Magnavox SVB106 owner manual Recording

Page 24

24 Recording

Read and follow the steps below to record a television program.

1

Turn on the TV; set it to channel 3 or 4, whichever chan- nel the CH3/CH4 switch on the back of the VCR is set to.

2

Insert a tape with its record tab intact (see page five) in the VCR. The POWER, VCR/TV, and CST.IN lights will appear.

3

If the VCR/TV light does not appear, press the VCR/TV button so that the VCR/TV light appears.

4

Press the SPEED button until the desired tape speed (SP or SLP) appears on the screen. The tape speed will disappear after about five seconds.

You can change the tape speed while the VCR is recording, but some distortion may appear on the tape. Details about tape speed are on page 45.

5

Use the CHANNEL o/p buttons or the Number buttons to select the channel to be recorded.

6

Press the RECORD button once to start recording. The REC(ord) light will appear. If the tape is missing the record tab, the VCR will eject the tape.

7

To pause the recording (for example, during commer- cials), press the PAUSE/STILL button once. The REC(ord) light will flash.

To resume recording, press the RECORD button or the PAUSE/STILL button again. The REC(ord) light will appear.

8

Press the STOP button to stop recording.

1Turn on the TV.

2 Insert a tape.

3

5

4

67

8

Helpful Hints

•Other recording options are on pages 25-33.

•The VCR will record in a preset vol- ume.

•Pause mode will automatically switch to Stop mode after five min- utes to protect the VCR and the tape from damage. When a record- ing is paused, you may review the pause time remaining with the ■ marks on the screen. Each ■ mark equals one minute remaining. During the last minute of paused recording, the ■ mark will flash.

•If any menu is activated on the TV screen, the RECORD button on the remote control does not function.

Press the COUNTER RESET/EXIT button to remove the menu. Then, press the RECORD button.

Image 24

Contents Video Cassette Recorder Warranty Verification For Customer UseFeatures Safety PrecautionsIntroduction Declaration of ConformityTable of Contents Before Using Your VCR Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenanceHookups Without a Cable Box/Direct Broadcast System Disconnect the antenna or cable from your TVPlug in the AC power cords of the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’dHookups With a Cable Box/Direct Broadcast System ConnectionsRecording/Viewing Any Channel Cable Box/DBS RF coaxial Signal Recording One Channel/Watching AnotherTV’s Antenna Jack Hookups With a Stereo TV Turning on Your VCR Below will appearAutomatic Channel Setup Press the Menu button until Menu 1 appearsAutomatic Channel Setup cont’d Adding/Deleting ChannelsSetting the Clock Follow the steps below to set your VCR’s clock. Make sureSetting the Clock cont’d Press the Counter RESET/EXIT button to exit Language SelectionOFF mode Press the Display button once. Count mode Press the Display button once Clock modePress the Display button once OFF mode On-Screen Status DisplaysRemote Control Buttons Power ButtonNumber Buttons Record ButtonCounter RESET/EXIT Button Eject ButtonTime Search Button Index Search ButtonVCR Display Panel Front Panel AC Power Cord Rear PanelAudio OUT Jacks Video OUT JackPlaying VHS Quasi Play Back SqpbRead and follow the steps below to play a tape Recording One-Touch Recording Starting an OTRStopping an OTR Timer Recording Channels are set up Clock is setTimer Recording cont’d Repeat the procedure in to set the recording’s end timeEnter the recording’s start time Start Time END Time Channel REC Speed SLP Timer Recording cont’d Cancelling a Timer RecordingCorrecting a Timer Recording Auto Satellite Link Using a Satellite Tuner Recording One Channel/Watching Another Rerecording Tape Duplication Repeat Play Forward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPViewing a Still Picture Viewing a Slow Motion PicturePicture Select Appear at the bottom of the screenReal-Time Counter Memory Press the Play button to watch the tapeIndex Search Press the Index Search buttonTime Search Press the Time Search buttonQuick Find Press the QUICK-FIND buttonTo resume normal tape playback, press the Play button Automatic Playback Features MTS Broadcast Stereo System Understanding On-Screen DisplaysMonitor Or ReceiverMTS Broadcast Stereo System cont’d Press the Menu button repeatedly until Menu 2 appearsPress the Counter RESET/EXIT button Hi-Fi Stereo Sound SystemPlease see additional notes on Glossary Cable Box/DBS Output Channel Channel 3 orHelpful Hints Helpful Hints cont’d Limited Warranty Video Cassette Recorder or PlayerLimited Warranty cont’d To obtain a replacement product from PhilipsPayment Amount Check or money order Account numberSpecifications Power 17-18 Recording TimerSecond audio 12, 33 BroadcastSupplied Accessories