Magnavox SVB106 owner manual Turning on Your VCR, Below will appear

Page 11

●Before turning on your VCR, make sure there are batteries in the remote control and the VCR and TV are connected (see pages five-10).

●You can not set up channels if you are using a Cable Box/DBS.

●The instructions on this page only work when you turn on the VCR for the first time. If there is a power failure or if the VCR is unplugged for more than one minute, you may need to repeat the instructions on this page.

1

Press the POWER button. The POWER light and the VCR/TV light will appear.

2

Turn on the TV. Set it to the same channel as the CH3/CH4 switch on the back of the VCR. The menu shown

below will appear.

LANGUAGE SELECT

B ENGLISH

[ON]

ESPAÑOL

3

Press the PLAY button or the STOP button to select ENGLISH or ESPAÑOL. [ON] will appear beside your choice.

4

Press the F.FWD button or the MENU button. AUTO SET UP will appear on the screen.

AUTO SET UP

5

Press the MENU button, the F.FWD button, or the REWIND button to begin automatic channel setup. AUTO SET UP will flash on the screen and channels will count up on the screen as setup progresses. When channels are set up, the TV will go to the lowest channel available.

The VCR will memorize all available channels, so when you use the CHANNEL o/p buttons, you’ll only scan through channels that you receive.

Turning on Your VCR 11

2Turn on the TV.

1

5 4

3

Helpful Hints

•If you do not see any on-screen dis- plays when you turn on the VCR, check your hookups, then try again. If you still do not see any on-screen displays, follow the steps under “Automatic Channel Setup” on page 12 and “Language Selection” on page 16.

•If you try to set up channels when there is no antenna or cable con- nected to the VCR, programming will appear to take place. Eventually, AUTO SET UP will appear on the screen steadily, and channel programming will stop. Connect an antenna or cable to the ANT(enna) IN jack of the VCR, then press the MENU button, the F.FWD button, or the REWIND button again. Channel programming will begin again.

Image 11

Contents Video Cassette Recorder For Customer Use Warranty VerificationDeclaration of Conformity FeaturesSafety Precautions IntroductionTable of Contents VCR maintenance Before Using Your VCRPutting Batteries in the Remote Control Using the Remote ControlDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemHookups Without a Cable Box/Direct Broadcast System cont’d Plug in the AC power cords of the TV and the VCRRecording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections TV’s Antenna Jack Cable Box/DBS RF coaxial SignalRecording One Channel/Watching Another Hookups With a Stereo TV Below will appear Turning on Your VCRPress the Menu button until Menu 1 appears Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dFollow the steps below to set your VCR’s clock. Make sure Setting the ClockSetting the Clock cont’d Language Selection Press the Counter RESET/EXIT button to exitOn-Screen Status Displays OFF mode Press the Display button once. Count modePress the Display button once Clock mode Press the Display button once OFF modeRecord Button Remote Control ButtonsPower Button Number ButtonsIndex Search Button Counter RESET/EXIT ButtonEject Button Time Search ButtonVCR Display Panel Front Panel Video OUT Jack AC Power CordRear Panel Audio OUT JacksRead and follow the steps below to play a tape PlayingVHS Quasi Play Back Sqpb Recording Stopping an OTR One-Touch RecordingStarting an OTR Channels are set up Clock is set Timer RecordingEnter the recording’s start time Timer Recording cont’dRepeat the procedure in to set the recording’s end time Start Time END Time Channel REC Speed SLP Cancelling a Timer Recording Timer Recording cont’dCorrecting a Timer Recording Auto Satellite Link Using a Satellite Tuner Recording One Channel/Watching Another Rerecording Tape Duplication Repeat Play Viewing a Slow Motion Picture Forward and Reverse Searching SP/LP/SLPSuper High Speed Searching LP/SLP Viewing a Still PictureAppear at the bottom of the screen Picture SelectPress the Play button to watch the tape Real-Time Counter MemoryPress the Index Search button Index SearchPress the Time Search button Time SearchTo resume normal tape playback, press the Play button Quick FindPress the QUICK-FIND button Automatic Playback Features Or Receiver MTS Broadcast Stereo SystemUnderstanding On-Screen Displays MonitorPress the Menu button repeatedly until Menu 2 appears MTS Broadcast Stereo System cont’dPlease see additional notes on Press the Counter RESET/EXIT buttonHi-Fi Stereo Sound System Cable Box/DBS Output Channel Channel 3 or GlossaryHelpful Hints Helpful Hints cont’d Video Cassette Recorder or Player Limited WarrantyCheck or money order Account number Limited Warranty cont’dTo obtain a replacement product from Philips Payment AmountSpecifications 12, 33 Broadcast Power17-18 Recording Timer Second audioSupplied Accessories