Magnavox ZC320MW8B/F7 owner manual Timer Recording, To stop the timer recording in progress

TIMER RECORDING

To stop the timer recording in progress

1)Press [STOP C ] on the remote control.

2)Confirmation message will appear. Select “Yes”, then press [OK].

•To stop the timer recording immediately, press [CSTOP] on the unit.

Checking, canceling, or correcting the timer programming information

1)Press [STANDBAY/ON y].

2)Press [TIMER PROG.].

3)Check the information.

Timer Programming

JAN/ 7/11 12:00 AM L1 SP
SP (1:00)		THU JAN/06 11:00AM
Date	Start	End	L1/L2
JAN/07	12:00AM	1:00AM	L1
	New Program

4-A) To delete the timer program:

1 Use [K / L] to select the program you want to delete, then press [OK].

2 Use [K / L] to select “Delete”, then press [OK]. Confirmation window will appear.

3 Use [K / L] to select “Yes”, then press [OK].

4-B) To correct the timer program:

1 Use [K / L] to select the program you want to correct, then press [OK].

2 Use [K / L] to select “Program Change”, then press [OK].

3 Correct the timer program by using [K/ L/ {/ B], then press [OK].

5)Press [TIMER PROG.] to exit.

6)Press [STANDBAY/ON y] to return to the timer standby mode.

Note

•Press [TIMER PROG.] to check the timer recording in progress.

When the timer recording is proceeding, that program will be highlighted with red. In this case, you cannot select any other program.

Putting Names on Timer Programs

1)In stop mode, press [TIMER PROG.].

2)Use [K / L] to select the program you want to edit the timer program name, then press [OK].

3)Use [K / L] to select “Edit Title Name”, then press [OK].

Program Change

Delete

Edit Title Name

A window for entering a title name will appear.

Timer Programming Edit Title Name

FEB/05/11 10:30 AM L1 SP
SP (1:00)				THU FEB/03 11:30AM
Date	Start		End		L1/L2
JAN/07	12:00A	A B		C	L1
		a	b	c
		1	2	3
		@ !		?
					1/1

4)To enter a title name, follow the steps of “Guide to Edit Title Name” on page 58.

5)After entering a title name, press [OK].

6)Use [K / L] to select “Yes”, then press [OK].

•The program name is now updated.

If the timer program did not complete correctly, the error number appears in the timer programming list.

			Timer Programming
					FRI JAN/07 11:00AM
			Date	Start	End	L1/L2
		E41	JAN/07	12:00AM	1:00AM	L1
				New Program
						1/1
Each error number means:
E1-22	Recording error other				E41	Power failed
E37-39	than below
E24	Unrecordable disc				E42	No disc when
						recording
E25-26	Copy prohibited				E43	Already 49 titles
	program					recorded
E29	Disc protected				E44	Already 254 chapters
						recorded
E30	Disc full				E45	Copy prohibited
						program
E35	PCA full *1				E46	It is impossible to
E36	Already finalized					record additionally
						on a disc recorded
	video format disc
						by other units
E40	Some portion has
						when setting “
	not been recorded					Make Recording
	because of program					Compatible” to “OFF”.
	overlapping.
	Recording did not
	start at the start time.

•E23, E27, E28, E31, E32, E33 and E34 are not displayed.

•A program with the error number is grayed in the timer programming list.

•Timer program with an error number will be cleared

once the entry screen for the program is displayed.

*1 PCA is a disc's space reserved for recording test.

30 EN