conform to the standard. Along with the input indication, the type of signal (SDI, AES/EBU or ANALOG) is shown. With the monitor indication, the audio channel (CH1, CH2, CH3, or CH4) output to the monitor output L or R channel is shown.The channels can be switched with the raudio signal select buttons. When these three indicators (SDI, AES/EBU, ANALOG) are lit simultaneously, audio signals (1 kHz sine wave) from the built-in signal generator are selected. The signals from the built-in signal generator can be either 1 kHz audio signals or no sound. This is selectable with menu switches (No. 253 to No. 256). When the input audio signal indication is selected, these indicators blink if no SDI or AES/EBU signal is input. SDI and AES/EBU can only be selected when the optional SA-D95U digital interface board

wis installed.

[AUDIO INPUT] button

Press to select the input audio signal for the

[AUDIO INPUT/AUDIO MONITOR SELECT] eindicators. The button illuminates when selected.

[AUDIO MONITOR] button Press to select the monitor audio signal for the [AUDIO INPUT/AUDIO MONITOR SELECT]

rindicators. The button illuminates when selected.

Audio signal select buttons

Press to select the input audio signal or monitor audio signal.

The selected audio signal is shown by the q

[AUDIO INPUT/AUDIO MONITOR SELECT] indicators.

29

tSetting buttons

[MENU] button

●Press this button to enter the Menu Switch Setting mode.

Press this button again to switch back to the Counter Display mode.

[SET] button

●Press this button to store menu switch setting data in the VCRÕs memory.

●Press this button to preset data in the time code generator.

●Use this button to end video parameter adjustment or to use the counter memory function.

[HOLD] button

●Press this button to preset data in the time code generator. To preset time code, the [COUNTER] switch must be set at ÒTCÓ. To preset user bits, the [COUNTER] switch must be set at ÒUBÓ.

*This button is effective only when the [INT/EXT] switch on the time code setting section is set to ÒINTÓ and the [PRESET/REGEN] switch is set to ÒPRESETÓ.

26

yOperation buttons

●All buttons are illuminated when pressed.

●The labels printed under the operation buttons indicate the menu items displayed when the button is pressed in the Menu Switch Setting (Direct Access) mode.

[EJECT] button

●Press to eject the cassette.

●TOP menu switch items are displayed when

this button is pressed in the Menu Switch Setting mode.

[REC] button

●Engages the Record mode when pressed together with the [PLAY] button.

●To monitor the EE picture during playback, press and hold this button.

●Press this button in the Stop mode to check

preset data in the time code generator.

[PLAY] button

●Press to start playback. If pressed together with the [REC] button, recording will start.

●Video menu switch items are displayed when this button is pressed in the Menu Switch Setting mode.

●When menu switch No. 301 <DIRECT SEARCH> is set to ÒOFFÓ, hold this button down and turn the search dial during play to perform variable slow playback.

●By turning the jog dial while pressing this button in the Play mode, you can vary playback speed between 0 (Still) and +2 (double-speed) Refer to ÒSimplified playback speed adjustment functionÓ on page 84.

●In the Program Playback mode, hold the @ [VAR/P.PLAY] button down and press this button to execute program playback.

14 15