JVC BR-D95U specifications Specifications, Unit mm, 150

Page 76

16 SPECIFICATIONS

General

Format

 

Type D-9 (Digital S)

Tape width

12.65 mm

Tape speed

57.737 mm/sec. (525), 57.795 mm/s (625)

Signal format

NTSC standard (525), PAL standard (625)

Dimensions

429 mm (W) x 189 mm (H) x 569 mm (D) (16-15/16" x 7-1/2" x 22-7/16")

Weight

 

Approx. 22 kg (48.5 lbs.)

Power consumption

Approx. 1.7 A to 0.8 A

Power supply

AC 110 V to 240 V ~, 50 Hz/60 Hz

Record/play time (w/DS-104)

(Record/play) Approx. 104 min.

REW/FF time (w/DS-104)

Approx. 3 min.

Operating temperature

5˚C to 40˚C (41˚F to 104˚F)

Storage temperature

-20˚C to 60˚C (-4˚F to 140˚F)

Operating humidity

30% to 80%RH

 Video signal

 

Input

Composite

1 Vp-p, 75 ohms, unbalanced

 

Component

Y: 1 Vp-p/R-Y, B-Y, 0.7 Vp-p, 75 ohms, unbalanced

Output

Composite

1 Vp-p, 75 ohms, unbalanced

 

Component

Y: 1 Vp-p/R-Y, B-Y, 0.7 Vp-p, 75 ohms, unbalanced

External input

0.43 Vp-p (B.B) (525), 0.45 Vp-p (B.B) (625), 75 ohms, unbalanced

Sampling frequency

Y: 13.5 MHz, R-Y/B-Y: 6.75 MHz

Quantization

8 bits

Frequency range

Y: 0 - 5.75 MHz, +1.0 dB/-3.0 dB (analog component in/out)

 

 

R-Y/B-Y: 0 - 2.75 MHz, +1.0 dB/-3.0 dB

S/N

 

More than 50 dB (analog composite in/out)

 

 

More than 55 dB (analog component in/out)

 

 

More than 60 dB (digital in/analog component out)

Audio signal

Input

Line input

-20/-6/0/+4 dBs, high impedance, balanced

Output

Line output

-6/0/+4 dBs, low impedance, balanced

 

Monitor output

-6/0/+4 dBs, low impedance, balanced

 

Headphone

-to -14 dBs, 8 ohms

Sampling frequency

48 kHz

Quantization

16 bits

No. of channels

4

Frequency response

20 Hz to 20 kHz

Dynamic range

85 dB or more

Wow & flutter

Below a measurable value

 Time code

 

LTC input

0 ± 6 dBs, high impedance, balanced

LTC output

0 ± 3 dBs, low impedance, balanced

 Accessories

Power cable (A Type: 125 V, 7 A / C Type: 250 V, 10 A)

 

 

Repeat Tye x 1

When the optional SA-D95U is installed

Serial video/audio input

Conforming to SMPTE259M/CCIR656-III

Serial video/audio output

Conforming to SMPTE259M/CCIR656-III, 800 mVp-p ± 10%

Digital audio input

1

Vp-p, 75 ohms, unbalanced, conforms to AES/EBU standard

Digital audio output

1

Vp-p/3 Vp-p or more (switchable with built-in switch), 75 ohms, unbalanced,

 

conforms to AES/EBU standard

Design and specifications subject to change without notice.

16 SPECIFICATIONS

Unit: mm

16

 

569

429

22.5

 

VIDEO CASSETTE RECORDER BR-D95U

Variable Motion

Design and specifications subject to change without notice.

174

15

150

151

Image 76
Contents BR-D95U This instruction book is made from 100% recycled paperImportant Safeguards This unit should be used with 120 V AC onlyPort Cable Length Main Features ContentsMaintenance IntroductionOutline Other FunctionsHead Cleaning PrecautionsVideo Cassette Front Panel Video Input indicators Audio signal select buttonsSetting buttons  Menu button $PB PB/EE button PAUSE/STILL SUB Panel Rear PanelCounter Display ON-SCREEN Display Operation mode display in the Variable MUTING/CONDITION Alarm displayConnections Input ConnectionsEditing remote control connection Output ConnectionsControl System Connections Composite OUTMenu Switch Setting 00A Menu SettingMenu Display Modes 00F Fixed Time EntryVideo Signal System Selection PALSaving and Calling UP Menu Switch Settings Enabling the Direct Access functionAccess ÒonóChanging the registered menu switch setting Erasing all registered items on the User Activating the menu switch lock functionErasing registered items one at a time Recording Current Adjustment Activating the recording current adjustment functionMenu Switch List Menu Switch Setting DetailsFunctions enclosed Are not available on the PAL system Menu Switch Setting Content ECC Mode VD REC SignalNormal Slow Picture FrameLine Setup WideExtra Line PB MutingVblank Ycomb OFF on OFF WITH21 VblankFactory setting AT 2CH CH1 0DBCH2 CH3PB/EE Mode SettingSilence PAUSE/STILL SEC STP/TIMEDiag AT OFF Power on 0SEC15SEC StillSwap Mode Disable SafetyTime Code PARA-RUN OFFSynchro Disable Nization Enable Regen ModeCF Flag Reply FLDUB Preset OFF Auto Mode ASM INS 0FFRemain Enable EXT LTC Regen TC VitcOperation Mode Lock PreparationLoading the cassette Turn the Power switch on Remove the cassette from the slot PrecautionsStandby ON/OFF Load the cassetteRecording Input Video and Audio Signal SelectionPreparation for Recording Audio Monitor Output Signal Selection Audio Record Level AdjustmentBasic Recording Operations Playback Digital Audio Signal INPUT/OUTPUTPreparation for Playback Audio Playback Level Adjustment Audio Playback Level Lock modeManual audio playback level adjustment Basic Playback OperationsPlay volume control Set menu switch No Auto Tracking to OFFAdjust until the tracking meter level reaches the maximum Manual Tracking AjustmentSimplified Playback Speed Adjustment Function Error CorrectionAudio V. Fade Function Shuttle SEARCH/JOG Operation Variable Slow PlaybackTo stop search operation Jog operation Turn the inner jog dialProgram Playback User Setting Other Functions11 FF, REW and Counter Memory Functions Extra Line Data RECORDING/PLAYBACKSignals. Factory setting Auto When video signals are output, extra lineExtra line data playback Line recordingSimultaneous Operation Fixed Time CUE UP FunctionEngage the Multi Cue-Up mode Quit the Multi Cue modeMulti CUE-UP Function Cue Operation buttons DisplayStriping REC Menu Striping RECHOW to USE Time Code Time Code Initial Setting PresetFront sub panel switches for time code setting Time Code DisplayTime Code Recording Time Code Playback Front sub panel switch settingRecord the time code Time Code Switch Setting for Editing SUB Time Code Recording and PlaybackEditing Assemble editing Insert editingRecording PlaybackEditing procedure Color Frame Servo SettingPreparation Swap Editing Editing mode selectionEdit point entry Preview editing Editing actualReview check Correcting the edit pointAudio Split Editing Other FunctionEditing with the PRE-READ Function Manual EditingEditing System Phase Adjustment Example of editing system configurationThat allows you to bypass the frame memory Refer toSelect the adjustment item by turning the jog dial Adjustment items on screen can be selected with the cursorRepeat steps 2 to 3 to adjust other items Item belowAdjustment Dubbing Loop Function 122Basic Table JVC-1 Table0A ACK 0B NAKFlag Reset Out Flag Reset3F Stop Key CueUp With DataB6 Rev Shuttle Key C0 Auto Edit KeyExecutes Auto Edit on the VCR C1 Preview Key Basic TableE4 Out Data Preset E6 Preroll TimePreset Basic TableE7 Timer Mode Select E5 Edit PresetF6 JVC On F7 Basic Table OnFA Rec/DubRequest FB VTR INDSpeed/data correspondence table For the current timer mode Timer modeCurrent timer mode Bit-3 Auto modeDATA0 0A DATA0 0BDATA0 1B DATA0 0EDATA0 0F DATA0 1FDATA0 1D On-screen display TroubleshootingCode Troubles not to be Warned by Indicators Symptoms Cause Not operable Remote button is set to RemoteOn-screen display Behavior and actions to be taken ActionOptional Accessories AppendixUnit mm Specifications150